Samsung S630 Service Manual
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Digital Camera
  5. S630 - Digital Camera - Compact
  6. Service manual

Samsung S630 Service Manual

Hide thumbs Also See for S630:

Advertisement

Table of Contents

Advertisement

Table of Contents
loading

Related Manuals for Samsung S630

Summary of Contents for Samsung S630

  • Page 2: Table Of Contents

    C O N T E N T S Ⅰ Ⅰ . SPECIFICATION 1. CAMERA SPECIFICATION …………………………………………………………………………………… 4 2. SYSTEM REQUIREMENTS …………………………………………………………………………………… 7 3. LCD monitor indicator …………………………………………………………………………………………… 8 4. CONNECTION DIAGRAM …………………………………………………………………………………… 11 5. IDENTIFICATION OF FEATURES …………………………………………………………………………… 12 Ⅱ Ⅱ . . E E X X P P L L O O D D E E D D V V I I E E W W A A N N D D P P A A R R T T S S L L I I S S T T 1.
  • Page 3 Ⅴ Ⅴ . . C C I I R R C C U U I I T T D D I I A A G G R R A A M M …………………………………………………………………………………………………… 85 1) MAIN_S3-63 ……………………………………………………………………………………………… 86 2) MAIN_DDR_S3-63 ………………………………………………………………………………………………...

  • Page 4: Camera Specification

    - Digital Zoom :·Still Image mode : 1.0X ~ 5.0X ·Play mode : S730: 1.0X ~ 12.0X (depends on image size) S630: 1.0X ~ 11.0X (depends on image size) LCD Monitor - 2.5" color TFT LCD (S730:230K dots, S630:150K dots) Focusing - Type : TTL auto focus - Range...
  • Page 5 2816X2112 2784X1856 2816X1584 2048X1536 1024X768 - Capacity (256 MB MMC) ·S730 Super Fine Fine Normal ·S630 Super Fine Fine Normal ※ These figures are measured under Samsung’ s standard conditions and may vary depending on shooting conditions and camera settings.
  • Page 6 Ⅰ. SPECIFICATION “ “ E” ” Button - Effect : Color, Image Adjust, Fun (Highlight, Composite ,Photo Frame) - Editing : Resize, Rotate, Color, Special Color, Image Adjust (Brightness, Contrast, Saturation, Add Noise), Fun (Cartoon, Highlight, Composite, Photo Frame, Sticker) Image Play - Single image, Thumbnails, Slide show, Movie Clip Interface...

  • Page 7: System Requirements

    Ⅰ. SPECIFICATION 2. System Requirements For Windows For Macintosh PC with processor better than Pentium II 450MHz Power Mac G3 or later (Pentium 700MHz recommended) Windows 98/98SE/2000/ME/XP Mac OS 9.2~10.3 Minimum 64MB RAM Minimum 64MB RAM 200MB of available hard disk space 110MB of available hard-disk space USB port USB port...

  • Page 8: Lcd Monitor Indicator

    Ⅰ. SPECIFICATION 3. LCD monitor indicator ■ Recording mode ① ⑳ ⑲ ⑱ ⑰ ② ⑯ ③ ⑮ ④ ⑭ ⑤ ⑬ ⑥ ⑫ ⑦ ⑪ ⑧ ⑨ ⑩ [ Image & Full Status ]...
  • Page 9 Self-timer Macro Contrast Sharpness Auto focus frame Camera shake warning Date/ Time 2007/01/01 01:00 PM Exposure compensation White Balance S730 S630 S730 Continuous shot S630 Metering Image quality S730 Image size S630 Battery Optical/ Digital Zoom bar / Digital Zoom rate...
  • Page 10 Ⅰ. SPECIFICATION ■ Play mode ⑬ ⑫ ⑪ ① ② ③ ⑩ ④ ⑨ F2.8 ⑧ 1/250 ⑦ FLASH ⑥ SIZE 3072X2304 ⑤ DATE 2007/01/01 Description Icon Play mode icon Voice Memo Protect DPOF Recording date 2007/01/01 3072X2304 ~ 256X192 Image size ON/OFF Flash...
  • Page 11 Ⅰ. SPECIFICATION 4 4 . . C C O O N N N N E E C C T T I I O O N N D D I I A A G G R R A A M M SD Card Card Reader Lap top...

