Advertisement
**** PLEASE READ THOROUGHLY PRIOR TO USE FOR IMPORTANT SAFETY INFORMATION****
WARNING:
Sections labeled "Warning" can lead to serious injury or death if not followed. Please thoroughly read these sections and understand them completely
before use. If you do not understand them or have any questions, contact your retailer or Blichmann Engineering (www.BlichmannEngineering.com)
before use.
CAUTION:
Sections labeled "Caution" can lead to equipment damage or unsatisfactory performance of the equipment. Please read these sections thoroughly. If
you have any questions, contact your retailer or Blichmann Engineering (www.BlichmannEngineering.com) before use.
IMPORTANT:
Sections labeled "Important" should specifically be followed to ensure satisfactory results with the product.
WARNING
1.
Never operate this product unattended.
2.
Never move this product during use.
3.
ALWAYS install this product on a level solid surface such as concrete.
4.
Heated liquids remain at scalding temperatures long after the brewing process. Never touch the Foundry™ until the liquids have cooled to 115°F (45°C) or
less. The use of heat protective gloves is recommended.
5.
Ensure the voltage selector is correct.
6.
Use with GFCI protected circuit ONLY.
7.
Do not immerse the Foundry™ Boiler in liquid.
8.
Do not boil with the lid installed.
9.
Operating the Foundry™ in any fashion other than described in this manual can result in personal property damage, injury, electrocution, death, or loss of
seriously good beer.
GENERAL PRECAUTIONS
1.
Do NOT leave this product unattended while in use. The user must remain in the immediate area of the product and have a clear view of the product at all
times during operation.
2.
Keep children and pets away from the Foundry™ at all times.
3.
The use of alcohol, prescriptions or non-prescription drugs may impair your ability to properly assembly or safely operate this product.
4.
Use ONLY on-a level, stable surface.
5.
Avoid bumping or impact with the product to prevent spillage or splashing of hot liquid.
6.
This product will be hot during use.
7.
In case there is a fire, call the local fire department. Stay clear from flames.
8.
This product is not intended or warranted for commercial use.
9.
Make sure the Foundry™ is disconnected from all power sources before cleaning.
What's Included
Item
Boiler
Malt Basket
Dip Tube
Valve Assembly
Teflon Washer
Basket Support Ring
Lid
Knob Washer
Screw for Lid
Knob
Immersion Chiller
Hose for Chiller
1/2" Hose Clamps
Hose Barb
*120V Standard
Anvil Brewing Foundry™ - V4
©Anvil Brewing Equipment 2019 | www.anvilbrewing.com
Foundry™
Assembly & Maintenance Manual
Quantity
1
1
1
1
1
1
1
2
1
1
1
10 Feet
3
1
Optional Accessory
Recirculation Kit
1
What's Included
Item
Quantity
Anvil Pump
Silicone Hose
4 Feet
Hose Clamp
Flow Clamp
Stainless Return Tube
Perforated Disc
Eye Bolt
Nuts for Eye Bolt
1
4
1
1
1
1
2
Advertisement
Table of Contents
Summary of Contents for Anvil Foundry
- Page 1 ALWAYS install this product on a level solid surface such as concrete. Heated liquids remain at scalding temperatures long after the brewing process. Never touch the Foundry™ until the liquids have cooled to 115°F (45°C) or less. The use of heat protective gloves is recommended.
- Page 2 Basket Support Ring Assembly Place the basket support ring into the top of the Foundry™. The basket support ring will fit firmly into the top. If the ring does not fit firmly, stretch out the ring until it fits snugly. This will prevent the ring from popping out accidentally.
- Page 3 Warning: Ensure the Foundry™ is unplugged from any power source before wiring. To operate the Foundry™ on 240V, cut off the 120V plug and strip the sleeve from the wires about one inch away from the end. Strip each wire ½” away from the ends. Your plug may require different lengths. Tighten the terminal screws per the instructions included with the plug.
-
Page 4: Operation
Note: Make sure you have enough clearance above the Foundry™ to lift the grain basket. The pump must be at the same level as the base of the Foundry™ as shown to work properly. The flow clamp is not intended to completely stop the flow. To stop flow, turn off the pump. - Page 5 Most mashes are one hour in length, but follow your recipe if it recommends a different time. At the end of the mash, ensure the basket support ring is secure on the upper lip of the Foundry™. Carefully raise the mash basket to the ring and let it set to drain.
-
Page 6: Water Chemistry
Stir well to ensure the ingredients completely dissolve. There may be some cloudi- ness initially; this is acceptable. We recommend the Anvil Precision Scale for making these measurements. Anvil Brewing Foundry™ - V4... -
Page 7: Operating The Temperature Controller
To set the delay timer for the Foundry™, first fill the unit with water to the desired level. Set the temperature and power of the Foundry™. Press and hold the %PWR for 3 seconds and 1h will appear. Release the buttons and use the + to increase the time delay by 1 hour increments. -
Page 8: Cleaning And Maintenance
10-15 minutes of the boil. Turn the Foundry™ off and run cold tap water through the coil until wort has reached the pitching temperature. Stirring with a sanitized spoon will speed the cooling process significantly. -
Page 9: Recommended Accessories
O2 Wand with Regulator Distillation Ready The Foundry™ integrates seamlessly with the Turbo 500 Still unit. For installation, remove the knob and knob washers on the lid. Follow all operation instructions in the Turbo 500 Still manual. Zero to 100% power and temperature control makes the Foundry™ ideal for distillation. Install the stopper (BE-000689-00) in the lid hole when in use, which is included if you purchased the distillation kit through ANVIL Brewing Equipment. -
Page 10: Troubleshooting
If the Foundry™ does not turn on when powered up, see Power Source Overview for more information. If the unit is accidentally ran without water the dry run switch will cut the power to the heaters. An error code “E3” will appear to reset: 1. - Page 11 3. This warranty does not cover, and in no event shall ANVIL Brewing Equipment be liable for, travel, lodging, or any other expense incurred due to manufacturing defects in material and work manship, or any other reason.