Table of Contents
Advertisement
Precautions for use
Cautions when installing
Do not set up the Display outdoors.
The Display is designed for indoor use.
•
Install this unit at a location which can support the
weight of the unit.
Dropping or falling of the unit may cause injury.
•
Environmental temperature to use this unit
When using the unit where it is below 1 400 m
•
(4 593 ft) above sea level: 0 °C to 40 °C (32 °F to
104 °F)
When using the unit at high altitudes (1 400 m
•
(4 593 ft) and higher and below 2 800 m (9 186 ft)
above sea level): 0 °C to 35 °C (32 °F to 95 °F)
Do not install the unit where it is 2 800 m (9 186 ft)
and higher above sea level.
Failure to do so may shorten the life of the internal
•
parts and result in malfunctions.
We are not responsible for any product damage, etc.
caused by failures in the installation environment
even during the warranty period.
Transport only in upright position!
Transporting the unit with its front panel facing upright
•
or downward may cause damage to the internal
circuitry.
Do not install the product to a place where the
product is exposed to direct sunlight.
If the unit is exposed to direct sunlight even indoors,
•
the temperature rise of the liquid crystal panel may
cause malfunction.
Required space for ventilation
Operation of this unit is guaranteed up to an ambient
•
temperature of 40 °C (104 °F). When installing the
unit in a case or chassis, be sure to provide adequate
ventilation with a cooling fan or ventilation hole so
that the surrounding temperature (inside the case or
chassis) including the temperature of the front surface
of the liquid crystal panel can be kept at 40 °C
(104 °F) or less.
About the screws used when using a wall hanging
bracket that conforms to VESA standards
Inch
Screw pitch for
model
installation
75
600 mm × 400 mm
65
400 mm × 400 mm
8
English
Depth of
Screw
screw hole
(quantity)
15 mm
M8 (4)
15 mm
M8 (4)
Note for connection
Removing and inserting the power cord and
connection cables
When the unit has been installed on the wall, if the
•
power cord and connection cables are difficult to
remove and insert, make connections first before
installation. Be careful not to allow the cables to be
entangled. After installation is completed, insert the
power plug to the outlet.
When using
Red, blue or green dots on the screen are a liquid
crystal panel-specific phenomenon. This is not a
malfunction.
Although the liquid crystal display is manufactured
•
with high-precision technology, always-lighting dots or
non-lighting dots may appear on the screen. This is
not a malfunction.
Inch model
Dot omission ratio*
75
0.00009% or less
65
0.00005% or less
*: Calculated in sub-pixel units according to the
ISO09241-307 standard.
Depending on the temperature or humidity
conditions, uneven brightness may be observed.
This is not a malfunction.
This unevenness will disappear while applying current
•
continuously. If not, consult the distributor.
If the Display is not going to be used for any
prolonged length of time, unplug the power supply
plug from the wall outlet.
Picture noise may occur if you connect / disconnect
the cables connected to the input terminals you
are currently not watching, or if you turn the power
of the video equipment on / off, but it is not a
malfunction.
Notes on Using Wired LAN
When setting up the Display at a place, where
electric statistic occurs often, take a sufficient
antistatic measure before start using.
When the Display is used at a location, where static
•
electricity occurs often, such as on a carpet, a wired
LAN communication is disconnected more often.
In that case, remove static electricity and the noise
source that may cause problems with an antistatic
mat, and re-connect the wired LAN.
In rare cases, the LAN connection is disabled due
•
to static electricity or noise. In that case, turn off the
power of the Display and the connected devices once
and then re-turn on the power.
The Display may not work properly due to strong
radio wave from the broadcast station or the radio.
If there is any facility or equipment, which outputs
•
strong radio wave, near the installation location, set
up the Display at a location sufficiently far from the
source of the radio wave. Or, wrap the LAN cable
connected to the LAN terminal by using a piece of
metal foil or a metal pipe, of which is grounded at
both ends.
Advertisement
Table of Contents
