Placement; Connection - Toshiba TLP TLP-X2000 Owner's Manual

Placement

Placement Styles
As shown in the figures below, this device can be placed in 4 different styles.
The factory setting is "floor-mounted front projection." Set the [Projection mode] in the
Default setting 2 menu, in accordance with your needs.
Floor-mounted front projection
Ceiling-mounted front projection
WARNING
• Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.
Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus
resulting in injury.
• If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the
projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge.
Improper mounting could cause the projector to fall, resulting in an accident.
• If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let
everyone involved with the use of the projector know that fact.
Projection Distance and Size
Use the figures, tables, and formulas below to determine the projection size and projection
distance. (Projection sizes are approximate values for full-size picture with no keystone
adjustment.)
As seen from above
Screen
90°
As seen from the side
Lens center
90°
H
a
a is the distance (m) between the lens and the screen,
and corresponds to a range of 1.19 m to 9.13 m. H is the
height from the image bottom to the center of the lens.
p.43
Floor-mounted rear projection
Ceiling-mounted rear projection
projection size (inches) – 0.8786
a (min length) =
32.773
projection size (inches) – 0.7244
a (max length) =
27.248
projection distance a (m)
projection height (H)
min length max length
size (cm)
(zooming max) (zooming min)
33 (84) – 1.19
40 (102) 1.19 1.44
60 (152) 1.80 2.18
80 (203) 2.41 2.91
100 (254) 3.02 3.64
150 (381) 4.55 5.48
200 (508) 6.08 7.31
250 (635) 7.60 9.15
300 (762) 9.13 –
22

Connection

Before connection
• Read the owner's manual of the device you are connecting to the projector.
• Some types of computer cannot be used or connected to this projector.
Check for an RGB output terminal, supported signal
• Turn off the power of both devices before connecting.
• The figure is a sample connection. This does not mean that all of these devices can or
must be connected simultaneously. (Dotted lines mean items can be exchanged.)
Computer
(for control)
To audio output
White (L)/Red (R)
To
RS-232C
p.59
terminal
Control cable
AV cable
(not supplied)
To audio
output
To video
White (L)/
output
Red (R)
Video recorder, etc.
(cm)
6.0
7.3
10.9
14.5
18.1
27.2
36.3
45.4
54.4
p.57 , etc.
Video recorder, Computer
DVD player, etc.
To S-video output
Audio cable
S-video cable
(not supplied)
(not supplied)
To audio output
Audio cable
(not supplied)
Audio cable
(not supplied)
Audio cable
(not supplied)
To audio input
To audio
White (L)/Red (R)
output
Audio amplifier, etc. DVD video recorder, etc.
23
Computer
To RGB
To audio
output
output
To RGB
Audio cable
output
(not supplied)
RGB cable
RGB cable
(not supplied)
(supplied)
Monitor
It is necessary to
switch to MONITOR
OUT by the switch.
p.18
Monitor cable Mini
D-sub 15P-BNC
(not supplied)
To Y/C /C output
B R
Green (Y)/Blue
(C B )/Red (C R )
Conversion
adapter BNC-pin
(not supplied)