Full Boar FBWC-15125 Instruction Manual
  1. Manuals
  2. Brands
  3. Full Boar Manuals
  4. Power Tool
  5. FBWC-15125
  6. Instruction manual

Full Boar FBWC-15125 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

KNOW YOUR PRODUCT
125MM
WALL CHASER
• 1500W MOTOR
• 5 - 29MM CUTTING DEPTH
• 8 - 30MM CUTTING WIDTH
INSTRUCTION MANUAL
WARNING: Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
0120

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FBWC-15125 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Full Boar FBWC-15125

Summary of Contents for Full Boar FBWC-15125

  • Page 1 KNOW YOUR PRODUCT 125MM WALL CHASER • 1500W MOTOR • 5 - 29MM CUTTING DEPTH • 8 - 30MM CUTTING WIDTH INSTRUCTION MANUAL WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.

  • Page 2: Specifications

    SPECIFICATIONS - MODEL NO. FBWC-15125 Power: 1500W Input: 230-240V ~ 50Hz No load speed: 8,500/min¯¹ Diamond disc: Ø125mm x Ø22.2mm Spindle: 14mm Cutting depths: 5 - 29mm Cutting widths: 8 - 30mm Sound power level: 110 dB(A) Gross weight: 7.26kg KNOW YOUR PRODUCT 125x2.0x7x22.23mm...

  • Page 3: Table Of Contents

    TABLE OF CONTENTS SPECIFICATIONS............Page 02 KNOW YOUR PRODUCT........... Page 02 INTRODUCTION............Page 04 SAFETY INSTRUCTIONS........... Page 04 SET-UP & PREPARATION........... Page 11 OPERATION............... Page 14 MAINTENANCE............Page 16 TROUBLESHOOTING..........Page 17 DESCRIPTION OF SYMBOLS........Page 18 CONTENTS..............Page 19 WARRANTY..............

  • Page 4: Introduction

    INTRODUCTION Congratulations on purchasing a Full Boar Wall Chaser. Your Full Boar Wall Chaser FBWC-15125 is ideal for cutting primarily mineral materials, such as reinforced concrete, masonry and road surfacing without the use of water. A flat chisel bit included within the kit box for user convenience and safe storage.
  • Page 5 GENERAL SAFETY INSTRUCTIONS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery operated (cordless) power tool.
  • Page 6 GENERAL SAFETY INSTRUCTIONS (cont). 4. Power tool use and care a. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b.
  • Page 7 WALL CHASER SAFETY WARNINGS WARNING! This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  • Page 8 WALL CHASER SAFETY WARNINGS (cont). f) Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and kickback. g) Use extra caution when making a “plunge cut” into existing walls or other blind areas. The protruding blade may cut objects that can cause kickback Safety instructions for plunge cut circular saws a) Check guard for proper closing before each use.
  • Page 9 WALL CHASER SAFETY WARNINGS (cont). d) Wheels must be used only for recommended applications. For example: do not grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter. e) Always use undamaged wheel flanges that are of correct diameter for your selected wheel.
  • Page 10 WALL CHASER SAFETY WARNINGS (cont). a) Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up. The operator can control torque reactions or kickback forces, if proper precautions are taken.

  • Page 11: Set-Up & Preparation

    SET-UP & PREPARATION WARNING! Ensure the tool is switched off and disconnected from the power supply before performing any of the following operations. Fitting the side handle (4) For safety reasons you must only use the wall chaser with the side handle (4) fitted. 1.
  • Page 12 SET-UP & PREPARATION (cont.) Fitting diamond discs (fig. 4-6) WARNING! When mounting and replacing diamond discs (10), it’s recommended to wear protective gloves. WARNING! Diamond discs (10) become very hot during operation; do not touch them until they have cooled down. 1.
  • Page 13 SET-UP & PREPARATION (cont.) 5. Press the spindle by pressing the spindle lock button (9), then tighten the flange nut (17) with the pin spanner (12) turning anti-clockwise. 6. Close the spindle cover and tighten spindle cover knob (3) 125x2.0x7x22.23mm Fig.

  • Page 14: Operation

    OPERATION WARNING! The power supply for this product should be protected by a residual current device (rated at 30mA or less). A residual current device reduces the risk of electric shock. WARNING! Before switching on, ensure that the diamond discs (10) do not touch the workpiece.
  • Page 15 OPERATION (cont.) Working advice WARNING! Clamp the workpiece if it does not remain stationary due to its own weight. • Place the wall chaser (with motor running) with the chaser roller (1) onto the surface the chase is to be cut into and slowly push down until the preset depth of cut is reached (fig.

  • Page 16: Maintenance

    MAINTENANCE • Keep the ventilation vents of the wall chaser clean at all times. • To prevent stone-dust build-up inside the wall chaser when used over extended periods, the motor needs to be cleaned periodically by blowing out with low pressure compressed air (through the vent slot at the rear end of the motor casing).

  • Page 17: Troubleshooting

    TROUBLESHOOTING Problem Cause Remedy Wall chaser is not No power supplied. Make sure the power plug is connected and power outlet is in working working order. Sparking visible A small amount of sparking This is normal and does not may be visible through the indicate a problem.

  • Page 18: Description Of Symbols

    DESCRIPTION OF SYMBOLS Volts Hertz Alternating current Watts Revolutions or No load speed reciprocation per minute Millimetres Diameter Double insulated Regulator compliance mark Wear ear, eye and breathing Warning protection Read instruction manual Decibel level CARING FOR THE ENVIRONMENT Power tools that are no longer usable should not be disposed of with household waste but in an environmentally friendly way.

  • Page 19: Contents

    CONTENTS 1 x Wall chaser 2 x Diamond cutting discs 1 x Side handle 1 x Flat chisel 1 x Pin wrench 1 x Set carbon brushes (spare) 1 x Kit box Note: The manufacturer’s liability shall be deemed void if the machine is modified in any way and the manufacturer shall therefore accept no liability for any damages arising as a result of modifications.

  • Page 20: Warranty

    WARRANTY YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE (see www.bunnings.com.au or www.bunnings.co.nz for store locations) WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR CUSTOMER SERVICE HELPLINE: Australia 1800 069 486 New Zealand 0508 069 486...

Table of Contents