Table of Contents
Related Manuals for First Choice E Series
Summary of Contents for First Choice E Series
- Page 1 SPARE PARTS DIAGRAM FOR Pizza Oven E44 /E66 / E66-60 / E99 First Choice Group Blakeney Way, Kingswood Lakeside Cannock, Staffs, WS11 8LD TEL: 01543 577778 FAX: 01543504141 Email: enquires@firstchoice-cs.co.uk Web: www.firstchoice-cs.co.uk...
- Page 2 INSTRUCTIONS FOR USE AND MAINTENANCE ELECTRIC OVENS FOR PIZZA SERIES “E” ENGLISH Via delle Industrie 90, - 31030 Dosson di Casier (Tv) Italy - Tel. + 39 0422 634202 Fax +39 0422 634205...
-
Page 3: Declaration Of Ce Conformity
DECLARATION OF CE CONFORMITY Declares that the oven Complies with the requirements of the Directives: “Low Voltage Directive” 2006/95/EEC (Of the Council, dated 12 December 2006, on the approximation of the laws of the member States relating to electrical equipment destined to be used within given voltage limits) “Electromagnetic Compatibility Directive”... - Page 4 INDEX INDEX ..............................p. 4 1- “CE” DECLARATION OF CONFORMITY AND MARKING 1.1- Declaration of “CE” conformity ..................p. 3 1.2- “CE” marking ........................p. 5 2- GENERAL REMARKS 2.1- The importance of the manual ..................p. 5 2.2- Status of “turned off oven” .................... p. 6 2.3- Warranty ........................
-
Page 5: General Remarks
MARKING 1.2- “CE” MARKING The CE marking is a printed label (black color) applied as shown in FIG. 1. The plate bears in readable and indelible way the following data: - Name of the manufacturer; - Serial number (MATR); - CE marking; - Electric voltage and frequency (Volt/Hz);... -
Page 6: Warranty
2– GENERAL REMARKS 2.2- STATUS OF “TURNED OFF OVEN” Before performing any type of maintenance and/or adjustment intervention, it is compulsory to disconnect the power supply source, disconnecting the power supply plug from the mains outlet verifying that the oven is effectively turned off and cooled. 2.3- WARRANTY The manufacturer warrants that the concerned ovens are tested at manufacturer’s premises. -
Page 7: Technical Description
TECHNICAL DESCRIPTION -3 FIG. 3 and TAB. 1, in the related views, give the overall dimensions of the oven and of the baking chamber. Front side Left side FIG.3 (Dimensions of the oven and of the baking chamber) DIMENSIONS (mm) EXTERNAL BAKING CHAMBER MODELS... -
Page 8: Technical Data
3– TECHNICAL DESCRIPTION 3.3- TECHNICAL DATA TAB. 2 gives the technical data characterizing the different oven models. WEIGH BAKING ELECTRIC ELECTRIC ELECTRIC OPERATING BAKING MODELS CHAMBER VOLTAGE FREQUENCY POWER TEMPERATURE SURFACE (q.ty) (Hz) (kW) (°C) (material) (kg) MICRO MINI 78,5 Refractory 200/230/400 50/60... -
Page 9: Handling And Transport
HANDLING AND TRANSPORT 4.1- TRANSPORT AND LIFTING DURING THE LIFTING AND HANDLING PROCEDURES OF THE OVEN, MAKE SURE THAT WITHIN THE RANGE OF ACTION THERE ARE NOT PERSONS, ANIMALS OR THINGS WHOSE SAFETY MAY BE ACCIDENTALLY ENDANGERED. COMPULSORY USE LIFTING AND HANDLING MEANS AND SYSTEMS SUITABLE AND PROPER FOR THE WEIGHT AND THE SIZE OF THE OVEN (SEE PAR. - Page 10 4– HANDLING AND TRANSPORT 4.2- INSTRUCTION SHEET APPLIED ON THE PACKAGE Externally on the package, it is applied an instruction sheet for the handling of the same. (See Chap. 12 - ENCLOSURES). 4.3- POSITIONING ALL OVEN INSTALLATION PROCEDURES (POSITIONING AND ELECTRIC CONNECTION) MUST BE PERFORMED COMPULSORILY AND EXCLUSIVELY BY AUTHORIZED PERSONNEL SATISFYING THE TECHNICAL AND PROFESSIONALS REQUIREMENTS STATED, IN FULL COMPLIANCE WITH THE REGULATIONS IN FORCE IN THE COUNTRY OF USE OF THE OVEN.
