Download Print this page

Mr. Nixie Jenny reloaded Assembly And Mounting Instructions

Iv-11/15 vfd clock

Advertisement

Quick Links

Aufbau- und Montageanleitung IV
IV-11/15
IV
IV
IV
Herzlichen Glückwunsch zum Erwerb Ihres neuen Uhren-Bausatzes.
Für einen erfolgreichen Zusammenbau sind einige Grundregeln zu beachten.
• Dieser Bausatz richtet sich an den fortgeschrittenen Bastler. Erfahrungen in der Elektronik
sind hierbei unerlässlich.
• Wenn Sie merken, dass der Bausatz für Sie zu kompliziert ist, versuchen Sie bitte nicht, ihn
„zusammenzuschustern". Dies endet in der Regel in einem nicht mehr reparablen Gerät.
Bitte wenden Sie sich so früh wie möglich an den
kann.
• Bitte nehmen Sie mindestens 3 S tunden Zeit. Einen Bausatz in Hektik zusammenzulöten,
erzeugt letztendlich nur Frust – und die Fehlersuche dauert hinterher „ewig".
• Ihr Arbeitsplatz sollte sauber, aufgeräumt und gut ausgeleuchtet sein.
• Entsprechendes Elektronikerwerkzeug wie Schraubendrehersatz, Seidenschneider, Spitz-
zange und Pinzette sollte sich in Griffnähe befinden.
• Nur eine temperaturgeregelte Elektronik-Löt station mit max. 1 mm runder S pitze samt
entsprechendem bleifreien dünnem Lötzinn verwenden; sehr gute Erfahrung wurde mit
Lötzinn Iso-Core EL Sn95,5 Ag3,8 Cu0,7 mit 0,5 mm Ø und 3,5% Flussmittel von Felder
Löttechnik und 400°C Löttemperatur gemacht. W ir empfehlen jedoch die Verwendung von
verbleitem Lötzinn.
• Für den Funktionstest benötigen Sie ein Multimeter mit einem Messbereich von 50 V .
• Eine Lupe für das Lesen der Bauteilebedruckungen ist ganz hilfreich.
• Bitte halten Sie sich beim Bestücken an die in dieser Anleitung vorgegebene Reihenfolge.
Diese ist erprobt und vermindert auch das Fehlerrisiko.
• Es wird davon ausgegangen, dass Ihnen bekannt ist, dass Halbleiter (Dioden, IC's,
Transistoren) oder Elkos gepolte Bauelemente sind, eine entsprechende Markierung be-
sitzen und deshalb auch in der korrekten Richtung bestückt werden müssen.
Zusammen mit dieser Bauanleitung erhalten Sie weitere Dokumente als Download:
• Das komplette Schaltbild des Uhren-Bausatzes in Farbe.
• Die vollständige S tückliste mit Farbcodes der Widerstände.
• Eine zweisprachige Bedienungsanleitung für Ihre neue Uhr .
Wichtige Sicherheitshinweise:
Beim Aufbau, der Inbetriebnahme sowie bei Messungen und Rep araturen ist besondere
Vorsicht geboten! Der Aufbau der Schaltung geschieht auf eigene Gefahr . Die Funktions-
tüchtigkeit kann nicht garantiert werden, ebenso wenig die Eignung für bestimmte Einsatz-
zwecke. Der Anwender hat diese Eignung selbst zu überprüfen und zu verantworten. Für
Schäden, die während oder als Folge des
Haftung übernommen werden, insbesondere für Schäden, die aus mangelnder Fach-
kenntnis heraus entstehen. Die Uhr darf nur in einem berührungssicheren Gehäuse in
trockenen Innenräumen betrieben werden.
Derjenige, der einen Bausatz fertig gestellt oder eine Baugruppe durch Erweiterung bzw
Gehäuseeinbau betriebsbereit gemacht hat, gilt nach VDE 0869 als Hersteller und ist
verpflichtet, bei der Weitergabe des Geräts alle Begleitpapiere mitzuliefern und auch sei-
nen Namen nebst Anschrift anzugeben. Geräte, die aus Bausätzen selbst zusammenge-
stellt werden, sind sicherheitstechnisch wie ein industrielles Produkt zu betrachten.
Und nun, meine Dame, mein Herr – befeuern Sie Ihre Lötstation und blättern Sie um...
Ausgabe 1.2 Stand 11.12.2012 ab Serien-Nr. JR-001
-11/15
-11/15 VFD Uhr „J
-11/15
-11/15
VFD Uhr „J
VFD Uhr „J
