Bust-a-Move Frenzy ™ Safety Operation Before operating game, read this manual. Failure to properly install and operate this game could result in malfunction or accident. Operate the game in accordance with the manual. Transporting The cabinet is very heavy. Because the monitor is high, the cabinet is also very top-heavy. Use appropriate care when moving or transporting cabinet.
Keep this manual available and ready for use. If the game fails to function properly, turn off the machine and unplug the AC line cord. Contact your local distributor. You may not reproduce this document or any of its contents without written authorization from Raw Thrills, Inc. Specifications For reasons such as performance, this product’s specifications may change without notice.
Bust-a-Move Frenzy ™ Product Specifications Electrical Power United States, International and Japan Operating AC Current: 5/2.5 Amps Voltage: 115/230~ VAC 50/60Hz Inrush AC Current: 5 Amps Temperature Humidity 50° F to 104° F Must not exceed 95% relative humidity (10° C to 40° C)
Bust-a-Move Frenzy ™ Fuse Replacement Guide NOTE: FOR CONTINUED PROTECTION AGAINST FIRE AND ELECTRICAL DAMAGE, USE ONLY SPECIFIED FUSE TYPE AND VALUE. 12V Power Distribution Please see unit for specified fuse labeling. Cabinet: 6x 5A 250V 3AG Slo-Blo Fuse (Littelfuse 0313005)
Bust-a-Move Frenzy ™ Setup Unpack Materials 1. Place the shipping crate(s) on a flat, stable surface. 2. Cut the banding straps and remove the cardboard lids. 3. Lift off the large cardboard containers surrounding the cabinet assembly and remove any shipping cleats.
Bust-a-Move Frenzy ™ Listed below is a step by step process to assemble the LED Display for Bust-a-Move Frenzy™. For additional assistance, reference the full Assembly and Service Procedure included with the game. 2 people are required to do the assembly. Ladders are recommended when assembling the top quadrants of the LED screen.
Bust-a-Move Frenzy ™ Cabinet Assembly 1. Using above diagram as a guide install lower sign using Phillips bit with supplied (4) M5 X 12mm screws. To secure cinch brackets to tubes, be sure to remove protective backing from double sided foam tape.
Page 17
Bust-a-Move Frenzy ™ 7. Connect the provided network cable between the back of the completed cabinet at the terminal near the on/off switch and the back of the LED wall assembly. Use supplied D-channel sleeve and carpet tape to properly dress the network cable on the floor.
Bust-a-Move Frenzy ™ Card Reader Installation and Setup Due to the rising popularity of aftermarket debit card systems for cashless or coinless operation of amusement machines (i.e. Embed, Intercard, Semnox), this NERF™ Arcade cabinet is equipped with UCL compatible harnessing to ensure that the installation process is easier and less prone to miswiring.
Bust-a-Move Frenzy ™ Check Electrical Settings 1. Verify the voltage in the nearest AC outlet. 2. Verify the AC outlet ground connection is present and working. Startup Game 1. Plug the line cord into an AC outlet. 2. Turn the main cabinet power switch on.
Bust-a-Move Frenzy ™ Diagnostic and Adjustments The Service Button Panel has four buttons, three of which can navigate the menu system. The control panel buttons and joysticks/guns can also advance through test menu screens. Navigating the Test Menu Button Action...
Bust-a-Move Frenzy ™ Basic Functional Test on Initial Power Up 1. Enter the Input Test and verify all switch inputs are working. 2. Enter the Sound Test and verify the audio works and is not distorted. 3. Enter the Light Test and verify that all the lights are working properly.
Bust-a-Move Frenzy ™ Test Menus Main Menu Choose from all available operator settings and menus here. You can use the test menu bracket and volume buttons to navigate. The guns/gun triggers are also available to use for easier navigation through these menus.
