Nibe S1155 User Manual
Ground source
Hide thumbs
Also See for S1155:
- Installer manual (96 pages) ,
- User manual (16 pages) ,
- Safety information manual (12 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nibe S1155
Summary of Contents for Nibe S1155
- Page 1 UHB EN 2001-2 USER MANUAL 531111 Ground source heat pump NIBE S1155/S1255...
- Page 2 When there is new software to download, you S1155: This function page is only visible in installations can do it here (provided that S1155/S1255 is connected with a water heater.
-
Page 3: Table Of Contents
Display unit Navigation Menu types Menu system 4 myUplink Specification Connection Range of services Mobile apps for myUplink 5 Maintenance of S1155/S1255 Regular checks Saving tips 6 Disturbances in comfort Info-menu Manage alarm Only additional heat Contact information NIBE S1155/S1255... -
Page 4: Important Information
1.9.1.1 heating curve (curve slope) Serial number must always be given Certification that the installation is carried out according to instructions in the accompanying installer manual and applicable regulations. Date ______________________________ Signed __________________________________________ Chapter 1 | Important information NIBE S1155/S1255... -
Page 5: Serial Number
Mellan dig som privatperson och företaget du köpt S1155/S1255 av gäller konsumentlagarna. För full- ständiga villkor se www.konsumentverket.se. Mellan NIBE och det företag som sålt produkten gäller AA VVS. I enlighet med denna lämnar NIBE tre års produktgaranti till företaget som sålt produkten. Produktgarantin ersätter inte höjd energiförbrukning eller skada som uppkommit... -
Page 6: Heat Pump Function
The heating medium circulates in a closed sys- tem and transports the heated water's heat energy to the house water heater and radiat- ors/heating coils. Chapter 2 | Heat pump function NIBE S1155/S1255... -
Page 7: Control - Introduction
5 seconds. • is blue when S1155/S1255 is switched off. You can activate the emergency mode both when S1155/S1255 is running and when it is switched off. • flashes white during active notice. To activate when S1155/S1255 is running: press and If the status lamp is red, you receive information and hold the on/off button for 2 seconds and select "emer-... -
Page 8: Navigation
Navigation FACTORY SETTING Factory set values are marked with *. S1155/S1255 has a touchscreen where you simply Your installer may have chosen other values that suit navigate by pressing and dragging with your finger. your system better. SELECT Most options and functions are activ- ated by lightly pressing on the display with your finger. - Page 9 When there is new software to download, you can do it here (provided that S1155/S1255 is connected to myUplink). Press the icons on the menu's lower edge for more in- 13.45 3 October...
-
Page 10: Menu System
(accessory is required). Menu 2 – Hot water 13.45 3 October You make settings for hot water operation here. S1155: This menu is only visible in installations with Your system is working properly. Do you want help making water heaters. changes? Menu 3 - Info Yes please, take me to Smartguide. -
Page 11: Myuplink
• wireless network or network cable The base level allows you to monitor the system, man- age alarms and read diagrams containing information • Internet connection to which S1155/S1255 can be for the last month. connected If you want to read older information, as well as receive •... -
Page 12: Maintenance Of S1155/S1255
The thermo- stats slow the flow in the heating system, which Your heat pump is basically maintenance free and S1155/S1255 wants to compensate by increasing the therefore requires minimal care after commissioning. temperature. It will then work harder and consume However, it is recommended that you check your install- more energy. -
Page 13: Disturbances In Comfort
LOW HOT WATER TEMPERATURE OR A play. S1155/S1255 has no contact with the outdoor temperature sensor. Calculated flow line temperature is set to min. flow line. If a higher temperature is desired then min. flow line can be temporarily changed in menu 1.30.4. Check the LACK OF HOT WATER connection to the outdoor temperature sensor and reset the alarm. -
Page 14: Only Additional Heat
• There is no heating or cooling demand (accessory is required for cooling). • Closed thermostats in several rooms. – S1155/S1255 does not call on heating, cooling or hot wa- – Set the thermostats to max in as many rooms as possible. ter. - Page 15 Emergency mode You can activate the emergency mode both when S1155/S1255 is running and when it is switched off. To activate when S1155/S1255 is running: press and hold the on/off button for 2 seconds and select "emer- gency mode" from the shutdown menu.
-
Page 19: Contact Information
Tel: +46 (0)433-27 3000 kuzmin@evan.ru info@nibe.se nibe-evan.ru nibe.se SWITZERLAND NIBE Wärmetechnik c/o ait Schweiz Industriepark, CH-6246 Altishofen Tel. +41 (0)58 252 21 00 info@nibe.ch nibe.ch For countries not mentioned in this list, contact NIBE Sweden or check nibe.eu for more information. - Page 20 WS release date: 2019-10-28 15:02 Publish date: 2019-12-18 13:32 This manual is a publication from NIBE Energy Systems. All product illustrations, facts and data are based on the available information at the time of the publication’s approval. NIBE Energy Systems makes reservations for any factual or printing errors in this manual.