Page 4
We acknowledge the right of proprietors of trademarks mentioned in this book. The information in this document is subject to change without notice. Bull will not be liable for errors contained herein, or for incidental or consequential damages in connection with the use of this material.
Contents Safety notices ....... . . v PCI adapter placement for the 31E/2B, 31E/1C, or 31E/2C ....1 Supported PCI adapters for the 31E/2B, 31E/1C, or 31E/2C .
Page 6
PCI adapter placement for the 31E/2B, 31E/1C, or 31E/2C...
Safety notices Safety notices may be printed throughout this guide. v DANGER notices call attention to a situation that is potentially lethal or extremely hazardous to people. v CAUTION notices call attention to a situation that is potentially hazardous to people because of some existing condition.
Page 8
DANGER When working on or around the system, observe the following precautions: Electrical voltage and current from power, telephone, and communication cables are hazardous. To avoid a shock hazard: v Connect power to this unit only with the provided power cord. Do not use the provided power cord for any other product.
Page 9
Observe the following precautions when working on or around your IT rack system: v Heavy equipment–personal injury or equipment damage might result if mishandled. v Always lower the leveling pads on the rack cabinet. v Always install stabilizer brackets on the rack cabinet. v To avoid hazardous conditions due to uneven mechanical loading, always install the heaviest devices in the bottom of the rack cabinet.
Page 10
CAUTION: Removing components from the upper positions in the rack cabinet improves rack stability during relocation. Follow these general guidelines whenever you relocate a populated rack cabinet within a room or building: v Reduce the weight of the rack cabinet by removing equipment starting at the top of the rack cabinet.
Page 11
(L003) All lasers are certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for class 1 laser products. Outside the U.S., they are certified to be in compliance with IEC 60825 as a class 1 laser product.
Page 12
CAUTION: Data processing environments can contain equipment transmitting on system links with laser modules that operate at greater than Class 1 power levels. For this reason, never look into the end of an optical fiber cable or open receptacle. (C027) CAUTION: This product contains a Class 1M laser.
PCI adapter placement for the 31E/2B, 31E/1C, or 31E/2C Find information about the peripheral component interconnect (PCI), PCI-X, and PCI Express (PCIe) adapters that are supported for the 7/10 (31E/1C) and 7/30 (31E/2B and 31E/2C) systems. The following features are electromagnetic compatibility (EMC) Class B features. See the Class B Notices in the Hardware Notices area.
Page 14
Table 2. PCIe adapters supported on the AIX, , or Linux operating system (continued) System Feature code /CCIN Description 31E/2C 5289 PCIe 2-port Async EIA-232 PCIe 1X LPC Adapter (FC 5289) v Short, x8, full-height adapter v PCIe 1.1 v 2 Ports through RJ45 by using the DB9 connector v EIA-232 Compatible v OS support: AIX and Linux 31E/2B, 31E/1C, and 31E/2C 5290...
Page 15
Table 2. PCIe adapters supported on the AIX, , or Linux operating system (continued) System Feature code /CCIN Description 31E/2C 5735 8-Gigabit PCI Express Dual Port Fibre Channel Adapter (FC 5735) v Short, x8 v Extra-high bandwidth: If only one port is planned to be active in normal operation, the adapter is counted as an extra-high bandwidth adapter.
Page 16
Table 2. PCIe adapters supported on the AIX, , or Linux operating system (continued) System Feature code /CCIN Description 31E/2B, 31E/1C, and 31E/2C 5269 POWER GXT145 PCI Express Graphics Accelerator (FC 5269) v Low-profile adapter v Short, x1 v OS support: AIX and Linux 31E/2B, 31E/1C, and 31E/2C 5270 10Gb FCoE PCIe Dual Port Adapter (FC 5270) v Low-profile adapter...
Page 17
Table 2. PCIe adapters supported on the AIX, , or Linux operating system (continued) System Feature code /CCIN Description 31E/1C and 31E/2C 5280 PCIe2 LP 2x10GbE SR 2x1GbE UTP Adapter (FC 5280) v Low-profile, short, x8 v PCIe 2 v OS support: Linux 31E/2B, 31E/1C, and 31E/2C 5281 1Gb Ethernet UTP 2-port PCIe Adapter (FC 5281) v Low-profile, short, x8...
Page 18
Table 2. PCIe adapters supported on the AIX, , or Linux operating system (continued) System Feature code /CCIN Description 31E/2C 5768 2-Port Gigabit Ethernet-SX PCI Express Adapter (FC 5768) v Short, x4 v High bandwidth v OS support: AIX, , and Linux 31E/2C 5769 10 Gigabit Ethernet-SR PCI Express Adapter (FC...
