Download Print this page
Linear Technology DC2423A Demo Manual

Linear Technology DC2423A Demo Manual

High voltage isolated switch controller with i2c command and telemetry

Advertisement

Quick Links

Anyside™ High Voltage Isolated Switch Controller
DESCRIPTION
Demonstration circuit 2423A showcases the
Isolated Switch Controller in either a typical 48V applica-
tion (–A) or in a high voltage 380V application (–B). The
board may be configured for either high side or low side
operation, dependent on the connection of external sup-
ply and load to the banana jacks. An on board capacitive
load may also be wired into the circuit. LEDs indicate the
presence of input and output voltage. The MOSFET can be
PERFORMANCE SUMMARY
SYMBOL
PARAMETER
V
Input Supply Range
CC
I
Input Supply Current
CC
V
Logic Input Supply Range
L
UV Off Threshold
DC2423A-A 48V Input
DC2423A-B 380V Input
UV On Threshold
DC2423A-A 48V Input
DC2423A-B 380V Input
OV On Threshold
DC2423A-A 48V Input
DC2423A-B 380V Input
OV Off Threshold
DC2423A-A 48V Input
DC2423A-B 380V Input
Current Limit (Circuit Breaker) Threshold
DC2423A-A Trip Current
DC2423A-B Trip Current
Circuit Breaker GATE Off Delay
10-Bit ADC Full-Scale Voltage
Timer (TMR) Delay
Slow Start (SS) Time
V
Maximum Working Insulation Voltage
IORM
Common Mode Transient Immunity
Arrow.com.
Downloaded from
DEMO MANUAL DC2423A
2
with I
C Command and Telemetry
LTM
9100
easily exchanged or replaced due to screw terminal block
®
mounting. Protection is also included to protect the GATE
and SENSE pins in the event of MOSFET destruction. The
circuit can be operated manually or by computer control.
Design files for this circuit board are available at
http://www.linear.com/demo/DC2423A
L, LT, LTC, LTM, Linduino, Linear Technology and the Linear logo are registered trademarks
and QuickEval and Anyside are trademarks of Linear Technology Corporation. All other
trademarks are the property of their respective owners.
Specifications are at T
= 25°C
A
CONDITIONS
V
Rising
UV
V
Falling
UV
V
Rising
OV
V
Falling
OV
R
= 0.008Ω ±1%
S
R
= 0.017Ω ±1%
S
SENSE > 50mV
SENSE
ADIN, ADIN2
GND to V
EE
LTM9100
MIN
TYP
MAX
UNITS
4.5
5
5.5
50
3
3.3
5.5
2.518
2.56
2.598
41.8
43.4
44.9
251
261
270
2.248
2.291
2.328
37.3
38.8
40.3
224
233
242
1.735
1.770
1.805
69.8
71.8
73.9
420
432
444
1.673
1.733
1.787
67.3
70.3
73.1
405
423
440
45
50
55
5.57
6.25
6.94
2.62
2.94
3.27
440
530
620
62.8
64
65.2
2.514
2.56
2.606
12
56
1000
690
VRMS
30
50
dc2423af
V
mA
V
V
V
V
V
V
V
V
V
V
V
V
V
mV
A
A
μs
mV
V
ms
ms
VDC
kV/µs
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the DC2423A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Linear Technology DC2423A

  • Page 1 LEDs indicate the L, LT, LTC, LTM, Linduino, Linear Technology and the Linear logo are registered trademarks presence of input and output voltage. The MOSFET can be and QuickEval and Anyside are trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners.
  • Page 2: Operating Principles

    DC590 Arduino code). Example Arduino JP1: EEPROM Program (PG) or Write Protect (WP). For code specifically for the DC2423A is also available for the factory use only in programming the demo board ID for DC2026. The LTM9100 includes an I C/SMBus interface QuickEval.
  • Page 3 Broadcast Mode. To do this, set the I C address jumpers between DC2423A and a PC, complete with isolation. to ADR0 = LO and ADR1 = HI. A serial data stream is then Simply plug in the 14-wide interface cable from J5 to the observable on the SDA pin of J5 or SDA test point near DC590 or DC2026.
  • Page 4: Quick Start Procedure

    LTM9100. For the proper setup of 6. The LTM9100 can be turned on by moving the EN jumper a high side 48V application using the DC2423A-A, refer to (JP4) to the ON position, or by connecting external Figure 1 and follow the procedure below.
  • Page 5 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa- tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
  • Page 6 Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions: This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety measures typically found in finished commercial goods.

This manual is also suitable for:

Anyside ltm9100