Subscribe to Our Youtube Channel
Related Manuals for ADIATEK QUARTZ 50
Summary of Contents for ADIATEK QUARTZ 50
- Page 1 50 03 2020 Use and maintenance Warning! Please read the instructions before use.
-
Page 3: Table Of Contents
INTRODUCTORY COMMENT Thank you for having chosen our machine. This floor cleaning machine is used for the industrial and civil cleaning and is able to clean any type of floor. During its advance movement, the combined action of the brushes and the detergent solution removes the dirt which is aspirated through the rear suction assembly, giving a perfectly dry surface. -
Page 4: General Rules Of Safety
GENERAL RULES OF SAFETY MAINTENANCE The rules below have to be followed carefully in order to avoid If the machine does not work properly, check by conducting simple injury to the operator and damage to the machine. maintenance procedures. Otherwise, as for technical advice from an Read the labels carefully on the machine. -
Page 5: Technical Description
TECHNICAL DESCRIPTION Working width Squeegee width Work capacity up to 2032 Brush diameter Brush rpm Brush pressure Brush motor Suction motor Suction motor depression mbar Traction motor Drive type automatic Maximum gradient Solution tank Recovery tank Machine length 1220 Machine height Machine width (without squeegee) Machine weight (empty tanks, without batteries) Machine gross weight (in conformity with the EN 60335-2-72 art. -
Page 6: Display And Controls Legend
DISPLAY AND CONTROLS LEGEND DISPLAY CLEANING MODE SELECTION BUTTON: • AUTOMATIC • MANUAL • BREAK WASHING WORKING MODE SELECTION BUTTON • STANDARD • • UP/DOWN AND UNLOCK, BRUSH BASE BUTTON SUCTION MOTOR BUTTON • ON/OFF • SILENT MODE OPEN/CLOSE SOLENOID VALVE SOLUTION LEVEL BUTTON (ONLY FOR 3S/3SD) MAXIMUM SPEED INCREASE BUTTON MAXIMUM SPEED DECREASE BUTTON... -
Page 7: Reading The Display
READING THE DISPLAY DISPLAY WHEN SWITCHING ON When the machine is switched on the display shows the following screen. The next screen shows: BATTERY SETTINGS Gel batteries setting HOURMETER AGM batteries setting SOFTWARE RELEASE Lead/acid batteries setting Display card Check card WATER SYSTEM (empty field if standard) XFC batteries setting... -
Page 8: Navigation Controls
NAVIGATION CONTROLS SCROLL UP INCREASE CONFIRM SCROLL DOWN DECREASE GENERAL SETTINGS CHANGE THE WATER SYSTEM To enter the settings menu, use the dashboard buttons and proceed as Once entered the general settings it is possible to set the type of water follows: system which the machine is provided of (standard, 3S, 3SD, O3, O3+3S, 1. -
Page 9: Manual Symbols
MANUAL SYMBOLS Open book stmbol. Indicates that the operator has to read the manual Obligation symbol requiring to wear the safety before the use of the machine. glasses. Open book symbol. For the proper functioning of the on-board battery Obligation symbol requiring to wear the safety recharger (optional), read the manual of the gloves. -
Page 10: Before The Use
BEFORE THE USE equipment (due to weight, considering the type of batteries chosen, and coupling system). HANDLING OF THE PACKED MACHINE The batteries must be in accordance with CEI 21-5 Norms. The machine is supplied with suitable packing foreseen for fork lift truck handling. -
Page 11: Lifting The Recovery Tank
LIFTING THE RECOVERY TANK For some ordinary maintenance operations, like the battery charge, it could be necessary to open the recovery tank. Grab the handles (1) and lift it. Open it to its maximum extension in order to lock the opening system.. Move the lever (2) to unlock it, then close the tank keeping a hand on the handle (1). -
Page 12: Floor Cleaning
FLOOR CLEANING CONNECTING THE BATTERY CONNECTOR AND SWITCHING ON THE Always use a foam-controlled detergent. To safely avoid the production MACHINE of foam, before starting to work, add also a small amount of anti-foam Once that the battery charging has been completed: solution in the recovery tank. -
Page 13: Water Carriage Level Selection - 3S And 3Sd System
WORK WATER CARRIAGE LEVEL SELECTION – 3S AND 3SD SYSTEM Pressing the level selection button (1), the H value can be adjusted from H1 to H7. A safety device prevents the machine’s movement if the operator is not properly placed on the footboard. To turn on the machine: 1. -
Page 14: Speed Adjustment, Forward And Backward
AUTOMATIC MODE WORK 1. Automatic mode is helpful to ease the operator work. 2. Check that the machine is set in automatic mode, if not press button (1) and the display will show the corresponding symbol. 6. While running the first meters check that the squeegee adjustment guarantees a perfect drying action and that the detergent solution flow is appropriate. -
Page 15: Horn
HORN The machine is provided with a horn that can be activated pressing button (1). PARKING BRAKE The machine is equipped with a parking brake on the traction motor wheel that operates at the complete release of the pedal or when the machine is without batteries. -
Page 16: Machine Stop After Cleaning Operation
MACHINE STOP AFTER CLEANING OPERATION DAILY MAINTENANCE BREAK WASHING MODE DRAINING AND CLEANING THE RECOVERY TANK IN AUTOMATIC OR MANUAL WORKING MODE: 1. At the end of the washing 1. Hold the exhaust hose placed on the front part of the machine cycle, keeping the button (1) after having taken it off from pressed, the functioning of... -
Page 17: Cleaning The Brush
1. With the brush base lifted, rotate the squeegee on one side. 2. With the squeegee in such position, take off the squeegee hose coupling (1). 4. Turn off the machine.. Do not wash the hose that goes from the suction motor to the CLEANING THE BRUSH recovery tank. -
Page 18: Two-Monthly Maintenance
TWO-MONTHLY MAINTENANCE THE SUCTION MOTOR DOES NOT WORK FRONT SQUEEGEE RUBBER CHECK 1. Check the battery charge on the display. 2. Check on the display that the starting signal of the Check the wear of the squeegee rubber and eventually replace it. suction motor is on. -
Page 19: The Machine Does Not Clean Properly
THE SQUEEGEE DOES NOT DRY PROPERLY If the problem persists, please contact the authorized technical assistance. 1. Check that the squeegee rubbers are clean. 2. Check the adjustment of the height and the inclination of the THE MACHINE DOES NOT CLEAN PROPERLY squeegee (see section “ADJUSTMENT OF THE SQUEEGEE”...
Need help?
Do you have a question about the QUARTZ 50 and is the answer not in the manual?
Questions and answers