Quick reference 1 Switching on/off with the ON button: Press ON. The unit will play at the preset volume. If the unit is switched off, a double beep tone will remind you that you should remove the detachable face before leaving your vehicle. Note: Read the information in the section on “Theft protection system”.
Page 5
Extra function AUD Loudness - When the system is played at a low volume level, the Loudness function creates a more natural sound by boosting the low frequency range. Loudness on/off: Press AUD for ap- proximately 1 sec. “LD” lights up in the display, if the Loudness function is switched on.
Page 6
5 Display d e f a) NDR1 NDS - Station name b) TR 1 - Track (side) 1 of the cas- sette c) 1:52 - Playback time and number (CD number and track) during changer op- eration (optional) d) FM - Waveband e) l, II, T - Memory bank I, II or...
Page 7
9 AF /TA TA (Traffic Announcement) If “TA” lights up in the display, the sys- tem will play traffic stations only. Priority on/off: Press AF/TA briefly. AF - Alternative frequency during RDS operation: If “AF” lights up in the display, the system will automatically seek a fre- quency offering better reception for the same RDS programme.
Page 8
Remote control (optional) - Audio mute You can instantly turn down the vol- ume by pressing briefly. “MUTE” will appear. The volume will be set to “VOL 0”. The function is cancelled by pressing or +. If - is pressed, the mute volume will be adopted.
Do not ground the loudspeaker outputs! Accessories Use only the accessories and spare parts approved by Blaupunkt. You can use the following Blaupunkt prod- ucts with this car radio: Changer CDC A 06 / A 072, CDC A 05 / F 05...
Release preset buttons 1 and 4. • Enter the code number given in the Blaupunkt car radio pass and confirm your entry as described in “Restart ...” Now the security coding system is active. The display will briefly show “CODE” each time the set is turned on.
Switching off security coding • Turn off the radio. • Press and hold down preset buttons 1 and 4 simultaneously, and • switch the set on. “CODE” will appear. • Release preset buttons 1 and 4. • Now enter the code number given in the car radio pass and confirm your entry (see example in “Re-start ...”).
Radio operation with RDS (Radio Data System) The Radio Data System offers you more convenience when you listen to FM radio stations. More and more radio stations have begun to broadcast RDS information along with their programmes. As soon as a programme has been identi- fied, the station name including a regional identifier, if applicable, will appear in the dis- play, for example, NDR1 NDS (regional pro-...
Station tuning Automatic tuning • Press / ; the car radio will automati- cally search for the next station. If you hold down the upper or lower part of the rocker switch, seek tuning will speed up in the upwards or downwards di- rection.
Note: Should you tune in a station which has al- ready been stored before, then the corre- sponding preset position and memory bank will briefly flash in the display. Automatically storing the strongest stations with Travel- store You can automatically store the five most powerful FM stations of your current recep- tion area sorted according to their signal strength.
Receiving traffic programme stations with RDS-EON The abbreviation “EON” stands for En- hanced Other Networks, meaning the ex- change of information within a radio network. Many FM broadcasters offer traffic messag- es for their service area at regular intervals. All traffic programme stations transmit a special carrier signal along with their pro- grammes, which is decoded by your car ra- dio.
Adjusting the volume for traffic announcements and the beep tone This volume was preset at the factory, though you can alter the value using the DSC function (see “DSC programming, TA VOL”). If the volume level is altered while a mes- sage is played, this will only affect the cur- rent announcement.
Reversing the tape To switch to the other side of the tape dur- ing playback, • press FR and FF simultaneously. At the end of the tape the unit will automat- ically reverse to the other side (autoreverse). The display shows “TR 1” for track (side) 1 or “TR 2”...
CD changer operation (optional) This piece of equipment offers you conven- ient control of a Blaupunkt CD changer CDC A 06 / A 072 or CDC A 05 / F 05 (with adapter 7 607 889 093). Note: Use only standard circular CDs measuring...
Selecting the display mode You can select the desired display mode for CD playback: NUMBER – The CD and track number, such as “CD08 T02” is dis- played. TIME – The elapsed playback time of the current title is dis- played, for example “2:32”.
DSC programming DSC (Direct Software Control) allows you to customise certain programmable, basic settings to suit your personal needs and preferences and then store them. The basic settings for this audio equipment were made at the factory. In the following you can find an overview of these settings, so that you can always reset to these if desired.
TA VOL To adjust the traffic an- nouncement and beep tone volume from between 0 to The message will then come through at this volume, if the volume set for the program is lower. If the program volume is higher than the TA VOL lev- el, the traffic report will be played slightly louder.
Address of the next service centre in your vicinity (only for Germany) If you would like to know the address of the next Blaupunkt service centre of your area without having our service list at hand: Find out your area code.