-
Page 11: Installation
INSTALLATION -5 5.2- ELECTRIC CONNECTION The oven is supplied with a power supply cable located on the rear and without plug (FIG. 6 - Ref. 1). The electric data are given on the CE marking plate (FIG.1). THE ELECTRIC CONNECTION OF THE OVEN TO THE MAINS MUST BE PERFORMED COMPULSORILY AND EXCLUSIVELY BY AN AUTHORIZED TECHNICIAN (ELECTRICIAN) SATISFYING THE TECHNICAL AND PROFESSIONAL REQUIREMENTS STATED BY THE REGULATIONS IN FORCE IN THE COUNTRY OF USE OF THE OVEN, WHO MUST ISSUE A... -
Page 12: Personal Protection Equipment (Ppe)
6– SAFETY 6.1- REFERENCE DIRECTIVES AND STANDARDS The involved machine has been designed and manufactured considering the evaluations obtained by a careful risk analysis and trying to reach, considering the current status of the technique, the objec- tives preset by the essential safety and health requirements foreseen by the “New Approach Direc- tive”. -
Page 13: Control Panel
USE AND OPERATION -7 7.1- CONTROL PANEL The control panel is installed on the front side of the oven and changes according to the models as shown in FIG. 7. MOD. MICRO MOD. MOD. MOD. MINI 3 T MINI E4-E44 E6-E66 E6/60-E66/60 E9-E99... -
Page 14: First Commissioning
7- USE AND OPERATION 7.2– FIRST COMMISSIONING The first commissioning must be performed proceeding as follows: ONLY THE OPERATORS CHARGED WITH THE USE AND THE MAINTENANCE CAN PERFORM THE FIRST COMMISSIONING, THE TURNING ON AND THE MAINTENANCE OF THE OVEN. THE COMMISSIONING OF THE OVEN CAN BE PERFORMED ONLY WHEN THE INSTALLATION HAS BEEN COMPLETED AND THE AUTHORIZED TECHNICIANS HAVE ISSUED THE DECLA- RATION OF CONFORMITY FOR THE ELECTRIC CONNECTION. -
Page 15: Routine Maintenance
USE AND OPERATION -7 crown; 10) When baking has ended, open the door and extract the pizza and/or the pizzas and close the door again. 7.4- TURNING OFF OF THE OVEN Once the use of the oven has ended, proceed as follows: 1) Turn off the oven, bringing the thermostats (FIG. -
Page 16: General Warnings
8– MAINTENANCE ELECTRIC MAINTENANCE The eventual interventions are necessary only in case of failure of the electric components. All electric components can be reached on the right side of the oven, removing the panel with the aeration openings. REPLACEMENT OF THE CHAMBER LIGHT LAMP 1) Remove the panel with the aeration openings;... - Page 17 SPARE PARTS -10 TAB.1 MOD. E44 Ref. Quantity Name Frame for glasses Glass Gasket for glass Door Handle Handle grip in thermoplastic material Handle fixation group Door frame Façade Refractory stone 305 x 610 x 17 mm Resistances holder Left Panel Thermoinsulating material External sheating Terminal board...
- Page 18 SPARE PARTS -10 TAV. 1 MOD. E 44 Instructions for use and maintenance Rev. 11/2013 - EN...
- Page 19 SPARE PARTS -10 TAB.2 MOD. E66 Ref. Quantity Name Frame for glasses Glass Gasket for glass Door Handle Grip of handle in thermoplastic material Handle fixation group Door frame Façade Refractory stone 305 x 610 x 17 mm Resistances holding round element External sheathing Terminal board support Gasket...