  • Page 12: Identification Of Features

    Ⅰ. SPECIFICATION 5. IDENTIFICATION OF FEATURES Front & Top Mode dial Power button Shutter button Speaker Flash Self-timer lamp / Auto focus lamp USB / AV connection terminal Lens / Lens cover DC input connection port Microphone Back & Bottom Camera status lamp Zoom T button (Digital zoom)
  • Page 13 Ⅰ. SPECIFICATION Bottom/ 5-function button Battery chamber cover Memory card slot Battery chamber Voice memo/ Voice Recording/ Up button Menu/ OK button Flash/ Self-timer/ Left button Right button Macro/ Down button Play & Pause button...

  • Page 14: Main Assembly

    Ⅱ. EXPLODED VIEW AND PART LIST 1. MAIN ASSEMBLY...

  • Page 15: Body Assembly

    Ⅱ. EXPLODED VIEW AND PART LIST 2. BODY ASSEMBLY 2-37 2-38 2-36 2-32 2-33 2-35 2-19 2-20 2-21 2-22 2-23 2-24 2-29 2-26 2-30 2-28 2-40 2-34 2-18 2-27 2-25 2-31 2-12 2-11 2-15 2-17 2-29 2-10 2-17 2-13 2-14 2-16 2-39 2-17...

  • Page 16: Barrel Assembly

    Ⅱ. EXPLODED VIEW AND PART LIST 3. BARREL ASSEMBLY 3-41 3-14 3-42 3-23 3-24 3-40 3-13 3-25 3-12 3-10 3-19 3-24 3-16 3-20 3-15 3-24 3-21 3-17 3-22 3-26 3-18 3-37 3-11 3-36 3-35 3-34 3-32 3-33 3-31 3-28 3-30 3-29 3-38 3-39...
  • Page 17 Ⅱ. EXPLODED VIEW AND PART LIST 4. BARREL ASSEMBLY...

  • Page 18: Front Cover Assembly

    Ⅱ. EXPLODED VIEW AND PART LIST 5. FRONT COVER ASSEMBLY 5-13 5-12 5-10 5-11...

  • Page 19: Middle Cover Assembly

    Ⅱ. EXPLODED VIEW AND PART LIST 6. MIDDLE COVER ASSEMBLY 6-10 6-11 6-12...

  • Page 20: Back Cover Assembly

    Ⅱ. EXPLODED VIEW AND PART LIST 7. BACK COVER ASSMEBLY...

