Telit Wireless Solutions SL869T3-I User Manual
Evaluation kit
Hide thumbs
Also See for SL869T3-I:
- Product user manual (57 pages) ,
- Product user manual (57 pages) ,
- Product user manual (68 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Telit Wireless Solutions SL869T3-I
Summary of Contents for Telit Wireless Solutions SL869T3-I
- Page 1 SL869T3-I Evaluation Kit User Guide 1VV0301561 Rev. 2 2019-11-07...
-
Page 2: Notice
SL869T3-I Evaluation Kit User Guide Notice SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Notice While reasonable efforts have been made to ensure the accuracy of this document, Telit assumes no liability resulting from any inaccuracies or omissions in this document, or from use of the information obtained herein. -
Page 3: Usage And Disclosure Restrictions
SL869T3-I Evaluation Kit User Guide Notice USAGE AND DISCLOSURE RESTRICTIONS License Agreements The software described in this document is the property of Telit and its licensors. It is furnished by express license agreement only and may be used only in accordance with the terms of such an agreement. -
Page 4: Product Applicability Table
SL869T3-I Evaluation Kit User Guide Product Applicability Table Product Applicability Table PRODUCT SL869T3-I EVK Table 0-1 Product Applicability Table 1VV0301561 Page 4 of 31 2019-11-07 Rev. 2... -
Page 5: Table Of Contents
EVALUATION KIT REQUIREMENTS ................10 EVALUATION KIT DESCRIPTION ..................11 EVK Contents ....................... 11 Evaluation Board Description ..................12 3.2.1 SL869T3-I Evaluation Board - CS1764 ..............13 3.2.2 EVK Board Component Identification ................ 15 3.2.3 EVK Board Schematics .................... 17 Module Image ....................... - Page 6 DOCUMENT HISTORY ..................... 30 TABLES Table 0-1 Product Applicability Table ..................... 4 Table 3-1 SL869T3-I EVK Board Component Identification - CS1674 ........... 15 Table 7-1 Output messages ......................28 Table 7-2 Commands ........................29 Table 8-1 Document History ......................30...
-
Page 7: Figures
Figure 3-4 SL869T3-I Evaluation Board Components - CS1764 ............ 14 Figure 3-5 Jumpers Pre-installed for SL869T3-I Operation ............16 Figure 3-6 SL869T3-I Evaluation Board Schematic Page 1/2 - CS1764 ........17 Figure 3-7 SL869T3-I Evaluation Board Schematic Page 2/2 - CS1764 ........18 Figure 3-8 SL869T3-I Module ...................... -
Page 8: Introduction
Introduction Introduction 1.1 Purpose This guide explains how to set up the SL869T3-I Evaluation Kit (EVK) to begin evaluating the SL869T3-I GNSS modules. 1.2 Contact and Support Information For general contact, technical support services, technical questions, and to report documentation errors contact Telit Technical Support at: •... -
Page 9: Related Documents And Downloads
SL869T3-I Evaluation Kit User Guide Introduction 1.4 Related Documents and Downloads under” NavIC+GPS” and select “SL869T3-I” for current Visit http://www.telit.com/gnss/, documentation and downloads. • SL869T3-I Datasheet • SL869T3-I Product User Guide, 1VV0301546 • V34 Software User Guide, 1VV0301590 • TelitView installation package 1.4.1 Related Documents Requiring a Non-Disclosure Agreement... -
Page 10: Evaluation Kit Requirements
Evaluation Kit Requirements Evaluation Kit Requirements The SL869T3-I module is specifically designed to meet the requirement to receive and process L5 band signals from the NavIC (formerly IRNSS) constellation along with GPS L1. To use the SL869T3-I Evaluation Kit (EVK), you will need the following items:... -
Page 11: Evaluation Kit Description
SL869T3-I Evaluation Kit User Guide Evaluation Kit Description Evaluation Kit Description 3.1 EVK Contents The SL869T3-I EVK includes the following: • Evaluation Board with the SL869T3-I Module • L1+L5 Antenna • Ground Plane • USB cable 2m Figure 3-1 EVK Contents... -
Page 12: Evaluation Board Description
SL869T3-I Evaluation Kit User Guide Evaluation Kit Description 3.2 Evaluation Board Description IMPORTANT INFORMATION! The Evaluation Board must be completely powered down (disconnected from the USB cable) before changing any jumper or antenna connection. The antenna supplied in the evaluation kit is designed to receive both L1 and L5 signals. -
Page 13: Sl869T3-I Evaluation Board - Cs1764
SL869T3-I Evaluation Kit User Guide Evaluation Kit Description 3.2.1 SL869T3-I Evaluation Board - CS1764 Figure 3-2 SL869T3-I Evaluation Board - CS1764 Figure 3-3 SL869T3-I Evaluation Board Components - CS1764 1VV0301561 Page 13 of 31 2019-11-07 Rev. 2... -
Page 14: Figure 3-4 Sl869T3-I Evaluation Board Components - Cs1764
SL869T3-I Evaluation Kit User Guide Evaluation Kit Description Figure 3-4 SL869T3-I Evaluation Board Components - CS1764 1VV0301561 Page 14 of 31 2019-11-07 Rev. 2... -
Page 15: Evk Board Component Identification
