Download Print this page

Viavi T-BERD MTS 5800 Quick Card

Network tester, ethernet layer 3 ipv4 traffic loopback
Hide thumbs Also See for T-BERD MTS 5800:

Advertisement

Quick Links

Quick Card
®
T-BERD
/MTS 5800 Network Tester
Ethernet Layer 3 IPv4 Traffic Loopback
This quick card describes how to set the T-BERD/MTS 5800 up as a Layer 3, IPv4 Loopback device.
Equipment Requirements:
• T-BERD/MTS 5800 equipped with the following:
o BERT software release V26.0 or greater
o Ethernet test options:
▪ C510M1GE for 10 Megabit to 1 Gigabit Ethernet
▪ C510GELAN for 10 Gigabit Ethernet
▪ C525GELAN for 25 Gigabit Ethernet
▪ C540GELAN for 40 Gigabit Ethernet
▪ C5100GELAN for 100 Gigabit Ethernet
o SFP, QSFP, or CFP4 optical transceiver to match the
line under test
• CAT5E cable or fiber optic Jumper cables to match the
optical transceiver and the line under test
• Fiber inspection microscope
(VIAVI P5000i or FiberChek Probe)
Fiber optic cleaning supplies
The following information is required to complete the test:
• Physical Interface (10/100/1000BASE-T, 1000BASE-LX, 10GBASE-LR, 100GBASE-LR4, etc.)
• Auto Negotiation settings of the port under test (if 1 Gigabit or below)
• Encapsulation (VLAN or None)
• VLAN ID (if Encapsulation = VLAN)
• Source IP Type (Static or DHCP)
• Source IP Address (if Source IP Type = Static)
• Subnet Mask (if Source IP Type = Static)
• Default Gateway (if Source IP Type = Static)
• Destination IP Address
Fiber Inspection Guidelines:
Inspect both sides of every fiber optic connection being used
(bulkhead connectors, patch cords, and SFP ports) prior to
reconnection for each test. Using the VIAVI P5000i or
FiberChek Probe microscope:
• Focus fiber on the screen. If dirty, clean the connector.
• If it appears clean, run inspection test.
• If it fails, clean the fiber and re-run inspection test. Repeat
until it passes.
VIAVI Solutions
Figure 1: Equipment Requirements
Figure 2: FiberChek Probe

Advertisement

loading

Summary of Contents for Viavi T-BERD MTS 5800

  • Page 1 Inspect both sides of every fiber optic connection being used (bulkhead connectors, patch cords, and SFP ports) prior to reconnection for each test. Using the VIAVI P5000i or FiberChek Probe microscope: • Focus fiber on the screen. If dirty, clean the connector.
  • Page 2 VIAVI Solutions • To inspect SFP ports with the P5000i, insert the probe tip into the SFP port, move the focus wheel all the way to one end, and slowly move the focus wheel to the other end. • To inspect SFP ports with the FiberChek Probe, manually focus with middle toggle switch or pull the trigger to auto- focus.
  • Page 3 VIAVI Solutions Launch and Configure Test: 1. Press the Power button to turn on the test set. 2. Using the Select Test menu, Quick Launch menu, or Job Manager, launch an Ethernet, Layer 3 Traffic, IPv4, Terminate test on port 1 for the desired physical interface.
  • Page 4 © 2018 VIAVI Solutions Inc. Contact Us +1 844 GO VIAVI To reach the VIAVI office nearest you, Product specifications and descriptions in this (+1 844 468 4284) visit viavisolutions.com/contacts. document are subject to change without notice.