Introduction Congratulations! You’ve purchased the most advanced, feature-rich integrated inverter/charger on the market. Your APS powers connected equipment, switching manually or automatically from utility power to power inverted from an external battery or batteries. In addition to reliable APS performance, your model provides: High Efficiency Output Your APS’s advanced circuitry produces a more efficient DC-to-AC conversion, minimizing energy loss.This allows you to run connected equipment longer between battery charges.
Page 3
Introduction 3-Stage Battery Charger Your APS recharges your battery faster than conventional chargers because its three-stage charger profile (Bulk,Absorption and Float) is optimized for the type of battery you use (Wet or Gel).* In addition, the advanced charging system protects against over-charge and over-discharge to ensure a longer service life from your battery.
Serious injury to property or person could result. Equipment Connection Warnings • Do not use Tripp Lite APS Systems in life support applications where a malfunction or failure of a Tripp Lite APS System could cause failure or significantly alter the performance of a life support device.
Configuration DIP Switches Using a small tool, set the four “Battery Type / Voltage Point” Configuration DIP Switches (located on the front panel of your APS); see Diagram 4, p. 28. • Select Battery Type CAUTION:The Battery Type DIP Switch setting must match the type of batteries you connect or your batteries may be degraded or damaged over an extended period of time.
Battery Selection Selecting Battery Type Select a battery or system of batteries that will provide your APS with proper DC voltage and an adequate amp hour capacity.* Select ‘Deep-Cycle’ batteries to enjoy optimum performance from your APS. Batteries of either Wet-Cell (vented) or Gel-Cell/Absorbed Glass Mat (sealed) construction are ideal.
Battery Connection 1. Make sure that your APS batteries have proper overcurrent protection. NEC article 551 requires that you install a recognized UL component fuse block and UL listed fuse within 18 inches of the battery. The fuse’s rating must equal or exceed the Minimum DC Fuse Rating listed in your APS model’s specifications on page 13.
Page 8
Note: when the switch is in the "AUTO/REMOTE" position, you can remotely monitor and control your APS by connecting a Tripp Lite Remote Control Module (sold separately) to the APS's RJ45 Remote Module Connector. • • Switch to “CHARGE ONLY” when you are not using your connected equipment.
Switches, Indicator Lights & Other Features (See Diagram 4, p. 28, to locate the following switches, indicator lights and other features.) Switches 1 1 . . O O p p e e r r a a t t i i n n g g M M o o d d e e S S w w i i t t c c h h : : This switch selects the APS operating mode (either “AUTO/REMOTE”, “OFF”...
Switches, Indicator Lights & Other Features Other Features 7 7 . . D D C C P P o o w w e e r r T T e e r r m m i i n n a a l l s s : : These terminals should be wired to your battery terminals. See “Battery Connection”, p.
Limited Warranty Tripp Lite warrants its products to be free from defects in materials and workmanship for a period of one year (domestic) or 120 days (export) from the date of initial purchase. Tripp Lite’s obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products.
Troubleshooting Try these remedies for common APS problems before calling for help. Call Tripp Lite Customer Service at (773) 869-1234 before returning your APS for service. SYMPTOM APS does not provide AC output (AC input present) APS does not provide...
Specifications MODEL: SERIES: Weight: INVERTER Continuous power (@ 20° C): Surge power: Efficiency (Full Load): Minimum/Maximum DC Fuse Rating: DC Input Current @ Nominal V DC Full Load Nominal Input Volts: DC Input Voltage Range: Nominal Output Volts: Nominal Output Frequency: BATTERY CHARGER Charging Capacity DC: Maximum Cable Length...
Introducción ¡Felicitaciones! Usted ha adquirido el inversor / cargador de batería integrado más avanzado y con más características en el mercado. Este modelo APS suministrará a sus equipos energía de CA mientras ésta esté presente. Durante un apagón, caída o subida de voltaje, esta unidad cambia automáticamente a la batería externa para suministrar energía de CA de voltaje y frecuencia controlada.
Page 16
Introducción Cargador Avanzado de 3 Etapas para Baterías Este sistema APS recargará sus baterías más rápido que otros cargadores convencionales debido a que su perfil de recarga de 3 etapas (Alimentación Alimentación por Flotador) provee óptimo rendimiento independientemente del tipo de baterías que usted utilice (Húmeda o de Gel).* Además, el sistema avanzado de recarga protege contra exceso de carga y descarga...