Bust-a-Move Frenzy ™ Diagnostics Verify or diagnose the operations of all game functions. DIAGNOSTICS INPUT TEST GUN SOLENOID TEST AUDIO TEST CABINET LIGHTS TEST METER TEST TICKET TEST WATCHDOG TEST EXIT • Input Test: Test input hardware such as switches.
Bust-a-Move Frenzy ™ Pricing and Payout Adjustments (Cash) Set pricing and payout adjustments for game operation. PRICING AND PAYOUT ADJUSTMENTS (CASH) CURRENCY INPUT CURRENCY TYPE COIN VALUE COINS TO PLAY PAYOUT PERCENT TICKET VALUE JACKPOT FIXED TICKETS FREE PLAY MERCY TICKETS...
Bust-a-Move Frenzy ™ Pricing and Payout Adjustments (Tokens) Set pricing and payout adjustments for game operation. PRICING AND PAYOUT ADJUSTMENTS (TOKENS) CURRENCY INPUT CURRENCY TYPE TOKEN VALUE TOKENS TO PLAY PAYOUT PERCENT TICKET VALUE JACKPOT FIXED TICKETS FREE PLAY MERCY TICKETS...
Bust-a-Move Frenzy ™ Pricing and Payout Adjustments (Swipes) Set pricing and payout adjustments for game operation. PRICING AND PAYOUT ADJUSTMENTS (SWIPES) CURRENCY INPUT CURRENCY TYPE SWIPE VALUE (IMPORTANT SETTINGS) NUMBER OF CARD READERS PAYOUT PERCENT TICKET VALUE JACKPOT FIXED TICKETS...
Bust-a-Move Frenzy ™ Game Settings Adjust game settings for operation. GAME SETTINGS ATTRACT MUSIC FREQUENCY EXIT • Attract Music Frequency: Set how often music should be played in attract mode. (Attract mode is a pre-recorded demonstration of the gameplay that is displayed when the game is not being played.
Bust-a-Move Frenzy ™ System Settings Adjust system settings for operation. SYSTEM SETTINGS SCREEN BRIGHTNESS CABINET LED BRIGHTNESS TRADESHOW MODE DATE + TIME LANGUAGE EXIT • Screen Brightness: Adjust the brightness of the screen. • Cabinet LED Brightness: Adjust the brightness of the cabinet lighting.
Bust-a-Move Frenzy ™ Audits View machine statistics such as games played, money, earned, etc. AUDITS SYSTEM AUDITS COIN AUDITS GAME AUDITS EXIT • System Audits: View system audits. • Coin Audits: View coin audits. • Game Audits: View game audits.
Bust-a-Move Frenzy ™ Resets Menu Reset various machine settings and audits. RESETS MENU RESET CREDITS RESET PLAYER 1 TICKETS RESET PLAYER 2 TICKETS RESET PRICING ADJUSTMENTS RESET GAME AUDITS RESET SYSTEM AUDITS RESET COIN AUDITS RESET ALL AUDITS FACTORY RESTORE EXIT •...
Bust-a-Move Frenzy ™ Volume Adjust all volume settings. VOLUME GAME VOLUME ATTRACT VOLUME CREDIT VOLUME MINIMUM VOLUME EXIT • Game Volume: Adjust the volume during gameplay. • Attract Volume: Adjust the volume during the attract mode sequences. • Credit Volume: Adjust the volume of the credit chime.
CALIBRATION GUN CALIBRATION EXIT • Gun Calibration: Follow on screen prompts to calibrate guns. NOTE: Bust-a-Move Frenzy™ only uses the “X” axis potentiometer L/R movement for calibration. 32 | P a g e...
Bust-a-Move Frenzy ™ Advertising Advertising feature that allows the operator to upload images which will be displayed during the attract mode of the game. Desired resolution: 224px x 288px. Formats: TGA, PNG, JPG, JPEG, and GIF ADVERTISING AD SLOT 1...
