Index Main Page Safety Instructions Notational Power Installation Cleaning Other Introduction Unpacking Front Rear Setup Connecting Your Monitor Installing the Monitor Driver — Automatic — Manual Installing VESA compliant mounting User’s Manual On-Screen Display Troubleshooting Check List Q & A Self-Test Feature Check Specifications General Specifications...
Safety Instructions Notational Warning/Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Notation Conventions Prohibited Do not disassemble Do not touch User’s Manual Important to read and understand at all times Disconnect the plug from the outlet Grounding to prevent an electric shock...
Safety Instructions Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. • Do not use a damaged or loose plug. • This may cause an electric shock or fire. •...
Safety Instructions Power • Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. • Failure to do so may cause an electric shock or fire. • Do not connect too many extension cords or plugs to an outlet.
Safety Instructions Installation • Do not cover the vents on the monitor cabinet. • Bad ventilation may cause a breakdown or fire. • Put your monitor in a location with low humidity and a minimum of dust. • An electric shock or fire could result inside the monitor. •...
User’s Manual Safety Instructions Installation • Do not place the monitor face down. • The TFT-LCD surface may be damaged.
Safety Instructions Clean When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric. • Do not spray detergent directly on the monitor. • Use the recommended detergent with a smooth cloth. • If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth.
Safety Instructions Other • Do not remove cover(or back). No user serviceable parts inside. • This may cause an electric shock or a fire. • Refer servicing to qualified service personnel. • If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized deal- er or service.
Safety Instructions Other • Do not try to move the monitor by pulling on the wire or the signal cable. • This may cause a breakdown, electric shock or a fire due to damage to the cable. • Do not move the monitor right or left by pulling only the wire or the signal cable.
Introduction Unparking • Monitor and Stand • Pivot Stand and S/W CD(Option:SAMSUNG 150S) (Some models include a stand attached. ) Please make sure the following items are included Please make sure the following items are with your monitor. If any items are missing, included with your monitor.
SAMSUNG 190S Introduction Unparking General Monitor and Stand Pivot Stand and S/W CD(Option) (Some models include a stand attached. ) For Multimedia model (Option) Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.11jk Multimedia Speaker Stand (Simple Stand or Pivot Stand &...
Introduction Front : Use this button to auto adjustment direct access. 1. Auto button : Use this button to Exit the active menu or the OSD. 2. Exit button : Use this button to open the OSD and activate a highlighted menu item. 3.
SAMSUNG 190S Introduction Front 1. Auto button 2. Exit button 3. Adjust buttons 4. Menu button 5. Power button 6. Power indicator Note: See PowerSaver functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
Introduction Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port : Connect the power cord for your monitor to the power port on the back of the monitor. 2. Signal cable : Connect the end of the signal cable to your computer's video port. (video board, video card or graphics card) Note : See Connecting Your Monitor for further information regarding cable connections.
SAMSUNG 190S Introduction Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power on/off Switch 2. Power port 3. Multimedia Stand Power Port 4. Signal Port Note: See Connecting Your Monitor Connect the power cord for your monitor to the power port on the back of the monitor.
Setup Connecting Your Monitor 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.. 2. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 3.
SAMSUNG 190S Setup Connecting Your Monitor Setup-General 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
4. Click the "Install" button in the "Warning" window. 5. Monitor driver installation is completed. Windows XP/2000 1. Insert CD into the CD-ROM drive. 2. Click "Windows XP/2000 Driver". 3. Choose your monitor model in the model list, then click the "OK" button. http://www.samsung-monitor.com/ User’s Manual...
5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 6. Monitor driver installation is completed.
2. Click "Start" —> "Control Panel" then click the "Appearance and Themes" Icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced..". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. http://www.samsung-monitor.com/ (Europe) ®...
Setup 5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next"...
Setup This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 9. Click the "Close" button then click "OK" button continually. 10. Monitor driver installation is completed.
Setup ® Microsoft Windows 1. Click "Start" , "Setting" , "Control Panel". 2. Double click "Display" icon. 3. Select the "Settings" tab and click "Advanced Properties" button. 4. Select the "Monitor" tab. 5. Click the "Change" button in the "Monitor Type" area. 6.
Setup 7. Continue choosing "Close" button and "OK" button until you close the "Display Properties" dialogue box. ® Microsoft Windows 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes.
User’s Manual Setup Installing VESA compliant mounting Removing the base 1 Turn off your monitor and unplug its power cord. 2 Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3 Remove the four screws and then remove the Stand from the LCD monitor.
User’s Manual Setup Installing VESA compliant mounting Attaching a base SAMSUNG 170S) NOTE : This monitor accepts a 75mm x 75mm 100mm x 100mm: VESA-compliant mounting interface pad. 1. Rear cover mounting pad 2. Mounting interface pad Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with...
SAMSUNG 190S Setup Installing VESA compliant mounting Removing the base 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove the four screws and then remove the Stand from the LCD monitor.
On-Screen Display Use this button to Exit the active menu or the OSD Use this button to open the OSD and activate a highlighted menu item. Use these buttons to highlight and adjust items using the On Screen Display. These buttons are also direct access buttons for the brightness feature.
