Ratek SWB10D Water Bath - Operating Manual
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
The use of flammable liquids may cause serious injury or danger to life.
CAUTION
CAUTION
CAUTION
CAUTION
Always work above the level of the water bath to avoid spillage of dangerously hot water. At no point
should the user, operator, animal or any other perishable object be situated directly beneath the water
bath.
-
ALWAYS wear protective eyewear when working with hot liquids.
ALWAYS
ALWAYS
ALWAYS
-
ALWAYS
ALWAYS place the water bath on a strong, even, dry, flat waterproof surface which is made of
ALWAYS
ALWAYS
inflammable material. Placing the water bath on an unstable surface could cause hot water to spill.
-
ALWAYS empty the water bath before moving the equipment to a new location.
ALWAYS
ALWAYS
ALWAYS
-
ALWAYS
ALWAYS turn off both mains power switches (elements 6 and 8 in Figure 1) when the unit is not in
ALWAYS
ALWAYS
operation and turn off the mains power supply at the outlet.
-
ALWAYS turn off both mains power switches (elements 6 and 8 in Figure 1) and unplug the
ALWAYS
ALWAYS
ALWAYS
equipment from the mains power supply outlet before emptying the water tank or moving the
equipment.
-
ALWAYS
ALWAYS be careful of water condensation above or near the water bath and ensure at all times
ALWAYS
ALWAYS
that the condensation cannot come in contact with the water bath control panel or mains power
input receptacle (element 10 in Figure 1). Ensure benches are kept dry at all times.
-
ALWAYS
ALWAYS
ALWAYS
ALWAYS operate the water bath in a well ventilated area with adequate clearance around the water
bath as indicated.
-
ALWAYS
ALWAYS be careful of steam and avoid making contact.
ALWAYS
ALWAYS
-
ALWAYS use the water bath with the oscillating cradle moving to improve temperature uniformity
ALWAYS use the water bath with the oscillating cradle moving t
ALWAYS use the water bath with the oscillating cradle moving t
ALWAYS use the water bath with the oscillating cradle moving t
-
ALWAYS
ALWAYS use only the supplied mains power lead. Non-genuine leads may not be suitable.
ALWAYS
ALWAYS
-
NEVER operate the water bath without water in the water tank.
NEVER operate the water bath without water in the water tank.
NEVER operate the water bath without water in the water tank.
NEVER operate the water bath without water in the water tank.
-
NEVER empty the water bath while it contains hot water. Always allow the water to cool to ambient
NEVER
NEVER
NEVER
room temperature before emptying.
-
NEVER operate the equipment if you believe it is damaged in any way.
NEVER
NEVER
NEVER
-
NEVER
NEVER operate the water bath if the mains power supply cable is damaged in any way
NEVER
NEVER
-
NEVER use any sharp or metal objects near the water bath control panel or mains power input
NEVER
NEVER
NEVER
receptacle (element 10 in Figure 1).
-
NEVER lift the water bath if you have an existing injury that impairs your ability to lift.
NEVER
NEVER
NEVER
Preparation & Installation
Preparation & Installation
Preparation & Installation
Preparation & Installation
The water bath should be installed and operated in strict accordance with the following instructions.
CAUTION
CAUTION
CAUTION
CAUTION
The water bath is not for use in explosive atmospheres as there is a risk of fire, explosion, burns or
scalding present under these conditions.
CAUTION
CAUTION
CAUTION
CAUTION
Be careful when lifting and observe your local operational health and safety requirements for lifting
before unpacking the carton.
Unpacking and Installing
Unpacking and Installing
Unpacking and Installing
Unpacking and Installing
- Carefully remove all packaging material from the water bath, as well as the supplied mains power
lead, User Manual and any other supplied accessories. The oscillating cradle (element 9 in Figure 1)
inside the water bath should not be removed
- Carefully inspect the water bath, mains power lead and all packaging for any signs of damage. If any
signs of damage are present, do not
equipment if you have a received a damaged product.
- Place the water bath in an upright position as per Figure 1 on a strong, even, flat waterproof surface
which is made of inflammable material.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
should not be removed. . . .
should not be removed
should not be removed
do not install or operate the equipment. Contact the supplier of your
do not
do not
Page 9 of 24
o improve temperature uniformity
o improve temperature uniformity. . . .
o improve temperature uniformity
Need help?
Do you have a question about the SWB10D240 and is the answer not in the manual?