Advertisement
Available languages
Available languages
Quick Links
Advertisement
Summary of Contents for TAKIMA tools TKJS-85
- Page 4 CONSERVE ESTE MANUAL 4. Mantenga a los niños alejados. Usted necesitará el manual para chequear Los niños nunca deben estar cerca del área las reglas de seguridad y precaución, de trabajo. No permita que ellos sostengan instrucciones de ensamble, procedimientos maquinas, herramientas o cables de extensión.
- Page 5 dispositivo de fijación o una mordaza para 18. Cheque las partes dañadas. mantener firme la pieza de trabajo. Mantenga Antes de continuar utilizando la maquina, el balance adecuado todo el tiempo sobre l o s p r o t e c t o r e s u o t r a s p a r t e s m ó v i l e s sus pies.
- Page 6 • Esta unidad debe utilizarse solamente como 21. Protección para oídos. Utilice protectores auriculares para trabajos que una herramienta de mano y nunca se le debe hagan ruidos superiores a 8db. forzar a trabajar en posición invertida, para 2 2 . T e n g a e n c u e n t a e l v o l t a j e d e l que ésta funcione como una caladora, a menos suministro de energía: Asegúrese de que el que se utilice con los accesorios destinados...
- Page 7 Safety Warnings for Jigsaws property damage or may cause an electric • Hold power tool by insulated gripping shock. surfaces, when performing an operation • Secure the workpiece. A workpiece clamped where the cutting accessory may contact with clamping devices or in a vice is held more hidden wiring or its own cord.
- Page 8 ESPECIFICACIONES Modelo TKJS-85 Product Features Voltaje 110V The numbering of the product features refers to Frecuencia 60Hz the illustration of the machine on the graphics Entrada Potencia 580W page. Velocidad 500-3000R/Min 2 Thumbwheel for stroke rate preselection Capacidad máxima de corte...
- Page 9 A loose saw blade can fall out and lead to Operating Modes • Before any work on the machine itself, pull injuries. the mains plug. For removal of the saw blade, proceed in Orbital Action Settings reverse order. Splinter Guard (see figure B) The four orbital action settings allow for optimal The splinter guard 14 (accessory) can prevent adaptation of cutting speed, cutting capacity...
- Page 10 Afterwards, push the base plate 8 to the stop Starting Operation • Observe correct mains voltage! The toward the mains cable. Tighten the screw 16 again. voltage of the power source must agree The splinter guard 14 can not be inserted for with the voltage specified on the nameplate mitre cuts.
- Page 11 Remove the saw blade from the machine and blade into the workpiece. When the base plate 8 fully lays on the allow the machine to cool down by running it for approx. 3 minutes at maximum stroke rate. workpiece, continue sawing along the desired Working Advice cutting line.
- Page 12 Clean the saw blade holder regularly. For this, remove the saw blade from the machine and lightly tap out the machine on a level surface. Heavy contamination of the machine can lead to malfunctions. Therefore, do not saw materials that produce a lot of dust from below or overhead.
- Page 13 Despiece Modelo: TKJS-85...
- Page 14 Lista de Partes Modelo: TKJS-85 Descripción Descripción Handle Counterweight Pan Head Screw Fork Lever Switch Shim Gear Self-Tapping Screw Needle Bearing Pan Head Screw Shim Cord Clamp Self-Tapping Screw Self-Tapping Screw Round Pin Cable Shield Round Pin Cord Gear Housing...
- Page 15 Lista de Partes Modelo: TKJS-85 Descripción Descripción Shim Soket Head Cap Wrench Flat Screw Screw Driver Shim Capacitance Bushing Reciprocating Lever Sets Round Pin (pcs) Retainer Ring Guide Wheel Discreteness Guide Wheel (pcs) Wheel Shelf Eccentric Cog Wheel Guide Wheel Shaft...