Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Linear BP-2001
Summary of Contents for Linear BP-2001
- Page 1 BP-2001 RPL 2000 1-Channel Beltpack Operating Instructions Page 1 of 11...
-
Page 2: Table Of Contents
1 General ..............3 2 Setting up ..............3 2.1 Front view ............3 2.2 Rear view ............4 2.3 Control elements and connectors ........4 2.4 Connecting the beltpack to a Riedel Party Line (RPL) ....5 3 Operation ..............5 3.1 Talk .............. -
Page 3: General
Apart from the call light, the beltpack also features an S-CALL button. With the BP-2001 you can now also talk to the radio users or switch paging system announcements directly from beltpack. Connection is established via a 3-pin XLR with loop-through, and a 4-pin XLR is used for the headset. -
Page 4: Rear View
2.2 Rear view 2.3 Control elements and connectors The BP-2001 is a single-channel beltpack and therefore has one talk key and a volume control. talk labelled “I”. The call light key is marked with the letter “L“ and also located at the front of the unit. -
Page 5: Connecting The Beltpack To A Riedel Party Line (Rpl)
(3-pin), as well as a 4-pin XLR for the headset. On the back of the unit are two sidetone trimmers, the BP-2001 only uses the upper one. 2.4 Connecting the beltpack to a Riedel Party Line (RPL) The beltpack is a portable headset station powered through the intercom wiring using the PS-2002 or PS-2004 power supply. -
Page 6: Receiving A Call Light Signal
On the back of the unit are two sidetone trimmers, one above the other. The top trimmer is responsible for setting the talk-back (sidetone) for Channel The trimmer underneath is not used with the BP-2001. You can adjust the talk-back from the user’s own microphone to the headset earpieces to suit the requirements of the user using the sidetone trimmer. -
Page 7: Programming
4 Programming 4.1 Programmable options If the intercom supply is applied, the BP-2001 can be programmed to special operating conditions in which the unit can be used. If the intercom power supply is switched off or the unit is unplugged, the programming remains in memory. -
Page 8: Programming Modes
4.2 Programming modes Proceed as follows to either check or set up modes: Switch off Talk function. Then simultaneously hold down the keys call light (L) and S-CALL (S). Next press the Talk key 5 times in succession. The buzzer sounds once. Service mode is now active. -
Page 9: Connecting Options
Audio channel B and +30 VDC Audio channel A Audio channel B is only used if the BP-2001 is assigned to RPL intercom channel B (II). This is not the default setting and must be configured using the beltpack´ s service mode if required. -
Page 10: Technical Data
6 Technical Data 6.1 Intercom Line 200 Ω Line Impedance: Line Level: -12 dBu up to +6dBu maximum Wire Type: 0,38 mm (AWG 22), 2 conductor shielded mic cable with <65pF/m capacity and <70Ω/km overall DC resistance Line Length (single channel): up to 5000m Signal to Noise, Single-Channel: -70dBu... -
Page 11: Power Consumption
6.4 Power Consumption BP-2001 beltpack 22 mA, avg., channels activated 7 Warranty This equipment is under warranty for 24 month from the date of delivery unless otherwise specified. All equipment found to have manufacturers defects or defects resulting from normal use within the warranty period will be repaired at no cost.
Need help?
Do you have a question about the BP-2001 and is the answer not in the manual?
Questions and answers