Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction
Wear eye
manual
protection
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or is
8
replaced immediately by a qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
GENERAL SAFETY
WARNING! Disconnect drill from mains power before changing accessories, servicing or performing
any maintenance.
Maintain the drill in good condition (use an authorised service agent).
9
WARNING! Keep all guards and holding screws in place, tight and in good working order. Check regularly for damaged
parts. A guard, or any other part, that is damaged must be repaired or replaced before the tool is next used, to ensure that it
will operate properly and perform its intended function. The safety guard is a mandatory fitting where the drill is used on
premises covered by the Health & Safety at Work Act.
Check alignment of moving parts and check for possible broken parts.
9
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Ensure that the head frame set screws are tight before using the drill.
9
Secure the drill to a supporting structure to avoid the machine tipping, sliding or walking. Drill is designed for use with drill bits and
9
mortice attachments only. No other accessory may be used.
Ensure the chuck is securely fastened to the spindle.
9
Remove chuck keys and wrenches from the machine and work area before switching on.
9
Use clamps or a vice (not included but available from your Sealey stockist). DO NOT secure the workpiece by hand.
9
Refer to speed chart for recommended drilling speeds.
9
WARNING! Always wear approved eye or face protection when operating this drill. Use a face or dust mask if dust is
generated.
Others in the workplace should keep a safe distance from the drill, especially when it is in operation.
9
Keep drill bits clean and sharp for best and safest performance. Follow the instructions for lubrication and changing accessories.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Locate drill in a suitable work area and keep area clean and tidy and free from unrelated materials. Ensure that there is adequate lighting.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
© Jack Sealey Limited
INSTRUCTIONS FOR:
VARIABLE SPEED PILLAR DRILL
GDM200F/VS
MODEL NO:
Wear protective
Wear ear
gloves
protection
Original Language Version
Wear a mask
Indoor use only
Recommended fuse
rating: 13A