Telguard Digital TG-4 Quick Installation Manual

INCOMING
TELCO
ANTENNA
PREMISE
PHONE
4 5
3 6
R T
2 7 LED MODE SELECT
1 8
RJ31X
J10
WARNING: TELGUARD
HIGH VOLTAGE
Digital TG-4
PRESENT ON PHONE
LINES.
DISCONNECT PRIOR T J7
TO SERVICING.
BATTERY
(12V)
STC1
J6
(N.O.)
R
STC2
SYSTEM TROUBLE,
(N.C.)
STC (LED #2)
1 FLASH = AC LOW/MISSING
2 FLASH = LBC LOW BATTERY
EARTH
3 FLASH = LFC LINE FAULT
GROUND
4 FLASH = NSC NO SERVICE
5 FLASH = RFC RADIO FAILURE
6 FLASH = DTF DIAL TONE FAIL
CAUTION:
REGISTRATION
INCORRECT CONNECTIONS
MAY RESULT IN DAMAGE TO UNIT.
(LED #1)
ON = UNIT REGISTERED
OFF = UNIT NOT REGISTERED
If flashing with LED 4 = DENIED ,
(NACK) www.Telguard.com
Call Technical Support.
REFER TO INSTALLATION AND OPERATING
If all LED's flashing = NO RESPONSE,
INSTRUCTIONS MANUAL. THIS DEVICE COMPLIES
Check Signal Strength.
WITH FCC RULES PART 68 AND 15.
SYSTEM STATUS LEDS
RSSI MODE
RSSI Value LED's Lighted RF dBm
NO SVC LED 5*= flash, 4-2 = off n/a
1 LED 5 = on, 4-2 = off < -111 dBm
1 ½ LED 5 = on, 4 = flash, 3-2 = off > -110 dBm
2 LED 5-4 = on, 3-2 = off > -100 dBm
2 ½ > -90 dBm
LED 5-4 = on, 3 = flash, 2 = off
(Minimum Signal Recommended)
3 LED 5-3 = on, 2 = off > -80 dBm
3 ½ LED 5-3 = on , 2 = flash > -70 dBm
4 LED 5-2 = on > -60 dBm
*Note: LED 1 ON INDICATES MORE THAN ONE TOWER
SYSTEM STATUS LEDS
OPEN = NORMAL
SHORTED = RSSI
NORMAL MODE
LED #5 GREEN
ON = RADIO INITIALIZING
FLASH = COMMUNICATING
1
LED #4 RED
SIGNAL
2
ON = WAITING FOR RESPONSE
STRENGTH 3
If flashing with LED 1 = DENIED
(NACK)
LEDS 4
LED #3 YELLOW
5
ON = MODE 1 (TELCO Primary)
OFF = MODE 2 (CELL Primary)
FLASH = C/C OFF HOOK CELL
LED #2 RED
SYSTEM TROUBLE, STC
(See Table)
LED #1 GREEN
REGISTRATION (See Table)
TELCO DIALER
AC
LED 6
BLANK PIN
AC
(12V 800MA)
HOST C/C
1 2 3 4 5 6 7 8 9
24 HOUR ZONE (N.O.)
24 HOUR ZONE (N.C.)
TELULAR CORPORATION
420 Thornton Road, Suite 109
Lithia Springs, GA 30122
(800) 229-2326 Fax: 678-945-1651
Telguard Digital
QUICK INSTALLATION GUIDE
Installation Summary
There are six steps in installing Telguard properly. IF YOU DO NOT
PROCEED IN THE ORDER AND MANNER PRESCRIBED, YOU MAY
NOT COMPLETE THE INSTALLATION IN THE TIME ALLOCATED.
S 1: R C
TEP EGISTER FOR ELLULAR
Complete the Activation Form online at
form to Telular Cellular Service prior to leaving for the job site. Telular
requires this information to register and activate the unit.
S 2: L U M
TEP OCATE NIT AND
First, you will be confirming that Telguard has adequate cellular signal strength. Put
J10 across both pins, LEDS will now indicate signal strength, minimum
recommended is 2 ½ (2 on solid and the third flashing).
S 3: T C/C A
TEP RANSMIT LARMS OVER THE
Once you have confirmed that the unit is active, you will be ready to verify that the
C/C is programmed properly. This step is important to verify that the C/C is
programmed with valid account code and central station information before
transmitting signals through the cellular network.
S 4: P , A
TEP ROGRAM CTIVATE
C R N
THE ELLULAR ADIO ETWORK
Next, you will be connecting the C/C's digital dialer output to Telguard and verifying
that alarm signals can be reliably sent through Telguard over cellular to the central
station digital receiver. The incoming Telco line is not connected to Telguard during
this step. A minimum of two alarm signals must be transmitted.
(NOTE:
THE FIRST ALARM WILL REGISTER THE UNIT WITH THE
C C ,
OMMUNICATION ENTER IT WILL NOT GO TO THE
SIGNALS AFTER THE FIRST ARE SENT TO THE
S 5: C S
TEP ONNECT UPERVISORY
Next, you will wire Telguard's supervisory trip outputs to the C/C and then test.
S 6: C I
TEP OMPLETE THE NSTALLATION
Your last step will be to check the jumper setting of J10 (LED mode, open =
normal), attach earth ground, and permanently mount the unit.
TG-4
model
S
ERVICE
www.Telguard.com or fax the
S S (RSSI)
EASURE IGNAL TRENGTH
T C
ELCO ONNECTION
& T C/C A
RANSMIT LARMS OVER
T
ELULAR
C ,
ENTRAL STATION
C S )
ENTRAL TATION
T O
RIP UTPUTS
56033604
ALL