Table 2. PCIe adapters supported on the AIX, , or Linux operating system (continued) System Feature code /CCIN Description 31E/1C and 31E/2C 5283 PCIe2 LP 2-Port 4X InfiniBand QDR Adapter (FC 5283) v Generation-2 low-profile adapter v Extra-high bandwidth v Requires available PCIe slot in the FC 5685 PCIe Riser Card (generation-2) v OS support: AIX and Linux 31E/1C and 31E/2C...
Page 20
Figure 1. Rear view of the 31E/2B with location codes for the PCI slots Table 3. PCI slot locations and descriptions Slot Location code Description Adapter size Slot 1 P1-C3 PCIe x8 PCIe PHB0 module A Low-profile Slot 2 P1-C4 PCIe x8 PCIe PHB1 module A Low-profile...
Page 21
Table 4. Adapter slot priorities and maximums for PCIe adapters (continued) Maximum number of adapters supported per Feature code Description system 5290 PCIe LP 2-port Async EIA-232 Adapter (FC 5290) v Low-profile adapter v PCIe 1.1 v Short, x8 v 2 Ports through RJ45 by using the DB9 connector v EIA-232 compatible v OS support: AIX and Linux 5273...
Table 4. Adapter slot priorities and maximums for PCIe adapters (continued) Maximum number of adapters supported per Feature code Description system 5275 10 Gigabit Ethernet-SR PCI Express Adapter (FC 5275) v Low-profile adapter v Short, x8 v OS support: AIX and Linux 5281 1Gb Ethernet UTP 2-port PCIe Adapter (FC 5281) v Low-profile, short, x8...
Page 23
slots. All slots in this system are low-profile slots only. Each PCIe is a separate PCI host bridge (PHB). The PCIe slot 1 and slot 4 have an x16 connector and the other slots have an x8 connector. For the information about the maximum adapters supported on your system, see Table 6. Figure 2.
Page 24
Table 6. Adapter slot priorities and maximums for PCIe adapters (continued) Maximum number Feature of adapters code Description Slot priorities supported 5290 PCIe LP 2-port Async EIA-232 Adapter (FC 5290) 1, 2, 3, 4, 5, 6 v Low-profile adapter v PCIe 1.1 v Short, x8 v 2 Ports through RJ45 by using the DB9 connector v EIA-232 compatible...
Page 25
Table 6. Adapter slot priorities and maximums for PCIe adapters (continued) Maximum number Feature of adapters code Description Slot priorities supported 5271 4-Port 10/100/1000 Base-TX PCI Express Adapter (FC 1, 2, 3, 4, 5, 6 5271) v Low-profile adapter v Short, x4 v OS support: AIX and Linux 5272 10 Gigabit Ethernet-CX4 PCI Express Adapter (FC 5272)
Page 26
Table 6. Adapter slot priorities and maximums for PCIe adapters (continued) Maximum number Feature of adapters code Description Slot priorities supported 5284 PCIe2 LP 2-port 10GbE SR Adapter (FC 5284) 1, 2, 3, 4, 5, 6 v Generation-2, low-profile capable, high-performance adapter v Capable of transferring data to a distance of 300 m over MMF-850 nm fiber cable...
one type of GX++ adapter, feature code (FC) EJ0H (GX++ LP 1-port PCIe2 x8 adapter). When plugging in these adapters, if only one adapter is being configured it must be placed in the GX++ slot 2. This placement helps distribute the I/O traffic over the GX buses to the processors. PCI adapter placement rules and slot priorities for the 31E/2C Some adapters must be placed in specific PCI Express (PCIe) slots to function correctly or to perform optimally.
Page 28
Table 7. PCI slot locations and descriptions (continued) Slot Location code Description Adapter size Slot 1, slot 5, and slot 6 availability: If the 2-Port 12X InfiniBand2 adapter (feature code (FC) EJ0G) is installed in GX++ slot 2 in the 31E/2C system, slot 6 (P1-C7), slot 5 (P1-C6), and slot 1 (P1-C2) are not available to install any PCI adapter.
Page 29
Table 8. Adapter slot priorities and maximums for PCIe adapters (continued) Maximum number Feature of adapters code Description Slot priorities supported 2053 PCIe RAID and SSD SAS Adapter 3Gb Low-profile (FC 1, 2, 3, 4, 5, 6 2053) v Low-profile adapter, requires two slots v Short, x8 v OS support: AIX, , and Linux v VIOS attachment requires version 2.2, or later...
Page 30
Table 8. Adapter slot priorities and maximums for PCIe adapters (continued) Maximum number Feature of adapters code Description Slot priorities supported 5269 POWER GXT145 PCI Express Graphics Accelerator (FC 1, 2, 3, 4, 5 5269) v Low-profile adapter v Short, x1 v OS support: AIX and Linux 5748 POWER GXT145 PCI Express Graphics Accelerator (FC...
