Appliances), and Underwriters Laboratories (UL characteristics as the recommended replacement part Publication UL1410, 59.7). might create shock, fire and / or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate. SyncMaster 150T...
Page 4
Use only an anti-static solder removal device. Some brushing clothes together, or lifting your foot from solder removal devices not classified as “anti-static” a carpeted floor can generate enough static can generate electrical charges sufficient to damage electricity to damage an ESD. ESDs. SyncMaster 150T...
Storage Temperature : -13 °F to 113 °F (-25 °C to 45 °C) Humidity : 5 % to 95 % • SyncMaster 150T complies with SWEDAC (MPRII) recommendations for reduced electromagnetic fields. • Designs and specifications are subject to change without prior notice.
Page 6
2-3 DVI Signal Pin Assignments Signal Assignment Signal Assignment Signal Assignment RX2- RX1- RX0- RX2+ RX1+ RX0+ AGND AGND AGND AGND AGND AGND AGND AGND AGND DDC_SCL DDC Power Input (+5V) AGND DDC_SDA Self-Raster_D RXC+ AGND Connection Signal Output (+5V) RXC- SyncMaster 150T...
Page 7
B : Horizontal sync width O : Frame time total P : Vertical sync width C : Back porch D : Active time Q : Back porch R : Active time E : Front porch S : Front porch SyncMaster 150T...
3 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the SyncMaster 150T monitors. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 3-1 Disassembly Cautions:1. Disconnect the monitor from the power source before disassembly.
Page 10
3 Disassembly and Reassembly 3-2 Replacement Order of Lamp Assemblies - RN15PSS (Samsung Panel) SyncMaster 150T...
Page 11
3 Disassembly and Reassembly SyncMaster 150T...
Page 12
3 Disassembly and Reassembly 3-4 Reassembly Reassembly procedures are in the reverse order of Disassembly procedures. SyncMaster 150T...
DC jack connected to CN102? Does proper DC 5V appear at Check IC104. output Pin of IC100? Does proper 5V-signal Check IC701 and related circuit. appear at Pin 42 of IC701 (CN100, Function Key) (SW-REG-EN)? Check Q101, Q102 and Q103. SyncMaster 150T...
Page 14
(AD_CLK, AD_HSYNC) and does the digital video signal appear Related IC205. at AD_RED (7:0), AD_GRN (7:0),and AD_BLUE (7:0)? During Power on-off, does the signal appear at the Check IC710 and related circuit. Pin 63, 64, 65, 66 of IC501? Replace IC501 and check related circuit. SyncMaster 150T...
Page 15
T_RED (7:0), T_GRN (7:0),and T_BLUE (7:0)? During Power on-off, does the signal appear Check IC701 and related circuit. at the Pin 63, 64, 65, 66 of IC501? Check IC501 and related circuit. SyncMaster 150T...
Page 16
Does the input signal appear at the Pin2, 5 and 10 of IC401? Check IC401 and related circuit. While pushing a front control button does any pulse appear Check IC401 and related circuit. at Pin12 of IC401? Replace IC401. SyncMaster 150T...
Page 17
CH1 RMS = 2.874 V CH1 RMS = 3.903 V CH1 RMS = 1.560V CH1 RMS = 2.469 V CH1 RMS = 2.995 V CH1 RMS = 2.849 V CH1 RMS = 3.311 V CH1 RMS = 3.162 V SyncMaster 150T...