- Page 20 SPARE PARTS -10 TAV. 2 MOD. E 66 Instructions for use and maintenance Rev. 11/2013 - EN...
- Page 21 SPARE PARTS -10 TAB.3 Mod. E66/60 Ref. Quantity Name Frame for glasses Glass Gasket for glass Door Handle Grip of handle in thermoplastic material Handle fixation group Door frame Façade Refractory stone 305 x 610 x 17 mm Resistances holding round element External sheathing Terminal board support Gasket...
- Page 22 SPARE PARTS -10 TAV. 3 MOD. E 66-60 Instructions for use and maintenance Rev. 11/2013 - EN...
- Page 23 SPARE PARTS -10 TAB.4 Mod. E/99 Ref. Quantity Name Frame for glasses Glass Gasket for glass Door Handle Grip of handle in thermoplastic material Handle fixation group Door frame Façade N° 8 Refractory stones 359x718x17 mm +N° 2 Refractory stones 359x359x17 mm Resistances holding round element External sheathing Terminal board support...
- Page 24 SPARE PARTS -10 TAV. 4 MOD. E 99 Instructions for use and maintenance Rev. 11/2013 - EN...
- Page 25 ELECTRIC PART -11 WIRING DIAGRAMS AND COMPONENTS MARK DESCRIPTION Room light switch Room light Base thermostat Ceiling thermostat Base light Ceiling light Base resistance Ceiling resistance Transformer Equipotential inlet Instructions for use and maintenance Rev. 11/2013 - EN...
-
Page 26: Wiring Diagrams
11- ELECTRIC PART WIRING DIAGRAMS 1 MOD. E44 / E66 Instructions for use and maintenance Rev. 11/2013 - EN... - Page 27 ELECTRIC PART -11 WIRING DIAGRAMS AND COMPONENTS MARK DESCRIPTION Room light switch Room light Base thermostat Ceiling thermostat Base light Ceiling light Base resistance Ceiling resistance Transformer Equipotential inlet Instructions for use and maintenance Rev. 11/2013 - EN...
- Page 28 11- ELECTRIC PART WIRING DIAGRAMS 2 MOD. E66/60 Instructions for use and maintenance Rev. 11/2013 - EN...
- Page 29 ELECTRIC PART -11 WIRING DIAGRAMS AND COMPONENTS MARK DESCRIPTION Room light switch Room light Base thermostat Ceiling thermostat Base light Ceiling light Base resistance Ceiling resistance Transformer Equipotential inlet Instructions for use and maintenance Rev. 11/2013 - EN...
- Page 30 11- ELECTRIC PART WIRING DIAGRAMS 3 MOD. E99 (230V) Instructions for use and maintenance Rev. 11/2013 - EN...
- Page 31 ELECTRIC PART -11 WIRING DIAGRAMS 4 MOD. E99 (400 V) Instructions for use and maintenance Rev. 11/2013 - EN...
- Page 32 ENCLOSERE -12 12.1- LIFTING INSTRUCTION SHEET APPLIED TO THE PACKAGE It is made of an adhesive sheet size A4 (210 x 297 mm) print b/w (Water resistant), applied externally to the carton box of the package (FIG.8). FIG.8 (LIFTING INSTRUCTION SHEET APPLIED TO THE PACKAGE) Instructions for use and maintenance Rev.
- Page 33 INFORMAZIONE AGLI UTENTI Ai sensi dell’art.13 del Decreto Legislativo 25 luglio 2005, n.151 “Attuazione Direttive 2002/95/CE, 2002/96/CE e 2003/108/CE, relative alla riduzione dell’uso di sostanze pericolose nelle apparecchia- apparecchiature elettriche ed elettroniche, nonché allo smaltimento dei rifiuti”. Il simbolo del cassonetto barrato riportato sull’apparecchiatura o sulla sua confezione indica che il prodotto alla fine della propria vita utile deve essere raccolto separatamente dagli altri rifiuti.