Related Manuals for Empire V35
Summary of Contents for Empire V35
- Page 1 EMPIRE PAINTBALL ® empirepaintball.com 11723 Lime Kiln Rd. Neosho, MO 64850 Empire is a brand of KEE Action Sports, LLC...
- Page 2 Warnings FOR MANUALS IN OTHER LANGUAGES (WHERE APPLICABLE), GO TO: PAINTBALLSOLUTIONS.COM This product may be covered by one or more of the following patents: 5,954,042; 6,109,252; 6,701,907; 6,792,933; 7,343,909; GB2322438. © All Rights Reserved.
-
Page 3: Page Section
Page Section Page Section ® Introduction EMPIRE v35 Parts Diagram/ List Specifications Troubleshooting Guide ® ® EMPIRE Authorized Upgrade Accessories EMPIRE Warranty Getting Started Warranty Card Battery Installation Attaching the Loader Loading Paintballs ® Activating the EMPIRE ® Powering ON... -
Page 4: Specifications
Electronic Paintball Loader. The EMPIRE Belt Drive Electronic ® Paintball Loader is one of the world’s fastest responding paintball loaders. The EMPIRE series Electronic Paintball Loaders use a spring-driven, true force-feed mechanism which not only keeps the paintball stack intact at all times, but also provides instantaneous acceleration when a ball is needed. - Page 5 Reloader™ B2 Upgrade Kit – Sound activation for increased reliability ® 38929 Empire RF Loader Board Kit – Wireless RF activation for advanced reliability ® ® 38926 Empire RF Transmitter Link Kit – For use with the Empire RF Loader Board Kit...
-
Page 6: Getting Started
. Only use 6- AA batteries installed in the supplied battery holder. ® 2) NEVER use rechargeable packs in place of the supplied 6- AA battery holder. The EMPIRE electronic components are not designed to handle the high output of rechargeable packs. The use of rechargeable packs poses a fire hazard and risk of injury, and will void your warranty. - Page 7 EMPIRE ® V35 model - Press and release the power button on the backplate. The LED will then blink green the number of times to indicate the speed setting, then the motor will begin spinning to wind the drive cone spring and load the ball stack.
-
Page 8: Programming The Speed
Programming the Speed To enter programming mode, while the loader is OFF, press and hold the power button for 5 seconds and the LED begins to flash. Release the button. The LED will flash the current speed selected in green followed by one red flash to indicate the end, then repeat. -
Page 9: General Care
With the loader turned off, turn it upside down to empty the paintballs. For models with an installed Rip Drive™, rotate the Rip Drive™ counter clockwise while the loader is upside down to release the paintballs in the ball stack. Do not store your EMPIRE ®... - Page 10 2) Do not use paper towels on the loader shell as paper towels scratch the plastic. 3) If any paintballs break inside the loader, DO NOT use any liquids or chemicals to rinse out the loader. Pouring liquids or running water through the EMPIRE ®...
-
Page 11: Body Disassembly
Body Disassembly 1) Unscrew the battery door screw, then remove the battery door (28) and battery pack (5). 2) Loosen and remove all 6 screws from the right side shell, making note of which screws go in which holes. 3) Slowly work right side shell (28) straight away from left side shell (28), keeping the drive assembly, circuit board (11) and back plate (12) in the left side shell. - Page 12 Drive Disassembly continued: 4) If access to the motor and gears is necessary, remove the e-clip holding the Rip Drive™ Wheel (15) in place then lift off the Rip Drive™ Wheel (for models equipped with a Rip Drive™), then unscrew the 3 screws holding the gear box cover (17) for access to the gear box.
- Page 13 put the drive cone onto the spring housing and rotate the drive cone clockwise until the upper and lower spring tabs hit each other. You should now have both spring tabs pressed together. Lift the drive cone SLIGHTLY and rotate it clockwise up and over the spring housing’s tab (f), taking the upper spring tab with it.
- Page 14 Body Reassembly - 1) (Figure 1) Seat drive assembly back into left side shell. There are 2 tabs on the side of the drive assembly. Be sure that these 2 tabs seat into the slots in the left side shell. Be sure that the sensor wires flow around the side of the drive assembly, and are not in front of the bottom rear hole in the shell, otherwise the body screw will destroy these wires.
- Page 15 Replacement Parts Kits ® (See page 5 for EMPIRE Authorized Upgrade Accessories) Sku # Description ® 38821 EMPIRE Drive Housing Plastic – Includes Catch Cup, Gear Box Cover, and Upper Feed Neck Cover ® 38873 EMPIRE Snap-Style Lid Kit – Includes Snap-Style Lid, Lid Pin and Lid Spring...
-
Page 16: Schematic & Parts List
EMPIRE ® REF# DESCRIPTION SKU# Rip Drive Wheel 38777 Rip Drive Shaft 38778 Halo V35 Back Plate Sticker 38691 Ball Bearing R188 38803 SChEMAtIC & PARtS LISt Battery Pack - 6 AA 38804 Nut 4-40 38805 Screw 4-40 x 1/4"... - Page 17 EMPIRE ®...
-
Page 18: Troubleshooting
Reflective Sensors may be interfered by sunlight for your marker, and never have a Loader turns ON, does Batteries may be low gap in the ball stack. The EMPIRE ® not spin, then goes into reflective sensors do not Motor may be worn out... - Page 19 During loader Bad paintball is jammed in the feed tube operation, fail safe Anti-jam components are not installed correctly or are broken/missing sequence initiates Reflective Sensors may be blocked by paint or dirt, or not working (alternating red/green LED sequence) Drive Cone may be installed incorrectly Batteries may be low Upper feed neck cover is not attached to the catch cup correctly...
- Page 20 ® ® expressed or implied, made by EMPIRE on this loader. The sole and exclusive liability of EMPIRE and/or its authorized dealers, affiliates, or agents pursuant to this warranty will be for repair or replacement of the defective part; incidental or consequential damages are expressly excluded hereunder. It is the responsibil- ity of the purchaser to pay for shipping fees of the product to the repair facility during the warranty period.
- Page 21 A Return Merchandise Authorization (RMA) is required for service. DO NOT send your product to the ad- dress below without first calling to obtain an RMA. Be sure to mark your RMA number clearly in permanent marker on the package. Packages delivered without a valid RMA will be refused. Paintball Solutions Canada 98 Bessemer Ct Unit 4 London ON N6E 1K7...
-
Page 22: Owner Information
MAIL TO: (Warranty Card) Empire Paintball ® 11723 Lime Kiln Rd. Neosho, MO 64850 OWNER INFORMATION: Your Name: __________________________________________________________________ Address: _____________________________________________________________________ City: __________________________________ State: ______________ Zip: ______________ Country: __________________________________ Phone: _____________________________ Email: _______________________________________________________________________ PURCHASE INFORMATION: Purchased From:______________________________________________________________ City & State: ____________________________________ Phone: _______________________... - Page 24 PAINTBALL LOADING SYSTEM LOADER MANUAL...