Advertisement
Quick Links
Advertisement
Related Manuals for Igloohome Smart Deadbolt 02
Summary of Contents for Igloohome Smart Deadbolt 02
- Page 1 Installers guide Deadbolt 02. version 0.7.1...
-
Page 2: Specifications
Specifications Model igloohome Smart Deadbolt 02 Material Zinc Alloy Current Rating (Standby) ~30uA Current Rating (Active) ~200mA Batteries 4 x AA Alkaline (Non - Rechargeable) Unlock Mechanism Bluetooth, PIN code, Keys Front Side Back 60 mm 30 mm 45 mm... - Page 3 *Please ensure that there is an existing handle on your door for push - pull access * Not for: metal gates, glass doors or sliding doors. If you are unsure if your door is suitable, send us web links to your door pictures to support@igloohome.co...
-
Page 4: What's Included
What’s included Battery Case Lid Front Assembly Rubber Gasket Back Assembly Back Plate Bolt Assembly AA Batteries Keys Strike Plate 5 mm 25 mm Bolt Screw Wood Screw 22 mm 40 mm Screw Strike Plate Drill Sheet Bolt Screw Bolt Screw Holder Housing... -
Page 5: Recommended Tools
Recommended Tools #2 Phillips Screw Driver 25mm Spade Bit Chisel Hammer 54 mm Hole Saw 10 mm Drill Bit Drill... -
Page 6: Installation Type
Installation type b. Left installation a. Right installation... - Page 7 Drill holes on door (For new installation) 1. For new doors or doors without existing deadbolt lock, you will need to drill holes in your door to mount your deadbolt. Use measurements provided on the Drill Sheet to drill holes in the door. Right installation Left installation Determine height of door to install.
- Page 8 Insert bolt assembly 1. If you are replacing your current deadbolt lock, industry standards are 60mm or 70mm backset. To determine which backset length you should use, so measure the distance (x) between the center of 54mm hole to door edge. 54mm hole 23/4”...
- Page 9 2. Prepare bolt assembly based on the distance (x) Bolt ships with bolt assembly in 60mm position. If required, twist the bolt and pull to extend (simultaneously) to 70mm backset position (current drill dimensions are fitted for 60mm position). 60mm position 70mm position 1 Twisted 23/4”...
- Page 10 1. Insert bolt assembly. 2. Mark around the plate of the bolt tongue and chisel about 2mm or until bolt tongue plate is flush with the door.
- Page 11 Secure the bolt assembly onto door using 2 x 25mm wood screws. 23/4” 23/8” 25mm wood screws...
- Page 12 Prepare lock and parts 1. Set Back Assembly a. Right installation (Refer to page 6 for installation type) To install the lock for right-side installation (i.e. bolt locks to the right from outside the door), ensure the toggle button on the back assembly is set to R. b.
- Page 13 2. Check that the thumbturn has been set correctly. It should turn in the following orientation. Right installation Left installation Magnet Magnet 3. Screw on Screw Holder into the 10mm hole on the Front Assembly Screw holder should go to the front assembly. The size of screwholder should go smaller relative to front assembly...
- Page 14 Mount lock 1. Set Tailpiece on the Front Assembly according to the following alignment. 2. Fit Front Assembly (with Rubber Gasket attached) through the 54mm hole and 10mm hole. Ensure that the tailpiece slots through the bolt assembly according to the previously set alignment. b.
- Page 15 a. Right installation The tailpiece must be turned clockwise all the way until it is in the horizontal position. Slot it horizontally through the Bolt Assembly Tailpiece a. Right installation...
- Page 16 3. Secure the Front Assembly using the Back Plate. To do this, place the Back Plate (ensuring the correct side placement), and screw it to the Front Assembly using the three 40mm bolt screws Follow this orientation The cable should come out from the side...
- Page 17 4. Fit Back Assembly over the Back Plate, aligning the three holes (two under the Battery Cradle, and one at the bottom of the Back Assembly) to the Back Plate 40 mm bolt screw (x3)
- Page 18 5. Connect wire connector from Front Assembly through 54mm hole to Back Assembly. Make sure that the wire is installed properly and securely.
- Page 19 6. Remove the Battery Case Lid Use a sharp object to depress pin and pull battery case upwards.
- Page 20 7. Secure the two holes under the battery casing with 2 x 5mm bolt screws and the bottom with 22mm bolt screw Align holes on back assembly to back plate and screw in. * Make sure this is turned to ‘unlock’ position. * For right installation, turn thumbturn clockwise before mounting and for left installation, turn thumbturn anti-clockwise before mounting.
- Page 21 8. Make sure 4 x AA Batteries are inserted correctly before closing the Battery Case Lid...
- Page 22 Tailpiece and/or thumbturn Left-Right toggle incorrectly incorrectly set. set. Troubleshoot: Dissemble lock Troubleshoot: Try setting the and install it again. left-right toggle on your back assembly to the correct side Still experiencing issues? Go to igloohome.co/support for more help...
- Page 23 Drill holes in door frame 1. Make sure to align the lock to the frame and mark it down. Door Frame Mark Hole 2. Mark out where the bolt tongue locks then drill a corresponding hole on door frame.
- Page 24 3. Mark out the strike plate and use the chisel 2mm or until the strike plate is flush. 4. Secure strike plate housing and strike plate using 2 x 25mm wood screws.
- Page 25 For enquiries go to: igloohome.co/support...