Troubleshooting Check List Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the warranty card, the phone number on the Information section or contact your Symptom No images on the Is the power cord connected...
Troubleshooting Check List The screen shows Is the screen displaying only one color as if looking at the screen strange colors or through a cellophane paper? just black and white. Have the screen colors become strange after running a program or due to a crash between applications? Has the video card been set...
Troubleshooting Check List There are only 16 Have the Windows colors been set properly? colors shown on the screen. The screen colors have changed after changing the video card. Has the video card been set properly? There is a message Have you installed the monitor driver? that reads...
Troubleshooting Q&A Question How can I change the frequency? How can I adjust the resolution? How can I set the Power Saving function? How can I clean the outer case/LCD Panel? Answer Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used.
Troubleshooting Self-Test Feature Check Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3.
If the vertical frequency is set at over 76HZ, this message will appear for 5 seconds and then disappear. SAMSUNG 170S) Environment The location and the position of the monitor may influence the quality and other features of the monitor.
Specifications General Power Consumption 30W (Maximum) Dimensions (WxDxH) / Weight 368.5 x 173 x 386.2 mm / 4.0kg (With Simple Stand) VESA Mounting Interface 75mm x 75mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug &...
135 MHz Power Supply AC 90 ~ 264 VAC rms, 60/50 Hz ± 3Hz Signal Cable 15pin-to-15pin D-sub cable, detachable SAMSUNG 170S 17.0 inch diagonal 337.92 (H) x 270.336 (V) 0.264 (H) x 0.264 (V) a-si TFT active matrix 75/75/65/60(L/R/T/B),Typical...
Specifications General Power Consumption 40W (Maximum) Dimensions (WxDxH) / Weight 412 X 209 X 458 mm / 5.9kg (With Simple Stand) VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product.
This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality. As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Power saving mode...
Specifications Preset Timing Modes (SAMSUNG 150S) If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on.
Specifications Preset Timing Modes (SAMSUNG 170S) If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on.
User’s Manual Specifications Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user.
SAMSUNG 190S Specifications General Model Name SAMSUNG 190S LCD Panel Size 19.0 inch diagonal Display area 376.32 (H) x 301.056 (V) Pixel Pitch 0.298 (H) x 0.294 (V) Type a-si TFT active matrix Viewing Angle 85/85/85/85(L/R/T/B) Synchronization Horizontal 30 ~ 81 kHz...
SAMSUNG 190S Specifications For example, the no. of TFT LCD pixels that is contained in this product are 3,932,160. Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings.
EPA/ENERGY (Power button) 2000 Green, Blinking Black Less than 3W Less than 1W TAR ® compliant and ENERGY2000 compliant NERGY Partner, SAMSUNG has determined that this product TAR ® guidelines for energy efficiency. User’s Manual Power off (Power Switch) Black...
SAMSUNG 190S Specifications If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows.
20063 Cernusco s/Naviglio (MI) Servizio Clienti: 199.153.153 http://www.samsung-italia.com/ United Kingdom : Samsung Electronics (UK) Ltd. Samsung House, 225 Hook Rise South Surbiton, Surrey KT6 7LD Tel. : (0208) 391 0168 Fax. : (0208) 397 9949 < European Service Center & National Service >...
Samsung Electronics AB Box 713 S-194 27 UPPLANDS VÄSBY SVERIGE Besöksadress : Johanneslundsvägen 4 Samsung support Sverige: 020-46 46 46 Samsung support Danmark : 8088-4646 Samsung support Norge: 8001-1800 Samsung support Finland: 0800-118001 Tel +46 8 590 966 00 Fax +46 8 590 966 50 http://www.samsung.se/...
Information Terms • Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm •...
(2) this device must accept any interference received, including interference that may cause undesired operation. The party responsible for product compliance: SAMSUNG ELECTRONICS CO., LTD America QA Lab of Samsung 85 West Tasman Drive San Jose, CA 95134 USA Tel) 408-544-5124 Fax) 408-544-5191 Provided with this monitor is a detachable power supply cord with IEC320 style terminations.
Information Regulatory • IC Compliance Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations of ICES-003. Cet appareil Numérique de classe Brespecte toutes les exigences du R?glemont ICES-003 sur les équipements produisant des interférences au Canada. •...
User’s Manual Information Regulatory • TCO'95-Ecological requirements for personal computers (TCO applied model only) AB general requirements AB2 Written Eco-document acompanying the products Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally-adapted electronic products.
Information Regulatory What does labelling involve?(continue) TCO Development Unit 1996-11-29 On the page this folder you will find a brief summary of the environmental requirements met by this product. The complere environmental criteria document may be ordered from: TCO Development Unit S-11494 Stockholm Sweden Fax: +46 8 782 92 07...
User’s Manual Information Regulatory • TCO'99-Ecological requirements for personal computers (TCO applied model only) Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Information Regulatory TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): firstname.lastname@example.org Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings.
The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI). This system is available only for Samsung monitors and makes the color of the images on the monitor the same as the printed or scanned images.
This is not from bad quality and you can use it without uneasiness. For example, the number of TFT LCD pixels that is contained in this product are 2,359,296((SAMSUNG 150S). For example, the number of TFT LCD pixels that is contained in this product are 3,932,160((SAMSUNG 170S).
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.