VFD Uhr „J
VFD Uhr „Jenn
enn
enny r
enn
enn
y reloaded"
y r
y r
y r
eloaded"
eloaded"
eloaded"
eloaded"
Anbieter, der Ihnen Hilfestellung geben
Aufbaus oder Betriebs ent stehen, kann keine
Assembly- and Mounting-Instructions IV
Congratulations for purchasing this stunning clock kit.
For successful assembly of this kit please read the following helpful hints.
• This kit is designed for someone who has advanced experience with assembling
electronics.
• If you believe that the kit is too complicated for your skill level please do not try to assemble
it - this generally ends up with a device that is not repairable and results in you being very
frustrated. Please contact the provider and they can offer you other options that will end in a
more fulfilling result!
• Take your time - this kit should t ake 3 hours to complete if uninterrupted. Assembling the
kit in a hurry will lead to frustration and troubleshooting takes three times as long.
• Ensure your work area is well lit (daylight preferred) and clean.
• Electronic tools, such as pliers, small side-cutters or tweezers will be handy . You will also
need a T8 (Torx) or SW2 Allen screwdriver for the housing assembly .
• A soldering iron station with a 1 mm round tip (maximum) and a 0.8 mm (maximum) fine
electronic solder (lead-free) is required. For lead-free solder we've had good experience
with type Iso-Core EL Sn95,5 Ag3,8 Cu0,7 with 0,5 mm Ø and 3,5% Flux from Felder
Löttechnik and a 400°C soldering tip temperature; but we highly recommend to use leaded
solder tin.
• For the intermediary function test you need a multimeter with at least 50 VDC range.
• A loupe (magnifying glass) to read the small device markings is of ten helpful.
• Assemble the board in the order as st ated in the instructions - this has been proven and
will minimise mistakes.
• It is assumed that you understand that semiconductors (diodes, ICs, transistors) or
electrolytic capacitors are polarized component s. Appropriate markings are silk-screened
on the PCB and shown on the board schematic.
Together with this construction guide there are some documents you should download
• The full colour schematic of the clock kit.
• A complete part list with the colour coding of the resistors.
• A bilingual operation manual for your new clock kit.
Safety precautions:
During assembly, operation, measurement s and maintenance extra precautions must be
taken. Assemble the circuit at your own risk. The clock's functionality cannot be guaranteed
when assembled by the customer .
No responsibility can be taken for any personal claims and damages during assembly and
commission, especially for damages based on insufficient technical knowledge.
The clock may only be operated in a solid and moisture-proof enclosure.
.
The person who completes the kit and assembles this board into an enclosure for operation
is considered by the German directive VDE 0869 as a manufacturer and is required to
indicate their name and address including all documents when selling the clock.
Ready-to-go devices, which are assembled from kits, are counted as a safety-related
industrial made product.
Okay, and now, Ladies and Gentlemen – st art your soldering irons and flip the p age...
– 1 –
IV-11/15
IV
IV
IV
-11/15 VFD Cloc
-11/15
-11/15
-11/15
VFD Cloc
VFD Cloc
VFD Clock „J
VFD Cloc
k „Jenn
k „J
k „J
Issue 1.2 from 12/11/2012 valid from serial no. JR-001
k „J
enny r
enn
enn
enn
y r
y r
y reloaded"
y r
eloaded"
eloaded"
eloaded"
eloaded"