  • Page 21: Packing Item

    Ⅱ. EXPLODED VIEW AND PART LIST 8. PACKING ITEM 8-12 8-13 8-14 8-19 8-16 8-17 8-18 8-10 8-15 8-11...
  • Page 22 OLD S630(D60) STS3-63 SHARP(6 L) PART CODE MAIN_PCB AD92-00367A AD81-00217A LCD_FRAME AD81-02817A NEW S630(D60) STS3 VE SEC PART CODE MAIN_PCB AD92-00368A AD07-00076A LCD_FRAME AD97-13896A...
  • Page 23 OLD S730(D70) STS3-73 Parts Name Parts Code MAIN PCB AD92-00333A AD07-00069A LCD_FRAME AD61-03156A 0605-001128 CCD_FPCB ASSY AD92-00363A NEW S750(S730VE,D70VE,D75) STS3 VE SEC Parts Name Parts Code MAIN PCB AD92-00334A AD07-00076A LCD_FRAME AD97-13896A 0605-001134 CCD_FPCB ASSY AD92-00364A...
  • Page 24 Fig.No Old Parts Code New Parts Code Parts Name Q'ty Supply Remarks 1.MAIN ASSEMBLY Q7304000201A AD63-01886A DC_USB_COVER BLACK Q7304000201B AD63-01887A DC_USB_COVER SILVER Q7304000201C AD63-01888A DC_USB_COVER Q7304000201D AD63-01889A DC_USB_COVER PINK Q7304000201E AD63-01890A DC_USB_COVER GREEN Q7304000201F AD63-01891A DC_USB_COVER_S73 GREEN Q7304000201G AD63-01892A DC_USB_COVER_S73 BLUE Q7304000201H AD63-01893A DC_USB_COVER_S73 FUNKY PINK...
  • Page 25 2-34 Q7409261901A DNA TOP_PLATE_SHIELD_FORM Q9008116801A AD92-00367A MAIN_PCB_S630/D60 Q9008113301A AD92-00333A MAIN_PCB_S730/D70 2-35 Q9008116802A AD92-00368A MAIN_PCB_S630VE/D60VE Q9008113302A AD92-00334A MAIN_PCB_S730VE/S750/D75/D70VE/S73 Q7011061701A AD81-02817A LCD_FRAME_S630 2-36 Q7011059001A AD61-03156A LCD_FRAME_S730 Q9001130001A AD97-13896A LCD_FRAME_SEC_S630VE/S730VE/D70VE/D60VE/S750/S73 2-37 Q9761174007 DNA SC_1740 Q0704014101A AD81-00217A LCD_S630/D60 2-38 Q0704013601A AD07-00069A LCD_S730/D70 Q0704014501A AD07-00076A LCD_S630VE/S730VE/D60VE/D70VE/S750/D75/S73 1 2-39 Q7012094701A AD81-02888A FRONT_DECORING_BLACK Q7012087203A AD64-01754A FRONT_DECORING_SILVER 2-40 Q9004089301A DNA...
  • Page 26 Q9002139601A AD97-13418A BARRIER LEVER ASS'Y Q6107064202A AD81-07593A BARRIER OPEN SPRING Q6003047001A DNA BARRIER SCREW Q9002146701A AD97-13456A BARRIER ASSY 5.FRONT COVER ASSEMBLY Q7217395801A DNA FRONT_COVER_S630 Q7217393601A DNA FRONT_COVER_S730 Q7217404001A DNA FRONT COVER_D60 Q7217403901A DNA FRONT COVER_D60 Q7117017401A DNA FRONT_DECO_S630/S730 Q7104002601A DNA FRONT_DECO_D60/D70 Q7217372502A AD64-01850A AF_LED_WINDOW Q7217395701A AD64-01908A GRIP_DECO...
  • Page 27 Q9007272001A AD97-14371A MODE_CONTACT_ASSY_SL73 Q9761173007A DNA SC_1730 Q9008113401A DNA MODE_FPCB_ASSY Q7011059101A DNA TOP_KEY_PLATE Q0961900301A 6003-001630 SC_1430 6-10 Q7217395101A AD61-03470A STRAP_INNER_HOLDER 6-11 Q3001001302A AD81-00527A SPEAKER 6-12 Q9007278201A AD97-14502A TOP_KEY_ASSY 7.BACK COVER ASSMEBLY Q7217397201A DNA BACK_COVER_S630/D60 Q7217393701A DNA BACK_COVER_S730/D70 Q7409275201A AD63-02201A LCD_SPONGE_A Q7409275302A AD63-02202A LCD_SPONGE_B Q7211087801A DNA ZOOM_LEVER Q7217394901A AD64-01900A NAVI_KEY...
  • Page 28 MIC LABEL KENOX D70 (MADE IN CHINA) Q7409279101A DNA MIC LABEL KENOX D60 (MADE IN CHINA) Q7409278801A DNA FCC LABEL SAMSUNG D70 (MADE IN CHINA) Q7409279201A DNA FCC LABEL SAMSUNG D60 (MADE IN CHINA) Q7409278901A DNA FCC LABEL SAMSUNG D70 (MADE BY SAMSUNG)
  • Page 29 Ⅲ. ADJUSTMENT 1. FIRMWARE 1) RESTING CAMERA 1. Turn on the Camera 2. Press and hold the Up button and Shutter button and then press the Power off. 3. Turn on the camera and check whether the camera is reset or not.
  • Page 30 Ⅲ. ADJUSTMENT 2) CHECKING VERSION 1. Remove the memory card from the camera. 2. Turn on the camera. 3. Press the Up button twice to select the Voice Recording mode. 4. Press the 5 function button as following order. (Left button → Right button → UpÄbutton → +/- button)
