Advertisement
Secure unstable workpieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
DO NOT use the drill for a task that it is not designed to perform.
8
DO NOT allow untrained persons to operate the drill.
8
DO NOT get the drill wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT operate the drill if it is damaged.
8
DO NOT use drill in an area where paint fumes, solvents or flammable liquids pose a potential hazard. Keep flammable material away
8
from the drill when operating. Flammable waste, such as wipes or cleaning rags, must be placed in a closed metal container and disposed of
correctly.
DO NOT exceed the rated capacity of the drill.
8
DO NOT operate the drill if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT leave the drill operating unattended.
8
DO NOT operate the drill when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT pull the cable from the power supply.
8
When not in use switch off the drill, remove the plug from the power supply and DO NOT leave until the chuck has come to a complete
9
stop.
2.
INTRODUCTION
i
Variable speed model allows stepless control of drilling speed between minimum and maximum enabling finer control of finish and tolerance. The
belt transmission uses two spring tensioned cone pulleys, the diameters of which can be adjusted by moving a centre idle pulley with the speed
adjustment control lever. Safety devices fitted include a no-volt release switch, allowing insurance company approval for use in educational
establishments. Supplied with chuck guard.
3. SPECIFICATIONS
Model No:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GDM200F/VS
Drilling Capacity (Chuck Size): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16mm
Spindle Nose Taper: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MT2
Spindle Centre to Column: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178mm
Spindle Travel: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80mm
Number of Speeds: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Variable
Speed Range: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150-2300rpm
Maximum Distance Spindle to Table:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 730mm
Maximum Distance Spindle to Base: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1170mm
Working Table Surface Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Ø310mm
Working Base Surface Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 x 220mm
Overall Base Size:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 460 x 275mm
Column Diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80mm
Collar Diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60mm
Overall Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1630mm
Motor Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650W
Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71kg
Duty Cycle: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S2
Optional Keyless Chuck 16mm: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .GDMX/KC
4. CONTENTS
4.1.
Package content
Unpack the parts listed below and check to ensure they are in good condition. Any queries must be reported to your stockist
immediately.
Head Assembly
Column with Flange
Base
Table
Table Arm
Table Bracket and Worm
Rack and Rack Ring
5. ASSEMBLY
Note:
Figures are illustrative and may differ in detail from your drill.
5.1.
Assembly
5.1.1.
Place the column assembly on the base, align holes and secure with the four bolts provided.
5.1.2.
Insert the worm gear (fig.1.1) into the table bracket crank handle hole, ensuring that the worm
gear meshes with the rack gear in the bracket.
5.1.3.
Screw the lock handle (fig.1.2) into the lugs at the rear of the table bracket but DO NOT tighten.
5.1.4.
Install the table bracket onto the column together with the rack (fig.2), engaging gear in bracket with
rack teeth. Note that the rack should be assembled with the longer tooth-free end uppermost.
.
Install the rack collar and tighten grub screw firmly (fig.3). Ensure that rack is free to move around column.
5.1.5.
Install the table adjusting handle (fig.3.A) onto the worm gear shaft, tightening the grub screw onto the flat on the shaft.
5.1.6.
Tighten the table bracket lock handle (fig.3.B).
5.1.8.
Fit the table arm to the table bracket with the bolt and washer provided (fig.2.D).
© Jack Sealey Limited
Feed Handles and Knobs (3)
Pivoted Lock Handle (2 - table arm & bracket)
Adjusting Handle with Set Screw (table)
Bolt and Washer (table arm)
Bolts (4 - column)
Chuck and Key
Arbor
Original Language Version
Speed Control Handle
Safety Guard
Set Screws (2 - head)
Screw and Washer (pulley cover)
Wedge
Hex. Keys (2)
fig.1
GDM200F/VS Issue:3 (3) - 31/08/18
Advertisement