Bust-a-Move Frenzy ™ System Information View hardware and software information. • Serial Number • Software REV • Build Date • RIO PCB • RIO Firmware • Dongle Version • Cabinet Type • Game Template 35 | P a g e...
Bust-a-Move Frenzy ™ Choosing the Right Pricing Adjustments for Your Location Card Swipe Locations • Make Sure Your Game is Set to Swipes Mode: 1. Hold the Test Button for 2 seconds to enter the Test Menu. 2. Select “Pricing Adjustments” from the menu.
2) After you have your images picked out, sized and copied to your USB flash drive, you are now ready to upload the images into Bust-a-Move Frenzy™. Open the coin door and find the service bracket that has the test menu and service buttons. On this bracket, you will find a USB slot to insert your flash drive.
Page 38
Bust-a-Move Frenzy ™ 3) Once your USB flash drive is inserted into the USB slot on the service control panel, you can then press the “TEST” button to access the main menu. 4) Select “ADVERTISING” from the main menu to access the upload feature. From this menu you then select an ad slot for your image.
Bust-a-Move Frenzy ™ PC Hardware Your Bust-a-Move Frenzy™ game uses a Fujitsu IMP-3313-S4-4G-HD Mini PC computer ("Fujitsu Mini PC"). OTICE WARNING: DO NOT ENTER THE BIOS SETTINGS MENU! Modifying the BIOS settings will cause your game to stop functioning. In order to boot, new security features verify the BIOS settings against factory settings, including timestamp.
Bust-a-Move Frenzy ™ Fujitsu Mini BIOS To Access BIOS Settings: With the computer powered off, plug a USB keyboard into an open USB slot. Hold the ‘F2’ key and turn the computer on. Continue holding the F2 key until the BIOS Setup screen appears.
4. Turn cabinet power switch to OFF. Wait 30 seconds. 5. Turn cabinet power switch to ON. 6. Select the Bust-a-Move Frenzy™ restore version from the menu and follow on screen instructions 7. If recovery does not begin, check to ensure USB Drive is inserted correctly and is not damaged.
Bust-a-Move Frenzy ™ Troubleshooting Warning: Review the Safety section before making any adjustments to the game. Problem Possible Cause Solution Game not plugged in. Plug game into AC outlet. Game not turned on. Turn on main power switch. Check and replace fuse. See Game fuse is blown.
Page 43
Bust-a-Move Frenzy ™ Problem Possible Cause Solution To test a USB port, turn off the game, disconnect the device from the port, and then connect the game dongle to the port. PCB connected to faulty USB Neither buttons nor audio Reboot the game.
Page 44
Bust-a-Move Frenzy ™ Problem Possible Cause Solution Check external DC supply and Faulty power supply. the PC supply. Constant low audio hum. Check all ground wires in Open ground. cabinet. Ensure AC wall outlet is properly grounded Game does not load.
Page 45
Bust-a-Move Frenzy ™ Problem Possible Cause Solution Check wiring from meter to PCB No pulse to meter. board. Coin meter does not click Faulty meter. Replace coin meter. during test. Blown fuse(s) on PCB Replace 12vdc 5A fuse(s) on PCB.
Page 46
Bust-a-Move Frenzy ™ Problem Possible Cause Solution Check ribbon cable between malfunctioning module and module to the left (from the back). Check/replace module to the left (from the back). Faulty data transmission. If module is left-most in quadrant Entire row or column of (from the back): defective pixels.
Page 47
Bust-a-Move Frenzy ™ Screen Note 1: Bust-a-Move Frenzy™ uses over 65,000 LEDs on its giant screen. It is normal for a few LEDs to fail over the course of operating the game. This will not affect normal operation or viewing of the game and most will not be noticeable to the eye.
Page 48
Bust-a-Move Frenzy ™ Advertising Image Troubleshooting Error Solution Check your USB drive to ensure it is properly connected. Also, check to make sure your USB drive can be read on USB device not connected. other devices. Ensure the coin door USB connection able to the PC inside the cabinet did not become disconnected or dislodged.