  • Page 31 Ⅲ. ADJUSTMENT 5. Check the Firmware and turn off the camera.
  • Page 32 Ⅲ. ADJUSTMENT 3) UPGRADING 1. Insert the SD card that has the firmware. * Updating the firmware will delete all data in the SD card. Be sure to download all data to your PC before updating the firmware. The firmware file name must be " STS373.elf " and use the AC adapter or fully charged battery. 2.
  • Page 33 Ⅲ. ADJUSTMENT 5. Press the 5 function button as following order. (Left button → Right button → Up button → +/- button) 6. 'UPGRADE (UP TYPE)' message will display and then the firmware will be upgraded. 7. After upgrading the firmware, the camera is turned off. 8.
  • Page 34 Ⅲ. ADJUSTMENT 4) FULL VERSION OF FIRMWARE How to use the FULL firmware1 ▷ Camera Status : When turning on the camera, the power consumption (Checking the POWER SUPPLY) is 200-300mA and the camera cant be operated. ▷ Cause : The data of 0 address in the FLASH MEMORY of the MAIN PCB is damaged. ▷...
  • Page 35 Ⅲ. ADJUSTMENT How to use the FULL firmware2 Depending on the camera status, do the full version upgrade. ▷ Reference : - Delete all data in the memory card and upgrade with this firmware. - When using the full version upgrade, back up the script file as the files will be deleted by the upgrade. - If the full version upgrade is done by the following way, the script files are saved on the SD card.
  • Page 36 Ⅲ. ADJUSTMENT 5. Press the 5 function button as following order. (Left button → Right button → Down button → +/- button)
  • Page 37 Ⅲ. ADJUSTMENT 6. 'UPGRADING!' message will display and then the firmware will be upgraded.
  • Page 38 Ⅲ. ADJUSTMENT - After completing the upgrading,Äback upÄfiles will be made on the SD memory card. Backup file names areÄLSCLUT0.BIN, DefectivePixel0.bin and DefectivePixel1.bin . 7. After upgrading the Full version firmware, upload the script files. Turn on the camera and press the Up button twice to select the Voice Recording mode. Press the 5 function button as following order : Tele button →...
  • Page 39 Ⅲ. ADJUSTMENT 8. The following message will display and the upgrading is complete. 9. Turn off the camera.
  • Page 40 Ⅲ. ADJUSTMENT 2. ADJUSTMENT CAUTION 1) Basic Information of Adjustment After changing the electronic parts of S730, the parts have to be adjusted in accordance withe the adjusted items. The items listed on the table are have to be adjusted after changing. 1>...
  • Page 41 Ⅲ. ADJUSTMENT 3> Adjustment program file To adjust all items, all kinds of code by items have to be inserted in program file and saved them to the SD card as TXT file type. The codes are listed below. < Description of TXT file > Use the Memo pad of Basic Windows program and save it as Ä"STS373ADJ.txt"...
  • Page 42 Ⅲ. ADJUSTMENT //======================================#2.LSC //mode program //adj_lens_shading repeat_num 1 adj_lens_shading ng_repeat 3 adj_lens_shading lut_load_percent 80 adj_lens_shading before_capture_skip 1 adj_lens_shading luma_min_max 75 120 adj_lens_shading run delay 10 //adj_control signal 100 //======================================#3.Battery Level adj_battery base 100 300 adj_battery half_1 175 adj_battery low_1 169 adj_battery empty_1 165 adj_battery lock_1 161 adj_battery start_1 165...
  • Page 43 Ⅲ. ADJUSTMENT adj_sh_close gain_offset -5 //(5000K -> 3300K) adj_sh_close gain_adjustrange1 15 adj_sh_close gain_adjustrange2 15 adj_sh_close run delay 10 //adj_control signal 1500 //======================================#6.Strobe Mode program Ae metering 1 Ae iso 2 Ae evc 6 Ae preview_fnum 1 Ae preview_s_speed 058 Ae preview_gain 050 Ae lock Zoom wide Delay 20...
