Advertisement
Table of Contents
Here are some suggestions for setting up a simple race course for boats:
Make 3 simple "Maker Buoys" with beach ball, string, and heavy objects for anchors, similar to the above
sketch. Place the buoys as above sketch. for "OVAL RACING" The length can be vary.
40M
MEMO
OUTLAW 7.5
START/FINISH
20M
20M
30M
12
OUTLAW 7.5
Assembly Manual
50M
No.5213
Specifications:
Length: 42.9" (1090mm)
Beam: 12.4" (315mm)
Height: 9.6" (243mm)
Weight: 3500g (7.7lb.)
Engine: TTPRO-46M Installed
This kit is guaranteed to be free from defects in material and workmanship at the date of purchase.
It does not cover any damage caused by use or modification. The warranty does not extend
beyond the product itself and is limited only to the original cost of the kit. By the act of building this
user-assembled kit, the user accepts all resulting in liability for damage caused by the final
product. If the buyer is not prepared to accept this liability, it can be returned new and unused to
the place of purchase for a refund.
This is not a toy. Assembly and running this product requires adult supervision.
Read through this book completely and become familiar with the assembly of this boat. Inspect all
parts for completeness and damage.
customer service if you encounter any problems.
Off-Shore Deep Vee
Warranty
Notice: Adult Supervision Required
Browse www.thundertiger.com for more information or
1
JJ6083
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for THUNDER TIGER Outlaw 7.5
Summary of Contents for THUNDER TIGER Outlaw 7.5
- Page 1 OUTLAW 7.5 Here are some suggestions for setting up a simple race course for boats: OUTLAW 7.5 Make 3 simple “Maker Buoys” with beach ball, string, and heavy objects for anchors, similar to the above sketch. Place the buoys as above sketch. for “OVAL RACING” The length can be vary.
- Page 2 OUTLAW 7.5 INTRODUCTION ITEMS NEEDED INTRODUCTION ITEMS INSTALLED 4 way Wrench-Easy to unplug T h a n k f o r p u r c h a s i n g T h u n d e r T i g e r O u t l a w 7 . 5 O f f - S h o r e D e e p V e e ! T h i s p e r f o r m a n c e r a c i n g b o a t the glow plug.
- Page 3 OUTLAW 7.5 PARTS LISTING PARTS DRAWINGS PJ6088 Hatch Cover PJ6087 Hull PN0297 AA1813 PN1806 PN1807 PN0296 Clutch Shoes Clutch Bell Flywheel Set Flywheel Shim Clutch Spring Collet (1) Ball Bearing (2) Clutch Spring (4) Clutch Shoes (4) Clutch Bell (1)
- Page 4 OUTLAW 7.5 OUTLAW 7.5 1.Carefully remove your Outlaw stand kit from the 4.Open the hatch cover with your index finger at the 7.Use balloon to well wrap the receiver and battery 9.Remove the sleeve of water fin before starting the box.
- Page 5 OUTLAW 7.5 OUTLAW 7.5 15.Place the boat in water to break-in the engine or 12.Remove the glow plug by using the 4-way wrench. engine will overheated and damaged. As soon as Choke some fuel in by blocking the carb for a second 18.Run the boat in rich about two tanks then you can...
- Page 6 Conversely, Outlaw. This is prohibited at any lake or pond. FFMN www.ffma.fr The Outlaw 7.5 has two trim tabs at the transom. moving the trigger forward, throttle is closed Suggest to do the all adjustment in calm water.
Need help?
Do you have a question about the Outlaw 7.5 and is the answer not in the manual?
Questions and answers