Advertisement
LED FOLDABLE LIGHT
Indicator function description:
Battery
Data
1.Battery indicator
When the battery indicator light is on: the V-lock battery is being used to power the light.
When the battery indicator light flashes: the V-lock battery is running low.
When the battery indicator light is off: the AC power adapter is being used to power the light.
Note: when the battery is used to power the light, the max output power is reduced to 80%.
2.Data indicator
When the data indicator is on: the DMX512 remote control function is being used.
When the data indicator flashes: the USB port is being used for data upgrade.
The data indicator flashes once each time the light receives an effective remote control signal.
3.USB port operation:
When the device requires a software upgrade, you can connect a USB flash drive through the USB port.
(Upgrade software can be downloaded from www.fotodioxpro.com)
Operation:
(1) Download the updates to an USB flash drive from
(2) Remove the dustproof plug from the USB port and insert the USB flash drive with the upgrade program.
(3) Power on; the DATA indicator light will flash. The upgrade is complete when the "Welcome" message appears
in the LCD display.
(4) It takes about 15 seconds to finish upgrading . After the upgrade is complete, remove the USB flash drive and replace
the dustproof plug.
19
USB
www.fotodioxpro.com
LED FOLDABLE LIGHT
[Menu function instructions:]
1.CCT (color temperature)
M1, M2, M3, M4, M5----------------switch data back and forth with the "Select" knob
CCT (color temp.): 2800-10000 K --------------------adjust using the"selector" knob
GN:-1/+1--------------------------------------------adjust using the "saturation" knob
INT (intensity): 0-100% ---- --------------------------adjust using the "intensity" knob
2.HSI
R+G+B, R+G, R+B, G+B ----------switch back and forth with the "Selector"knob
HUE: 0-360゜ ---- -----------------------------------adjust using the "Selector" knob
SAT (saturation): 0-100% --------------------------adjust using the "Saturation" knob
INT (intensity): 0-100% ----------------------------- adjust using the "Intensity" knob
3.RGBWT
*Mode ONE [M1 M2 M3 M4 M5]
RGBWT selection -------------------------------------adjust using the "Selector" knob
Red: 0-100% ------------------------------------------adjust using the "Intensity" knob
Green: 0-100% ---------------------------------------adjust using the "Intensity" knob
Blue: 0-100% ------------------------------------------adjust using the "Intensity"knob
White: 0-100% ----------------------------------------adjust using the "Intensity" knob
Tungsten: 0-100% -------------------------------------adjust using the "Intensity" knob
4.FX
Use the selector knob to highlight the desired effect. Push the knob once to enter. Use the selector,
saturation and intensity knobs to adjust the parameters.
*OFF
*Party effect
-----SPD (speed): 0-100%
SAT: 0-100%
INT: 0-100%
*Candle
-----SPD: 0-100% COL: warm / warm white / white INT: 0-100%
*Clouds
-----SPD: 0-100%
INT: 0-100%
*Club lights
-----SPD: 0-100%
COL: 03-24
INT: 0-100%
*Color chase
-----SPD: 0-100%
SAT: 0-100%
INT: 0-100%
*Cop car
-----COL: R+B+W / B+W / R+B / B
INT: 0-100%
*Fire
-----SPD: 0-100%
INT: 0-100%
*Fireworks
-----FRQ(frequency): 0-100%
COL: COLOR / WHITE / C+W
*Lightning
-----SPD: 0-100%
INT: 0-100%
INT: 0-100%
20
Advertisement