  • Page 44 Ⅲ. ADJUSTMENT adj_punt searching_min_short 80 80 80 80 90 90 50 50 adj_punt searching_max_short 160 160 160 160 165 170 170 170 adj_punt searching_min -7 31 23 21 27 29 18 32 adj_punt searching_max 245 248 240 238 244 246 235 230 adj_punt limit_min_short 85 85 85 85 95 95 55 55 adj_punt limit_max_short 155 155 155 155 160 165 165 165 adj_punt limit_min 13 51 43 41 47 49 38 52...
  • Page 45 Ⅲ. ADJUSTMENT adj_burnin flash_cap adj_burnin flash_off_cap adj_burnin norm_cap adj_burnin macro_cap adj_burnin selftimer_cap adj_burnin play_mode adj_burnin prog_mode adj_burnin avi_cap_5sec adj_burnin easy_mode adj_burnin aux_led_on adj_burnin wait_2sec adj_burnin aux_led_off adj_burnin burnin_end //================================#2. CCD Defect Cell //start adj_defective_pixel //adj_control check_process_id 65535 //adj_control save_e2prom 1 //adj_control save_data_file 1 mode program //ae metering multi...
  • Page 46 Ⅲ. ADJUSTMENT 2) OB SETTING After changing the MAIN PCB, adjust the black color. < How to adjust > a...Download program and save it to SD memory card. b...Insert the SD memory card that has the program file and turn on the camera. c...Adjustment will be done automatically.
  • Page 47 Ⅲ. ADJUSTMENT //======================================#1. OB delay 5 mode program adj_ob preview_agc 96 adj_ob preview_target_rgb 0 0 0 adj_ob preview_luma_min_max 150 4000 adj_ob capture_agc 96 adj_ob capture_target_rgb 0 0 0 adj_ob capture_luma_min_max 150 4000 adj_ob run delay 5 //adj_control signal 100// start signal poweroff zoom_close...
  • Page 48 Ⅲ. ADJUSTMENT 3) LENS SHADING The characteristic of Lens makes the outside of the image be dark. This phenomenon is called “Lens Shading”. This adjustment is for compensating the brightness of the outside of the image. After calculating the darkness, this adjustment will increase the brightness of the outside of the image up to 80% of the center of the image.
  • Page 49 Ⅲ. ADJUSTMENT e...Turn on the camera. f...Adjustment will be done automatically. e...After completing the upgrade, the camera is turned off automatically. < Description of TXT file > When making or modifying the program, see the following program codes. When modify the program, use the Memo Pad of Windows and save it as "STS373ADJ.txt" // PM Batch Test 8 // // adj control adj_control check_process_id 65535...
  • Page 50 Ⅲ. ADJUSTMENT 4) B/T LEVEL ADJ After changing the MAIN PCB, adjust WARNING LEVEL and LOCK LEVEL. < How to adjust > a...Prepare the POWER..SUPPLY. b...Connect the camera to the POWER..SUPPLY. c...Set the voltage to 2.71V. d...Downloading the program file and save it to SD memory card. e...Insert the SD memory card and turn on the camera.
  • Page 51 Ⅲ. ADJUSTMENT //======================================#3.Battery Level adj_battery base 100 300 adj_battery half_1 175 adj_battery low_1 169 adj_battery empty_1 165 adj_battery lock_1 161 adj_battery start_1 165 adj_battery half_2 175 adj_battery low_2 168 adj_battery empty_2 164 adj_battery lock_2 157 adj_battery start_2 165 adj_battery run poweroff zoom_close...
  • Page 52 Ⅲ. ADJUSTMENT 5) BACK LASH ADJ After changing the MAIN PCB, BARREL and CCD, adjust the BACK LASH. < How to adjust > a...Download the Program file and save it to SD memory card. b...Insert the SD memory card that has program file and turn on the camera. c...Adjustment will be done automatically.