1PPS Output SMA 1PPS buffered output SW 101 Reset Switch Pushbutton to reset the module SW 201 ON/OFF Switch Applies power to the module Table 3-1 SL869T3-I EVK Board Component Identification - CS1674 1VV0301561 Page 15 of 31 2019-11-07 Rev. 2... -
Page 16: Figure 3-5 Jumpers Pre-Installed For Sl869T3-I Operation
SL869T3-I Evaluation Kit User Guide Evaluation Kit Description Figure 3-5 Jumpers Pre-installed for SL869T3-I Operation 1VV0301561 Page 16 of 31 2019-11-07 Rev. 2... -
Page 17: Evk Board Schematics
SL869T3-I Evaluation Kit User Guide Evaluation Kit Description 3.2.3 EVK Board Schematics Figure 3-6 SL869T3-I Evaluation Board Schematic Page 1/2 - CS1764 1VV0301561 Page 17 of 31 2019-11-07 Rev. 2... -
Page 18: Figure 3-7 Sl869T3-I Evaluation Board Schematic Page 2/2 - Cs1764
SL869T3-I Evaluation Kit User Guide Evaluation Kit Description Figure 3-7 SL869T3-I Evaluation Board Schematic Page 2/2 - CS1764 1VV0301561 Page 18 of 31 2019-11-07 Rev. 2... -
Page 19: Module Image
SL869T3-I Evaluation Kit User Guide Evaluation Kit Description 3.3 Module Image Figure 3-8 SL869T3-I Module 1VV0301561 Page 19 of 31 2019-11-07 Rev. 2... -
Page 20: Evaluation Kit Setup
SL869T3-I Evaluation Kit User Guide Evaluation Kit Setup Evaluation Kit Setup This section provides step-by-step instructions on how to setup the evaluation kit. 4.1 Preparation IMPORTANT! The Evaluation Board must be completely powered down (disconnected from the USB cable) before changing any jumper or antenna connection. -
Page 21: Figure 4-2 Identify New Com Port
SL869T3-I Evaluation Kit User Guide Evaluation Kit Setup Click “Continue Anyway” to install the USB-COM Port Driver When the EVK board is connected to a personal computer USB port, the driver creates a COM port. Use the Windows “Device Manager” to check the identification of the new COM port. -
Page 22: Install Current Version Of Telitview
Visit www.telit.com/gnss Under “NavIC +GPS”, click “SL869T3-I” Under “SL869T3-I Downloads”, click “Development Kit and Tools User Guide” and then click “Telit_View_Install_xxx” Once the file has finished downloading, run the executable file and follow the steps in the TelitView XXX Setup Wizard. -
Page 23: Using Telitview
SL869T3-I Evaluation Kit User Guide Using TelitView Using TelitView This section provide the step-by-step instructions on how to use the TelitView application. For a detailed information about the application, please refer to the TelitView User Guide available in the downloaded TelitView product package. Alternatively, you can also view the document under the “Help”... -
Page 24: Main Menu Bar
SL869T3-I Evaluation Kit User Guide Using TelitView 5.2.2 Main Menu Bar Figure 5-2 Main Menu Bar and Tool Bar • Click Setup > COMM Port. The “Connect to Receiver” window appears. 5.2.3 “Connect to Receiver” window Figure 5-3 “Connect to Receiver” window •... -
Page 25: Connection Status
SL869T3-I Evaluation Kit User Guide Using TelitView 5.2.4 Connection Status The status bar will show the current communication state: “Connected [COMxx, Baud xxxx]”, as indicated by the following figure. Figure 5-4 Connection Status For more information, please refer to the built-in “Help” tab or the TelitView User Guide which is installed along with the TelitView application. -
Page 26: Flashing Firmware With X-Loader
2. Connect the USB cable and let the Host PC machine enumerate the USB connection. 3. Set SW201 (Main Power) to ON (up) to power the SL869T3-I module. 4. Launch the TESEOIII X-Loader and set the selections as shown in the figure below. - Page 27 SL869T3-I Evaluation Kit User Guide Flashing Firmware with X-Loader 5. Click “Load” button to locate and select the software provided by Telit. 6. Verify the selections as follows: a. “Target device” is SQI flash b. “Erase NVM” is selected c. “STA8090FG Only” is selected d.
-
Page 28: Message Interface
All messages are output once per second. There are multiple GSA and GSV messages output each second. 7.2 Commands (Input) A command is a defined Data Packet sent from a host processor to the SL869T3-I GNSS module. The regular structure of the command is: command-ID[,<parameters>]<cr><lf>... -
Page 29: Commands Description
$PSTMSETCONSTMASK Set the GNSS constellation mask Table 7-2 Commands Unless otherwise noted in the SL869T3-I SW User Guide document, commands are echoed by the SL869T3-I module once the command is executed. Note: Not all commands may be fully supported 1VV0301561... -
Page 30: Document History
SL869T3-I Evaluation Kit User Guide Document History DOCUMENT HISTORY Revision Date Changes 2018-10-31 First issue Updated Xloader version to 2.1 Updated module photo Updated EVB photo, added information and schematics 2019-11-07 Minor text changes for grammar and clarity Updated with Production HW & FW information...
Need help?
Do you have a question about the SL869T3-I and is the answer not in the manual?
Questions and answers