Precauciones Sobre la Conexión de Equipos • No utilice los Sistemas APS de Tripp Lite en aplicaciones para el soporte de la vida humana donde una falla del APS pueda causar anomalías o alterar significativamente el rendimiento del dispositivo de soporte de vida.
Configuración Interruptores DIP Usando una herramienta pequeña, ajuste los 4 Interruptores DIP de Configuración, Grupo A: “Battery Type / Voltage Point” (tipo de baterías / punto de voltaje) ubicados en el panel frontal del sistema APS (vea el Diagrama 4, página 28) para seleccionar el tipo de baterías que desea utilizar y programar el rango de voltaje para el cambio automático del sistema APS a energía de batería.
Selección de Baterías Seleccione el Tipo de Batería(s) Seleccione una batería o sistema de baterías que suministre voltaje apropiado de CD y capacidad adecuada en amperios / hora al sistema APS.* Seleccione baterías de ciclo profundo para obtener el máximo rendimiento de su sistema APS. Las baterías húmedas (ventiladas) o de gel / fibra de vidrio absorbido (selladas) son ideales.
Page 20
Conexión de Baterías 1. Confirme que las baterías del APS cuenten con adecuada protección para sobrecargas de corriente. El artículo NEC 551 requiere que usted instale un bloque de fusibles de componente UL reconocido y un fusible UL listado a 18 pulgadas de la batería. La capacidad en amperios del fusible debe ser igual o superior a la capacidad mínima de amperios de CC del fusible que se muestra en la ficha técnica del modelo del APS en la página 26.
Page 21
Nota: cuando el conmutador está en la posición "AUTO/REMOTE", puede vigilar y controlar su APS conectando un Módulo de control remoto de Tripp Lite (vendido por separado) al conector RJ45 del módulo remoto del APS. • Colóquelo en la posición “CHARGE ONLY” (recarga solamente) cuando usted no necesite utilizar los equipos conectados.
Interruptores, Luces Indicadoras y Otras Características (Vea el Díagrama 4 en la página 28 para localizar los siguientes interruptores, luces indicadoras y otras características.) Interruptores 1 1 . . I I n n t t e e r r r r u u p p t t o o r r “ “ O O p p e e r r a a t t i i n n g g M M o o d d e e ” ” ( ( M M o o d d o o d d e e o o p p e e r r a a c c i i ó ó n n ) ) : : Este interruptor selecciona el modo de operación del sistema APS: “AUTO/REMOTE”...
Page 23
Interruptores, Luces Indicadoras y Otras Características 6 6 . . “ “ B B A A T T T T E E R R Y Y H H I I / / M M E E D D / / L L O O ” ” ( ( B B A A T T E E R R Í Í A A H H I I / / M M E E D D / / L L O O ) ) : : Estas tres luces se encenderán en varias secuencias para mostrar el nivel de carga y el voltaje aproximados del banco de baterías conectado y advertirle sobre varias fallas: INDICACIÓN DE LA CARGA DE LA BATERÍA (Aproximado)
Garantía Limitada Tripp Lite garantiza que sus productos estarán libres de defectos en materiales y mano de obra por un período de un año (unidades utilizadas en EE.UU.) ó 120 días (unidades utilizadas fuera de EE.UU) a partir de la fecha inicial de compra.
Resolucion de Problemas Si experimenta problemas comunes refiérase a esta guía antes de llamar al centro de servicios. Llame al Servicios a Clientes de Tripp Lite antes de enviar el sistema APS. SIMTOMA El sistema APS no suministra salida de CA (energía de CA...
Especificaciones MODELO: SERIO: Peso: INVERSOR Energía continua a 20º C Energía de sobretensiones transitorias: Eficiencia (Carga Completa): Indice Mínimo/Maximo de Capacidad del Fusible: Corriente de Entrada de CD a Niveles Nominales Carga Completa: Voltios Nominales de Entrada: Gama de Voltaje de Entrada de CD: Voltios Nominales de Salida: Frecuencia Nominal de Salida: CARGADOR DE BATERIAS...
Page 27
Diagrams/Esquemas See Battery Connection, Pg. 7. 1.1 is the fuse. X = Your APS’s Inverter's Nominal Input Voltage. (See specs.) Refiérase a la sección Conexión de baterías, Pág. 20. 1.1 representa el fusible. X = Voltaje nominal de entrada del inversor del APS.
Need help?
Do you have a question about the PowerVerter APS 612 and is the answer not in the manual?
Questions and answers