Page 31
Table 8. Adapter slot priorities and maximums for PCIe adapters (continued) Maximum number Feature of adapters code Description Slot priorities supported 5276 4-Gigabit PCI Express Dual Port Fibre Channel Adapter 1, 2, 3, 4, 5, 6 (FC 5276) v Low-profile adapter v Short, x4 v OS support: AIX, , and Linux 5278...
Page 32
Table 8. Adapter slot priorities and maximums for PCIe adapters (continued) Maximum number Feature of adapters code Description Slot priorities supported 5717 4-Port 10/100/1000 Base-TX PCI Express Adapter (FC 1, 2, 3, 4, 5, 6 5717) v Short, x4 v High bandwidth v OS support: AIX and Linux 5732 10 Gigabit Ethernet-CX4 PCI Express Adapter (FC 5732)
Table 8. Adapter slot priorities and maximums for PCIe adapters (continued) Maximum number Feature of adapters code Description Slot priorities supported 2728 4-Port USB PCIe Adapter (FC 2728) 1, 2, 3, 4, 5, 6 v Low-profile adapter v Single-slot, half-length PCIe adapter v PCIe 1.1 v OS support: AIX and Linux 4808...
PCI adapters slot priorities for the 58/02 and 58/77 expansion units Learn about the PCI Express (PCIe) slots in the 58/02 and 58/77 expansion units. System description The 58/02 and 58/77 expansion units are 19-inch, rack-mountable, I/O expansion drawers that are designed to be attached to the system using 12x double date rate (DDR) cables.
Page 35
For best performance, fill P1-C1, P1-C4, P1-C2, P1-C5, P1-C3, and P1-C6 first with the highest bandwidth adapters. Then fill the remaining slots. PCI adapter placement...
Page 36
PCI adapter placement for the 31E/2B, 31E/1C, or 31E/2C...
Notices This information was developed for products and services offered in the U.S.A. The manufacturer may not offer the products, services, or features discussed in this document in other countries. Consult the manufacturer's representative for information on the products and services currently available in your area.
This information is for planning purposes only. The information herein is subject to change before the products described become available. This information contains examples of data and reports used in daily business operations. To illustrate them as completely as possible, the examples include the names of individuals, companies, brands, and products.
Page 39
Federal Communications Commission (FCC) statement Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Page 40
VCCI Statement - Japan The following is a summary of the VCCI Japanese statement in the box above: This is a Class A product based on the standard of the VCCI Council. If this equipment is used in a domestic environment, radio interference may occur, in which case, the user may be required to take corrective actions.
Page 41
Electromagnetic Interference (EMI) Statement - Taiwan The following is a summary of the EMI Taiwan statement above. Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user will be required to take adequate measures. Electromagnetic Interference (EMI) Statement - Korea Germany Compliance Statement Deutschsprachiger EU Hinweis: Hinweis für Geräte der Klasse A EU-Richtlinie zur...
Zulassungsbescheinigung laut dem Deutschen Gesetz über die elektromagnetische Verträglichkeit von Geräten (EMVG) (bzw. der EMC EG Richtlinie 2004/108/EG) für Geräte der Klasse A Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das EG-Konformitätszeichen - CE - zu führen. Verantwortlich für die Einhaltung der EMV Vorschriften ist der Hersteller: International Business Machines Corp.
Page 43
v Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. v Consult an IBM-authorized dealer or service representative for help. Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits.
Page 44
Japanese Electronics and Information Technology Industries Association (JEITA) Confirmed Harmonics Guideline with Modifications (products greater than 20 A per phase) Electromagnetic Interference (EMI) Statement - Korea Germany Compliance Statement Deutschsprachiger EU Hinweis: Hinweis für Geräte der Klasse B EU-Richtlinie zur Elektromagnetischen Verträglichkeit Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie 2004/108/EG zur Angleichung der Rechtsvorschriften über die elektromagnetische Verträglichkeit in den EU-Mitgliedsstaaten und hält die...
IBM-Allee 1, 71139 Ehningen, Germany Tel: +49 7032 15-2937 email: tjahn@de.ibm.com Generelle Informationen: Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse B. Terms and conditions Permissions for the use of these publications are granted subject to the following terms and conditions. Applicability: These terms and conditions are in addition to any terms of use for the the manufacturer website.
Page 46
PCI adapter placement for the 31E/2B, 31E/1C, or 31E/2C...
This manual is also suitable for:
Escala power7 e5-700Escala power7 m6-700Escala power7 m6-705Escala power7 m7-700Escala power7 m7-705Escala power7 e1-700...
Show all