Page 49
Q: Does this game come with a Ticket Dispenser? A: Bust-a-Move Frenzy™ does come equipped with ticket dispensers. Q: Can I advertise on the screen? A: You can advertise on the screen. Ad files can be loaded via the test menu and should be 224px x288px (acceptable formats: TGA, PNG, JPG, JPEG, and GIF).
Bust-a-Move Frenzy ™ Technical Support For an authorized distributor near you, check the Raw Thrills website at www.rawthrills.com Betson’s Raw Thrills Technical Support Hotline Phone: 1-800-753-2513 FAX: 1-201-438-5019 Email: rtsupport@betson.com Assembly and service videos: rawthrills.com/assembly-and-service-videos/ 50 | P a g e...
Bust-a-Move Frenzy ™ Electrical and Mechanical Illustrations 51 | P a g e...
Page 52
Install network cable for LED wall display into cord protector and secure with supplied carpet tape. Channel may be cut to shorter length as needed. Additional or alternative tape may be needed to properly secure to floor, depending on location. Bust-A-Move Frenzy Game Assembly...
Page 53
>> PART NUMBERS ON NEXT PAGE > CABINET DECALS >> 606-01826-01 - MAIN CABINET RIGHT DECAL >> 606-01827-01 - MAIN CABINET LEFT DECAL >> 606-01832-01 - CONTROL PANEL DECAL >> 606-01833-01 - REAR CONTROL PANEL DECAL Bust-A-Move Frenzy Control Cabinet Assembly (BOM on next page)
Page 54
> 606-01817-01 - P2 Gun Lower Left Decal > 606-01818-01 - P2 Gun Small Lower Left Decal > 606-01819-01 - P2 Gun Upper Right Decal Bust-A-Move Frenzy > 606-01820-01 - P2 Gun Lower Right Decal > 606-01821-01 - P2 Gun Small Lower Right Decal Control Cabinet Assembly >...
Page 55
1/4" Long AEH - 04-12-750 Wire Harness Clip (for 3/4" Bundle Diameter) McMaster-Carr - Steel Locknut with External-Tooth Lock Washer, 90675A009 Zinc-Plated, 8-32 Thread Size, 11/32" Wide Bust-A-Move Frenzy RIO Assembly w/ Mounting Plate ITEM NO. PART NUMBER DESCRIPTION QTY. 600-01754-01...
Page 56
McMaster-Carr - 90631A009 Locknut, Zinc-Plated, 8-32 Thread Size 600-00043-01 Lock Retainer Plate Flanged Hex Head Screws for McMaster-Carr - 90054A196 Sheet Metal, Zinc-Plated Steel, Number 8 Size, 5/8" Long Standard Door Lock Assembly 150-00001-00 (for 3/4" Panels) Bust-A-Move Frenzy Back Door Assembly...
Page 57
Sheet Metal, 18-8 Stainless Steel, Number 8 Size, 95638A197 3/4" Long 603-01002-01 12" Clear T-Molding Clip Tamper-Resistant Torx Rounded Head Screws for Partec - 31-TP008-03-003 Sheet Metal, Black Oxide Steel, Number 8 Size, 3/4" Long Bust-A-Move Frenzy Pedestal Cabinet Assembly...
Page 58
Bust-A- Rear Seat LED Assembly Move_Rear_Seat_LED_Assy Flanged Hex Head Screws for Sheet McMaster-Carr - 90054A194 Metal, Zinc-Plated Steel, Number 8 Size, 1/2" Long Bust-A-Move Frenzy Rear Seat LED Cap Assembly ITEM NO. PART NUMBER DESCRIPTION QTY. 603-00806-01 LED Cap Back...
