Table of Contents
Advertisement
Quick Links
™
™
®
®
DESIGNED FOR THE ART OF WINNING
™
DYE Precision, Inc. 10637 Scripps Summit Ct. San Diego, CA 92131
www.dyepaintball.com
P 858-536-5183 F 858-536-5191
©2003 DYE Precision, Inc. The stylized "dye" logo, the "Sphere" logo and the "DM4" logo
are either registered trademarks, trademarks, design trademarks, patents or pending patents of DYE Precision, Inc.
Covered by one or more of the following U.S. Patents 5,613,483: 5,881,707: 5,967,133: 6,035,843 and 6,474,326.
Advertisement
Table of Contents
Related Manuals for dye DM4
Summary of Contents for dye DM4
- Page 1 P 858-536-5183 F 858-536-5191 ©2003 DYE Precision, Inc. The stylized “dye” logo, the “Sphere” logo and the “DM4” logo are either registered trademarks, trademarks, design trademarks, patents or pending patents of DYE Precision, Inc. Covered by one or more of the following U.S. Patents 5,613,483: 5,881,707: 5,967,133: 6,035,843 and 6,474,326.
-
Page 2: Table Of Contents
< < S P E C S > > W E I G H T [ 2 . 3 L B S ] W I D T H [ 1 . 3 7 5 ” ] L E N G T H [ 9 . -
Page 3: Quick Reference
Turning the adjustment screw counterclockwise, or out, will raise the output pressure, increasing the velocity. NOTE: If the battery is too low, it may not be able to power the solenoid correctly. This will affect your DM4’s velocity, causing it... - Page 4 When ABS is activated, the dwell is increased after 15 seconds of non-use for the next shot fired. As soon as the marker is turned on and the LED turns from blue to either red or green, the DM4 is ready to fire. If there is no This helps to prevent bolt-stick, but may result in higher velocity for the first shot.
- Page 5 Trigger sensitivity is the amount of time that the trigger has to be released before next trigger pull is allowed. There is no low battery warning on the DM4. The 9V battery will last for about 40,000 shots, but there are big In some situations with too low of a value, the marker may begin to shoot full-auto.
-
Page 6: Fuse Bolt
The FUSE Bolt has four components If you do not grease the bolt, you will run the risk of damaging o-rings. This will create excessive friction and drag on the bolt, ultimately resulting in breaking the bolt. When greasing the DM4 bolt Cylinder kit, pay special attention to all o-rings that are on the bolt and that ride on a surface of the bolt. -
Page 7: On/Off Valve
This pressure is used to move the bolt forward and back. The factory setting is 75 PSI. You can fine tune your DM4 to its minimum cycle pressure. This will reduce the amount of force of the bolt hitting the ball (reducing ball breaks) and help with efficiency. -
Page 8: Hyper
Swivel Shims Seat housing Piston To remove the eye covers you will need a 1/16” Allen wrench [.050” Allen for the first runoff DM4’s]. Simply insert the Allen wrench into Seat Reg cap W A R N I N G... -
Page 9: Trigger Adjustment
L I S T The trigger’s forward travel and over travel are fully adjustable so that the user can fine-tune the trigger to his or her exact liking. • Remove the grip frame from the body of the DM4. Adjustable Feed Neck •... -
Page 10: Trouble Shooting Guide
DM4. repair or replacement of defective parts with the customer to pay shipping costs. Warranty card and proof of purchase must be submitted to Dye Precision for Remove the LPR and change the back-most #15 o-ring on the LPR body. If that does not help, change the seal retainer inside the LPR body.