Telguard Digital TG-4 Quick Installation Manual

INCOMING
TELCO
ANTENNA
PREMISE
PHONE
4 5
3 6
R T
2 7
1 8
RJ31X
WARNING:
HIGH VOLTAGE
PRESENT ON PHONE
LINES.
DISCONNECT PRIOR T J7
TO SERVICING.
BATTERY
STC1
J6
(N.O.)
R
STC2
SYSTEM TROUBLE,
(N.C.)
STC (LED #2)
1 FLASH = AC LOW/MISSING
2 FLASH = LBC LOW BATTERY
EARTH
3 FLASH = LFC LINE FAULT
GROUND
4 FLASH = NSC NO SERVICE
5 FLASH = RFC RADIO FAILURE
6 FLASH = DTF DIAL TONE FAIL
CAUTION:
REGISTRATION
INCORRECT CONNECTIONS
MAY RESULT IN DAMAGE TO UNIT.
(LED #1)
ON = UNIT REGISTERED
OFF = UNIT NOT REGISTERED
If flashing with LED #4 = DENIED ,
(NACK)
Call Technical Support.
If all LED's flashing = NO RESPONSE,
Check Signal Strength.
www.Telguard.com
REFER TO INSTALLATION AND OPERATING INSTRUCTIONS MANUAL.
THIS DEVICE COMPLIES WITH FCC RULES PART 68 AND 15.
SYSTEM STATUS LEDS
RSSI MODE
RSSI Value LED's Lighted RF dBm
NO SVC LED 5*= flash, 4-2 = off
1 LED 5 = on, 4-2 = off < -111 dBm
1 ½ LED 5 = on, 4 = flash, 3-2 = off > -110 dBm
2 LED 5-4 = on, 3-2 = off > -100 dBm
2 ½ > -90 dBm
LED 5-4 = on, 3 = flash, 2 = off
(Minimum Signal Recommended)
3 LED 5-3 = on, 2 = off > -80 dBm
3 ½ LED 5-3 = on , 2 = flash > -70 dBm
4 LED 5-2 = on > -60 dBm
*Note: LED #1 ON INDICATES MORE THAN ONE TOWER
LED MODE SELECT
SYSTEM STATUS LEDS
OPEN = NORMAL
NORMAL MODE
SHORTED = RSSI
LED #1 GREEN
J10
REGISTRATION (See Table)
1
LED #2 RED
SIGNAL
2
SYSTEM TROUBLE, STC (See Table)
STRENGTH 3
LED #3 YELLOW
4
LEDS ON = MODE 1 (TELCO Primary)
5
OFF = MODE 2 (CELL Primary)
FLASH = C/C OFF HOOK CELL
LED #4 RED
ON = WAITING FOR RESPONSE
If flashing with LED #1 = DENIED(NACK)
LED #5 GREEN
ON = RADIO INITIALIZING
FLASH = COMMUNICATING
TELGUARD
Digital TG-4
TELCO DIALER
AC
LED 6
(12V)
BLANK PIN
AC
(12V 800MA)
HOST C/C
1 2 3 4 5 6 7 8 9
24 HOUR ZONE (N.O.)
24 HOUR ZONE (N.C.)
TELULAR CORPORATION
420 Thornton Road, Suite 109
Lithia Springs, GA 30122
(800) 229-2326
Fax: 678-945-1651
Telguard Digital

QUICK INSTALLATION GUIDE

Installation Summary

n/a
There are six steps in installing Telguard properly. IF YOU DO NOT
PROCEED IN THE ORDER AND MANNER PRESCRIBED, YOU MAY
NOT COMPLETE THE INSTALLATION IN THE TIME ALLOCATED.
S 1: R
TEP EGISTER FOR
Complete the Activation Form online at
the form to Telular Cellular Service prior to leaving for the job site.
Telular requires this information to register and activate the unit.
S 2: L
TEP OCATE
Second, you will be confirming that Telguard has adequate cellular signal
strength. Put J10 across both pins, LEDS will now indicate signal strength,
minimum recommended is 2 ½ (2 on solid and the third flashing).
S 3: T
TEP RANSMIT
Connect C/C and telco line to the Telguard. Trip a simple alarm on the C/C
and transmit over the telco line. This step is important to verify that the C/C
is programmed with valid account code and central station information
before transmitting signals through the cellular network.
S 4: P
TEP ROGRAM
C
THE ELLULAR
Next, you will be programming the Telguard unless the default settings are
what you want. Then connect the C/C's digital dialer output to Telguard and
verify that alarm signals can be reliably sent over cellular to the central
station digital receiver. The incoming telco line is not connected to Telguard
during this step. A minimum of two alarm signals must be transmitted.
(NOTE:
ACTIVATE THE UNIT WITH THE
IT WILL NOT BE TRANSMITTED TO THE
SIGNALS AFTER THE FIRST ARE SENT TO THE
S 5: C
TEP ONNECT
Next, you will wire Telguard's supervisory trip outputs to the C/C and then test.
S 6: C
TEP OMPLETE THE
Your last step will be to check the jumper setting of J10 (LED mode, open =
normal), attach earth ground, and permanently mount the unit.
C S
ELLULAR ERVICE
www.Telguard.com
U M S
NIT AND EASURE IGNAL
C/C A
LARMS OVER THE
, A & T
CTIVATE RANSMIT
R N
ADIO ETWORK
THE FIRST ALARM WILL CONFIRM REGISTRATION AND
T C
ELULAR OMMUNICATION
C
ENTRAL STATION
S T O
UPERVISORY RIP UTPUTS
I
NSTALLATION
TG-4
model
or fax
S (RSSI)
TRENGTH
T C
ELCO ONNECTION
C/C A
LARMS OVER
C .
ENTER
.
ALL
C S .)
ENTRAL TATION
56033603