Page 59
Washer for Number 10 Screw Size, 0.17" 90133A013 ID, 0.375" OD P1 Seat Marquee - GREEN "Bub" 606-01823-01 P1 Seat Marquee PETG P2 Seat Marquee - BLUE "Bob" 606-01824-01 P2 Seat Marquee PETG Bust-A-Move Frenzy Seat Assembly (unique seat marquee for P1 & P2)
Page 60
"LED Display Quick Set-up Guide" earlier in this manual as well as separate manual "P7.62 LED Wall Assembly and Service Document" that was included with this game. Both of these manuals can also be found on Raw Thrills' website: www.rawthrills.com Bust-A-Move Frenzy...
Page 61
CABLE CLAMP 18 600-01567-01 SMALL POT GEAR 19 HAPP 50-2670-01 POT - 5K LOWER MECH ASSEMBLY TOP ASSEMBLY RAW THRILLS INC. TITLE: GUN MAIN ASSEMBLY NOTES: 1) ALL SCREWS SHOULD BE INSTALLED WITH BLUE LOCTITE 242 or 243. TOL: .X ±.030 MATERIAL: .XX ±.015...
Page 62
6-32 HEX LOCKNUT - BLACK 6-32 X 2.5" PHILLIPS HEAD SCREW - 28 999-00017-01 BLACK 29 600-01419-01 PINCH COVER LOWER MECH ASSEMBLY RAW THRILLS INC. TITLE: GUN MAIN ASSEMBLY NOTES: TOL: .X ±.030 MATERIAL: 1) ALL SCREWS SHOULD BE INSTALLED WITH BLUE LOCTITE 242 or 243.
Page 63
HAPP #95-0637-00 COIL SLEEVE MMC 93298A109 10-32 FLANGED LOCKNUT PEEL AND STICK DAMPER PAD WITH CENTER HOLE CONCENTRIC TO COIL BRACKET SHAKER ASSEMBLY RAW THRILLS INC. TITLE: GUN MAIN ASSEMBLY TOL: .X ±.030 MATERIAL: NOTES: .XX ±.015 1) SET SCREW AND LOCKNUTS SHOULD BE INSTALLED WITH RED LOCTITE 262.
Page 64
GRIP, RIGHT HALF 608-00218-01 96-0110-00 TRIGGER BUMPER SCREW, #8-32 x 1 TP MMC 96075A147 43-0378-00 BLACK MMC 86537A140 43-1124-00 HEX NUT #8-32 BLACK GRIP ASSEMBLY RAW THRILLS INC. TITLE: GRIP ASSEMBLY TOL: .X ±.030 MATERIAL: .XX ±.015 .XXX ±.005 FINISH: SEE NOTES HOLES: +.002/-.000...
Page 65
SCALE 1 : 1 1) ALIGN FLAT ON POT DOWNWARD AND POINTING TOWARD CENTER OF SEGMENT GEAR UP AND DOWN LEFT TO RIGHT POT ALIGNMENT POT ALIGNMENT RAW THRILLS INC. TITLE: POT ALIGNMENT DRAWING TOL: .X ±.030 MATERIAL: SEE NOTES .XX ±.015 .XXX ±.005...
Page 66
1) APPLY LOCTITE RED 271 TO HEX BOLT (ITEM 12) THREADS TO SECURE BUBBLE BALL (ITEM 1) TOL: .X ±.030 MATERIAL: 2) APPLY A RAW THRILLS APPROVED ADHESIVE TO THE END OF PIN (ITEM 11) AND INSERT IT INTO SMALL BLACK GUN DISC (ITEM #5) SEE NOTES .XX ±.015 .XXX ±.005...
Page 67
IG GND IG GND DISPLAY CABINET CODLING FAN 2 RE n--1--� � � _Y� =------ "-+ -----'- =------ ----1. 24 V IG GND IG GND \JER BUST-A-MOVE FRENZY • FD CONTINU □ CIFI D FU L Y S TING. (1/1)
Need help?
Do you have a question about the Bust-a-Move Frenzy and is the answer not in the manual?
Questions and answers