  • Page 53 Ⅲ. ADJUSTMENT 6) SHUTTER CLOSE TIME ADJ After changing the MAIN PCB, BARREL and CCD, adjust the SHUTTER CLOSE TIME and CCD Gain. [ Standards for the Adjustment ] - Specification of the tools : Light source that can block the external light source - Color temperature : 3200K ±50 - Brightness : LV 13 ±0.1 (±0.05 recommended) <...
  • Page 54 Ⅲ. ADJUSTMENT < Description of TXT file > When making or modifying the program, see the following program codes. When modify the program, use the Memo Pad of Windows and save it as"STS373ADJ.txt" // PM Batch Test 8 // // adj control adj_control check_process_id 65535 adj_control set_process_id 65534 adj_control save_e2prom 1 // save eeprom...
  • Page 55 Ⅲ. ADJUSTMENT 7) FLASH ADJ After changing the MAIN PCB and SUB PCB, adjust the FLASH. < How to adjust > a...Arrange a 18% reflect chart in a darkroom. b...Arrange a camera in a darkroom. (Use TRIPOD) c...The distance between the reflect chart and the camera should be 80cm. d...Download the program and save it to SD memory card.
  • Page 56 Ⅲ. ADJUSTMENT < Description of TXT file > When making or modifying the program, see the following program codes. When modify the program, use the Memo Pad of Windows and save it as"STS373ADJ.txt" // PM Batch Test 8 // // adj control adj_control check_process_id 65535 adj_control set_process_id 65534 adj_control save_e2prom 1 // save eeprom...
  • Page 57 Ⅲ. ADJUSTMENT 8) FOCUS ADJ After changing the MAIN PCB and BARREL, adjust the PUNT. < How to adjust > a...Arrange a chart for adjust the FOCUS. b...Attach the camera to the tripod. c...The distance between the chart and the camera should be 80cm. Chart d...Download the program and save it to SD memory card.
  • Page 58 Ⅲ. ADJUSTMENT < Description of TXT file > When making or modifying the program, see the following program codes. When modify the program, use the Memo Pad of Windows and save it as"STS373ADJ.txt" // PM Batch Test 8 // // adj control adj_control check_process_id 65535 adj_control set_process_id 65534 adj_control save_e2prom 1 // save eeprom...
  • Page 59 Ⅲ. ADJUSTMENT //adj_control signal 0 delay 5 poweroff zoom_close...
  • Page 60 Ⅲ. ADJUSTMENT 9) CCD DEFECT ADJ After changing the MAIN PCB and CCD, adjust the DEFECT CELL of CCD. < How to adjust > a...Download program file and save it to SD memory card. b...Turn on the camera. c...Adjustment will be done automatically. d...After completing the upgrade, the camera is turned off automatically.
  • Page 61 Ⅲ. ADJUSTMENT mode program //ae metering multi //ae iso 200 //ae ev 0 //ae iris 0 //awb wbal auto //coach view //delay 25 adj_defect integration adj_defect ref_level_short 800 adj_defect ref_level_long 3500 adj_defect exp_time 6 adj_defect defect_max_num1 30000 adj_defect defect_max_num2 30000 adj_defect run //end adj_defect //delay 10...
  • Page 62 Ⅲ. ADJUSTMENT 10) BURNING ADJ After changing the MAIN PCB and parts, check whether all of the camera functions work correctly. < How to adjust > a...Download program and save it to SD memory card. b...Insert the SD memory card that has the program file and turn on the camera. c...Adjustment will be done automatically.
  • Page 63 Ⅲ. ADJUSTMENT adj_burnin prog_mode adj_burnin avi_cap_5sec adj_burnin easy_mode adj_burnin aux_led_on adj_burnin wait_2sec adj_burnin aux_led_off adj_burnin burnin_end //poweroff zoom_close...
  • Page 64 Ⅲ. ADJUSTMENT 11) EEPROM READ To read the data of EEPROM, refer to the below codes... < How to read > a...Download program and save it to SD memory card. b...Insert the SD memory card that has the program file and turn on the camera. c...Turn on the camera and the DATA in the EEPROM will be copied in the SD card.
