Advertisement
Available languages
Available languages
"live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
Safety instructions when using long drill bits
Never operate at higher speed than the maximum
u
speed rating of the drill bit. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
Always start drilling at low speed and with the bit tip
u
in contact with the workpiece. At higher speeds, the bit
is likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do
u
not apply excessive pressure.Bits can bend causing
breakage or loss of control, resulting in personal injury.
Additional safety warnings
Switch the power tool off immediately if the applica-
u
tion tool becomes blocked. Be prepared for high
torque reactions which cause kickback. The applica-
tion tool becomes blocked when it becomes jammed in
the workpiece or when the power tool becomes over-
loaded.
Hold the power tool securely. When tightening and
u
loosening screws be prepared for temporarily high torque
reactions.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Bosch Power Tools
Protect the power tool against heat, e.g.
against continuous intense sunlight, fire,
water, and moisture. There is a risk of explo-
sion.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
fire and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for tightening and loosening
screws, as well as for drilling in wood, metal and plastic and
for impact drilling in brick and masonry.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1)
Tool holder
(2)
Keyless chuck
(3)
Torque presetting ring
(4)
Operating mode presetting ring
(5)
Gear selector switch
A)
(6)
Battery release button
A)
(7)
Battery
(8)
Rotational direction switch
(9)
On/off switch
English | 13
Read all the safety and
general instructions. Fail-
ure to observe the safety
and general instructions
may result in electric shock,
1 609 92A 5L3 | (15.01.2020)
Hide quick links:
Advertisement
