Download Print this page

Haier GE WE04M10006 Part Install Instructions

Dryer control boards
Hide thumbs

Advertisement

Quick Links

Part Install Instructions
WE04M10006, WE04M10012, WE04M10014, WE04X21166
And WE10X23597 Dryer Control Boards
!
IMPORTANT SAFETY NOTICE
The information in this part instruction is intended for use by
individuals possessing adequate backgrounds of electrical,
electronic and mechanical experience. Any attempt to repair a
major appliance may result in personal injury and property
damage. The manufacturer or seller cannot be responsible for
the interpretation of this information, nor can it assume any
liability in connection with its use.
Parts Included:
Control Board
Overview – Procedure for programming new control boards.
Programming a new control board in some cases
may not be necessary. However, if after a new
control board is installed, the dryer is powered up,
and 3 dashes (---) appear in the display, follow the
instructions below.
1. Simultaneously press TEMP and LEVEL. Display
will start blinking allowing model to be set.
2. The User Interface (UI) model code will be
displayed first. (0 00)
3. Pressing either TEMP or LEVEL will increment or
decrement the UI model code. NOTE: If there is
just one model code, (0 00) will not change.
4. Pressing START will temporarily save the model
code until the heater type is selected. g or E will
be displayed
5. Press either TEMP or LEVEL to alternate
between the two heat sources.
6. Press and hold START for 3 seconds to save.
Machine will go idle if set successfully.
If an error is made programming the control or if 3 dashes are not displayed, enter service mode
as shown on the back of these instructions. Use service mode test 1 to correct on all models
except for GFDN160 and GFDS170 models. Test 2 would need to be entered for them.
Press the start button to enter service mode test and then press and hold TEMP and LEVEL at
the same time. Display will start blinking.
Instruction Sheet
!
WARNING
To avoid personal injury, disconnect power before servicing
this appliance. If electrical power is required for diagnosis or
test purposes, disconnect the power immediately after
performing the necessary checks. RECONNECT ALL
GROUNDING DEVICES If grounding wires, screws, straps,
clips, nuts, or washers used to complete a path to ground are
removed for service, they must be returned to their original
position and properly fastened.
UI Display
WE10X23597
WE04X21166
WE04M10014
WE04M10012
WE04M10006
WE04M10006
Dryer Model
GFDN160EJ
GFDN160GJ
000
GFDS170EH
GFDS170GH
GFDN110ED
001
GFDN110GD
GFDN120ED
GFDN120GD
002
GFDN130ED
GFDN130GD
GFDS140ED
GFDS140GD
003
GFDS145ED
GFDS145GD
GFDS150ED
GFDS150GD
004
GFDS155ED
GFDS155GD
WE00X27074

Advertisement

loading

  Related Manuals for Haier GE WE04M10006

  Summary of Contents for Haier GE WE04M10006

  • Page 1 Part Install Instructions WE04M10006, WE04M10012, WE04M10014, WE04X21166 And WE10X23597 Dryer Control Boards WARNING IMPORTANT SAFETY NOTICE To avoid personal injury, disconnect power before servicing The information in this part instruction is intended for use by this appliance. If electrical power is required for diagnosis or individuals possessing adequate backgrounds of electrical, test purposes, disconnect the power immediately after electronic and mechanical experience.
  • Page 2 Service Mode Entry Procedure Per Model. From an idle state, press and hold the “SIGNAL” and “LOCK” buttons for 3 seconds to enter service mode. Upon entering the service mode, the control will be in test selection mode and display GFDN110 the first test number (t01).

This manual is also suitable for:

Ge we04m10012Ge we04m10014Ge we04x21166Ge we10x23597