  • Page 65 Ⅲ. ADJUSTMENT 12) EEPROM WRITE If you want to write the DATA of EEPROM, do as follows. < How to read > a...Insert the address and valueÄand save the program in the SD card. Ex) adj_check e2p_writeÄ301, 113 b...Insert the SD card to the camera and turn on the camera. c...Turn on the camera and the data of EEPROM will be copied to the camera.
  • Page 66 Ⅳ. PATTERN DIAGRAM 1. PARTS ARRANGEMENT FOR EACH PCB ASS’Y 1) MAIN_TOP_S3-63...
  • Page 67 Ⅳ. PATTERN DIAGRAM 2) MAIN_BOTTOM_S3-63...
  • Page 68 Ⅳ. PATTERN DIAGRAM 3) CCD_TOP_S3-63...
  • Page 69 Ⅳ. PATTERN DIAGRAM 4) CCD_BOTTOM_S3-63...
  • Page 70 Ⅳ. PATTERN DIAGRAM 5) MAIN_BOTTOM_S3-73...
  • Page 71 Ⅳ. PATTERN DIAGRAM 6) MAIN_BOTTOM_S3-73...
  • Page 72 Ⅳ. PATTERN DIAGRAM 7) CCD_TOP_S3-73...
  • Page 73 Ⅳ. PATTERN DIAGRAM 8) CCD_BOTTOM_S3-73...
  • Page 74 Ⅳ. PATTERN DIAGRAM 9) STROBO_TOP_S3-63/S3-73...
  • Page 75 Ⅳ. PATTERN DIAGRAM 10) STROBO_BOTTOM_S3-63/S3-73...
  • Page 76 Ⅳ. PATTERN DIAGRAM 11) MODE_TOP_S3-63/S3-73...
  • Page 77 Ⅳ. PATTERN DIAGRAM 12) MODE_BOTTOM_S3-63/S3-73...
  • Page 78 Ⅴ. CIRCUIT DIAGRAM 1) MAIN_S3-63...
  • Page 79 Ⅴ. CIRCUIT DIAGRAM 2) MAIN_DDR_S3-63...
  • Page 80 Ⅴ. CIRCUIT DIAGRAM 3) MAIN_CCD_S3-63...
  • Page 81 Ⅴ. CIRCUIT DIAGRAM 4) MAIN_I/O LCD_S3-63...
  • Page 82 Ⅴ. CIRCUIT DIAGRAM 5) MAIN_KEY_S3-63...
  • Page 83 Ⅴ. CIRCUIT DIAGRAM 6) MAIN_LENS(MOTOR)_S3-63...
  • Page 84 Ⅴ. CIRCUIT DIAGRAM 7) MAIN_POWER_S3-63...
  • Page 85 Ⅴ. CIRCUIT DIAGRAM 8) MAIN_STROBO_S3-63...
  • Page 86 Ⅴ. CIRCUIT DIAGRAM 9) MAIN_S3-73...
  • Page 87 Ⅴ. CIRCUIT DIAGRAM 10) MAIN_DDR_S3-73...
  • Page 88 Ⅴ. CIRCUIT DIAGRAM 11) MAIN_CCD_S3-73...
  • Page 89 Ⅴ. CIRCUIT DIAGRAM 12) MAIN_I/O LCD_S3-73...
  • Page 90 Ⅴ. CIRCUIT DIAGRAM 13) MAIN_KEY_S3-73...
  • Page 91 Ⅴ. CIRCUIT DIAGRAM 14) MAIN_LENS(MOTOR)_S3-73...
  • Page 92 Ⅴ. CIRCUIT DIAGRAM 15) MAIN_POWER_S3-73...
  • Page 93 Ⅴ. CIRCUIT DIAGRAM 16) MAIN_STROBO_S3-73...
  • Page 94 Ⅴ. CIRCUIT DIAGRAM 17) STROBO_S3-63/S3-73...
  • Page 95 Ⅴ. CIRCUIT DIAGRAM 18) MODE_KEY_S3-63/S3-73...
  • Page 96 Ⅵ. SERVICE INFORMATION 1. The order of disassembly and assembly ■ Caution 1. Do the disassembling and assembling camera where the blocking static electricity mat is on the table. 2. When handling the major PCBs of camera, please wearing the band which cuts off the electric current on the wrist.
  • Page 97 Ⅵ. SERVICE INFORMATION ■ ■ Disassembly 1. Remove 2 screws. 2. Remove 2 screws. 3. Remove 4 screws.
  • Page 98 Ⅵ. SERVICE INFORMATION 4. Disassemble the BACK COVER. 5. Remove 1Äscrew.
  • Page 99 Ⅵ. SERVICE INFORMATION 6. Disconnect the PCB from the connector. 7. Disassemble the LCD ASSY.
  • Page 100 Ⅵ. SERVICE INFORMATION 8. Remove 1Äscrew. 9. Disconnect the PCB from the connector.
  • Page 101 Ⅵ. SERVICE INFORMATION 10. Disassemble the FRONT COVER. Discharging point : Before removing the PCB soldering, discharge the main condenser.
  • Page 102 Ⅵ. SERVICE INFORMATION 12. 1st. Removing the PCB soldering and disassemble the 2 connectors. 2nd. Remove the 2 soldering points of battery contacts. 3rd. Disassemble the 2 wires. 13. Disassemble the MAIN PCB.
  • Page 103 Ⅵ. SERVICE INFORMATION 14. Remove 1Äscrew. 15. Disassemble the STROBE PCB.
  • Page 104 Ⅵ. SERVICE INFORMATION 16. Remove 2 screws. 17. Remove 2 screws.
  • Page 105 Ⅵ. SERVICE INFORMATION 18. Disassemble the Barrel. 19. Complete.

This manual is also suitable for:

S730

Table of Contents