Reverse Mowing Option (Rmo); Pto Switch; Ignition Switch; Brake Pedal - Simplicity Broadmoor Series Operator's Manual

Features & Controls

Reverse Mowing Option (RMO)

The Reverse Mowing Option allows for mowing (or use of
other PTO driven attachments) while traveling in reverse.
If you choose to mow or operate another attachment in
reverse, turn the RMO key after the PTO is engaged. The
L.E.D. light will illuminate, and the operator can then mow
in reverse. Each time the PTO is disengaged the RMO
needs to be reactivated if desired.

PTO Switch

¾»  ÅÍ»È ·Á» 
gages attachments that use the PTO. To engage the PTO,
pull UP on the switch. Push DOWN to disengage. ÅÊ» ʾ·Ê
ʾ» ÅƻȷÊÅÈ ÃËÉÊ ¸» É»·Ê»º ÈÃÂÏ ¿Ä ʾ» ÊÈ·¹ÊÅÈ É»·Ê ¼ÅÈ Ê¾»
 ÊÅ ¼ËĹʿÅÄ

Ignition Switch

The ignition switch starts and stops the engine, it has three
positions:
OFF Stops the engine and shuts off the
electrical system.
RUN Allows the engine to run and powers the
electrical system.
START Cranks the engine for starting.
 »Ì»È »·Ì» ʾ» ¿½Ä¿Ê¿ÅÄ ÉͿʹ¾ ¿Ä ʾ»  ÆÅÉ¿Ê¿ÅÄ
Ϳʾ ʾ» »Ä½¿Ä» ÉÊÅÆÆ»º ʾ¿É ºÈ·¿ÄÉ Ê¾» ¸·ÊÊ»ÈÏ

Brake Pedal

Depressing the brake pedal applies the tractor brake.
Ground Speed Pedals
The tractor's forward ground speed is controlled by the
forward ground speed control pedal. The tractor's reverse
ground speed is controlled by the reverse ground speed
control pedal.
Depressing either pedal will increase ground speed. Note
that the further down the pedal is depressed, the faster the
tractor will travel.
Parking Brake
The parking brake knob is used to lock the parking brake
when the tractor is stopped. Fully depressing the brake
pedal and pulling up on the knob engages the parking
brake.
12
ÉͿʹ¾ »Ä½·½»É ·Äº º¿É»Ä-
Mower Height of Cut Adjustment
The cutting height adjustment switch controls the mower
¹ËÊʿĽ ¾»¿½¾Ê ¾» ¹ËÊʿĽ ¾»¿½¾Ê ¿É ¿Ä Ä¿Ê»ÂÏ ·ºÀËÉÊ·¸Â»
between 1.0" and 4.0" (2,5 and 10,2 cm).
Attachment Lift Control Lever
¾»Ä ËɿĽ ʾ» ÃÅÍ»È º»¹Á ¿¼Ê ʾ» º»¹Á Šʾ» ½ÈÅËĺ
while transporting to and from the job site. DO NOT cut with
the mower in the raised, transport position.
The attachment lift control lever raises and lowers attach-
ments that utilize the tractor's manual lift linkage. To lower
an attachment: pull the lever back slightly, depress the
release button, and push the lever forward until it locks
in the lowered position. To raise an attachment: push the
lever forward slightly, depress the release button, then pull
the lever back until it locks in the raised position.
Cruise Control
The cruise control is used to lock the ground speed con-
trol in forward. Move the lever forward until the desired
ground speed is reached. To disengage the cruise control
move the lever back. In the event you need to stop quickly,
depressing the brake pedal will also return the cruise con-
trol to neutral.
Seat Adjustment Lever
The seat can be adjusted forward and back. Move the
lever, position the seat as desired, and release the lever to
lock the seat into position.
Transmission Release Lever
The transmission release lever deactivates the transmis-
sion so that the tractor can be pushed by hand. See
PUSHING THE TRACTOR BY HAND section.
Fuel Tank
To remove the cap, turn counterclockwise. On models with
a dashboard display, the fuel gauge is part of the dash-
board. Models without a dashboard display have a fuel
gauge located under the seat.
Volt Power Outlet
The power outlet is 12V-DC. Accessory must be rated at 14
amps or less.