Advertisement

loading
Need help?

Need help?

Do you have a question about the Jenny reloaded and is the answer not in the manual?

Questions and answers

Summary of Contents for Mr. Nixie Jenny reloaded

  • Page 1 Aufbau- und Montageanleitung IV IV-11/15 -11/15 -11/15 -11/15 -11/15 VFD Uhr „J VFD Uhr „J VFD Uhr „J VFD Uhr „J VFD Uhr „Jenn enny r y reloaded“ eloaded“ eloaded“ eloaded“ eloaded“ Assembly- and Mounting-Instructions IV IV-11/15 -11/15 -11/15 -11/15 -11/15 VFD Cloc VFD Cloc VFD Cloc...
  • Page 2 – English text see following page –  Technische Probleme mit der Jenny Reloaded VFD Uhr    Bitte aufmerksam lesen !   Bei einigen Uhren ergab sich entweder sofort oder erst nach einiger Betriebszeit das Problem, dass  der MosFet T2 heiß wurde und die Uhr nicht mehr funktionierte. Gleichzeitig verfärbten sich  aufgrund von einem internen Kurzschluss C13 und / oder C20 und erhitzen sich stark.  Es wurde herausgefunden, dass diese Keramik‐Kondensatoren aus einer Charge stammen, die die  47 V Betriebsspannung (die Kondensatoren sind mit 50 V spezifiziert) auf Dauer nicht verkrafteten.  Bitte überprüfen Sie zuerst, mit welchen Kondensatoren Ihre Uhr ausgeliefert wurde wie folgt:    Trennen Sie die Uhr vom Strom und  schrauben Sie die Leiterplatte  heraus. Finden Sie die Positionen  von C13 und C20 anhand der Ab‐ bildungen und sehen Sie sich die  Kondensatoren an.      "Guter" Kondensator         "Schlechter" Kondensator  Ein Handeln Ihrerseits        Kondensatoren C13 und C20  ist nicht erforderlich.          müssen ausgelötet werden.    Die Uhr ist mit insgesamt acht dieser 100 nF Kondensatoren bestückt; entweder die "linke" oder  die "rechte" Ausführung. Der Ausfall betrifft jedoch nur C13 und / oder C20; d.h. dass die anderen  sechs "schlechten" Kondensatoren in der Leiterplatte belassen werden können.    Zum Auslöten der Kondensatoren C13 / C20 gehen Sie wie folgt vor: ...
  • Page 3 Technical issues with Jenny Reloaded VFD clock    Please read carefully !  On some Jenny models an issue occured either at once or after some time of operation that the  MosFet T2 runs hot and the clock was not functional anymore. At the same time C13 and / or C20  became discolored and also runs very hot because of an internal short circuit. It was detected that  this ceramic capacitors were taken from a batch, which is unable to withstand the 47 V operating  voltage (the spezification of the capacitors is 50 V) for a longer time.  Please check first, which type of capacitors the clock is equipped as follows:    Disconnect the clock from power  and unscrew out the PCB.   Locate now the positions of C13  and C20 with the help of both left  illustrations and check the type of  the capacitors.      "Good" capacitor          "Bad" capacitor  No modifications          Capacitors C13 and C20  need to be made.          needs to be un‐soldered.    The clock is equipped in total with eight of this 100 nF capacitors; either the "left" or the "right"  version. The possibility of a failure only can happens on C13 and / or C20; which means that the  remaining six "bad" capacitors can be remain soldered in.   ...
  • Page 4 Aufbau- und Montageanleitung IV IV-11/15 -11/15 -11/15 -11/15 -11/15 VFD Uhr „J VFD Uhr „J VFD Uhr „J VFD Uhr „J VFD Uhr „Jenn enny r y reloaded“ eloaded“ eloaded“ eloaded“ eloaded“ Assembly- and Mounting-Instructions IV IV-11/15 -11/15 -11/15 -11/15 -11/15 VFD Cloc VFD Cloc VFD Cloc...
  • Page 5 Aufbau- und Montageanleitung IV IV-11/15 -11/15 -11/15 -11/15 -11/15 VFD Uhr „J VFD Uhr „J VFD Uhr „J VFD Uhr „J VFD Uhr „Jenn enny r y reloaded“ eloaded“ eloaded“ eloaded“ eloaded“ Assembly- and Mounting-Instructions IV IV-11/15 -11/15 -11/15 -11/15 -11/15 VFD Cloc VFD Cloc VFD Cloc...
  • Page 6 Aufbau- und Montageanleitung IV IV-11/15 -11/15 -11/15 -11/15 -11/15 VFD Uhr „J VFD Uhr „J VFD Uhr „J VFD Uhr „J VFD Uhr „Jenn enny r y reloaded“ eloaded“ eloaded“ eloaded“ eloaded“ Assembly- and Mounting-Instructions IV IV-11/15 -11/15 -11/15 -11/15 -11/15 VFD Cloc VFD Cloc VFD Cloc...
  • Page 7 Aufbau- und Montageanleitung IV IV-11/15 -11/15 -11/15 -11/15 -11/15 VFD Uhr „J VFD Uhr „J VFD Uhr „J VFD Uhr „J VFD Uhr „Jenn enny r y reloaded“ eloaded“ eloaded“ eloaded“ eloaded“ Assembly- and Mounting-Instructions IV IV-11/15 -11/15 -11/15 -11/15 -11/15 VFD Cloc VFD Cloc VFD Cloc...
  • Page 8 Aufbau- und Montageanleitung IV IV-11/15 -11/15 -11/15 -11/15 -11/15 VFD Uhr „J VFD Uhr „J VFD Uhr „J VFD Uhr „J VFD Uhr „Jenn enny r y reloaded“ eloaded“ eloaded“ eloaded“ eloaded“ Assembly- and Mounting-Instructions IV IV-11/15 -11/15 -11/15 -11/15 -11/15 VFD Cloc VFD Cloc VFD Cloc...
  • Page 9 BLANK RN5A RN5A RN5B RN5B DOUT RN5C RN5C Title Title Title LED6 RGB LED6 RGB IV-11 VFD-Clock JENNY Reloaded IV-11 VFD-Clock JENNY Reloaded IV-11 VFD-Clock JENNY Reloaded RN6A RN6A Size Size Size Document Number Document Number Document Number RN6B RN6B by.
  • Page 10 Stückliste / Part List IV-11 VFD Clock “Jenny Reloaded” Rev.10/2012 Bauteile / Parts Beschreibung / Description Code St./Qty R5,R15 1k 5% / 1% R3,R7,R17 Widerstände R8,R11,R12,R13 Ax. Induktivität R2,R4,R6,R10,R16 Resistors R9,R14 ax. Inductor 100µH oder Quarz / Crystal L2,L3 or 150µH...