Related Manuals for Triax TNR 4
Summary of Contents for Triax TNR 4
- Page 1 Network Digital Video Recorder TNR 4, TNR 8 Model Item no. Network Digital Video Recorder 301050/ 51 triax.com Version...
- Page 2 Please read this quick guide carefully to ensure you can use the device correctly and safely. Triax reserves the right to change the specifications without prior notice. Triax accepts no liability in respect of loss arising from errors in or changes to the information provided.
-
Page 3: Nvr Pre-Installation
NVR Pre-Installation The TNR series NVR are highly advanced surveillance equipment that should be installed with care. Please take into consideration the following precautionary steps before installation of the NVR. 1. Keep all liquids away from the NVR. 2. Install the NVR in a well-ventilated and dust-free area. 3. - Page 4 Connect one end of the data cable to the motherboard of NVR and the other end to the HDD. Connect the power cable to the HDD. Place the HDD on the bottom of the device and then fasten the screws on the bottom to fix the HDD.
-
Page 5: Front Panel
Front Panel LTN7600-P ① USB Interface ② Status Indicators (Alarm, Ready, Status, HDD, power, Tx/Rx) ③ SHIFT ④ Compound Buttons ⑤ Control Buttons Rear Panel TNR Series Item Description Connector for LAN (Local Area Network). LAN Network Interface Connects to RS-485 devices. RS-485 Interface 100~240VAC power supply Power Supply... -
Page 6: Specifications
Specifications Specifications of TNR Series Model TNR 4 TNR 8 LTN7616-P8 IP video input 4-ch 8-ch Video/Audio input 16-ch Two-way audio 1-ch, RCA (2.0 Vp-p, 1kΩ) input Incoming bandwidth 20Mbps 40Mbps Bandwidth Output bandwidth 40Mbps Decoding resolution 5MP/3MP/1080p/UXGA/720p/VGA/4CIF/DCIF/2CIF/CIF/QCIF 1-ch, resolution: HDMI/VGA output 1920 ×... -
Page 7: Hdd Storage Calculation Chart
HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate. Bit Rate Storage Used 128K 160K 192K 224K 256K 112M 320K 140M 384K 168M 448K... -
Page 8: Menu Operation
Menu Operation Menu Structure Startup and Shutdown Proper startup and shutdown procedures are crucial to prolong the life of the NVR. To start your NVR: 1. Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an Uninterruptible Power Supply (UPS) be used in conjunction with the device. - Page 9 Using the Start Wizard By default, the Setup Wizard starts once the NVR has loaded, as shown in Figure below. Start W izard I nterface Operating the Setup Wizard: 1. The Setup Wizard can walk you through some important settings of the NVR. If you don’t want to use the Setup Wizard at that moment, click the Cancel button.
- Page 10 Date a nd T ime S ettings 6. After the time settings, click Next button which takes you back to the Network Setup Wizard window. Network C onfiguration TNR 4 and TNR 8...
- Page 11 Note: For TNR series NVR, the internal NIC IPv4 address should be configured for the cameras connecting to the PoE network interface or the built-in switch of the NVR. 7. Click Next button after configuring the network parameters to take you to the HDD Management window. HDD ...
-
Page 12: Live View
Record S ettings 12. Click Copy to copy the settings to other channels. Copy R ecord S ettings 13. Click OK to complete the startup Setup Wizard. Live View Some icons are provided on screen in Live View mode to indicate different camera status. -
Page 13: Adding And Configuring Ip Cameras
Adding and Configuring IP Cameras You should add and configure the online IP cameras to enable the live view and recording function. Adding IP Cameras You can search and add the online IP cameras by following the startup wizard, or through the following steps. Enter the Camera Management interface. - Page 14 To add other IP cameras: On the left side of the interface, you can enter the IP address, protocol, management port and other information of the IP camera to be added. Click Add to add the camera. Note: If you check the Synchronise IP Camera checkbox, the default settings of the NVR for the IP camera is applied to the added camera.
-
Page 15: Ptz Control
Explanation of the icons: Edit basic parameters of the camera Get the live view of the camera PTZ Control Follow the procedure to set the parameters for PTZ. The configuring of the PTZ parameters should be done before you set the PTZ camera. Before you start, please check that the PTZ and the NVR are connected properly through RS-485 interface. - Page 16 PTZ C ontrol B ar Description o f t he P TZ t oolbar i cons Icon Description Icon Description Icon Description Direction button and Zoom+, Focus+, Zoom-, Focus-, Iris- the auto-cycle button...
- Page 17 Playback Play back the recorded files of a specific channel in the live view menu. Channel switch is supported. Instant playback by channel Steps: Choose a channel in live view mode using the mouse and click the button in the quick setting toolbar. Note: In the instant playback mode, only record files recorded during the last five minutes on this channel will be played back.
- Page 18 Playback I nterface Just check the channel or channels if you want to switch playback to another channel or execute simultaneous playback of multiple channels. Export Recorded files can be backed up to various devices, such as USB flash drives, USB HDDs or a DVD writer. Steps: Enter Video Export interface.
- Page 19 Quick E xport u sing U SB1-‐1 Checkup o f Q uick E xport R esult U sing U SB1-‐1 ...
-
Page 20: Accessing By Web Browser
Accessing by Web Browser Logging In If the device has successfully connected to the network, you can get access to the device via web browser. Open web browser, input the IP address of the device and then press Enter. The login interface appears. Input the user name and password, and click the Login button. - Page 21 Start Live View Steps: In the live view window, select a playing window by clicking the mouse. Double-click a camera from the device list to start the live view. You can click the button on the toolbar to start the live view of all cameras on the device list. Refer to the following table for the description of buttons on the live view window: Icon Description...
- Page 22 Playback Interface Introduction ① Camera List: Displays the list of cameras and the playing status of each camera. ② Playback Window: Displays the video of camera. ③ Play Control Bar: Play control operations are supported. ④ Time Line: Displays the time bar and the records marked with different colors. ⑤...
- Page 23 You can view and export the log files at any time, including operation, alarm, exception and information of device. Before you start The Log function can be realised only when the device is connected with HDD or network disk. And make sure the HDD or network disk has been initialised for the first time to use.
- Page 24 Copyright © 2016 TRIAX. All rights reserved. The TRIAX Logo and TRIAX, TRIAX Multimedia are registered trademarks or trademarks of the TRIAX Company or its affiliates. All specifications in this guide are subject to change without further notice. TRIAX A/S | Bjørnkærvej 3 | DK-8783 Hornsyld | Denmark...