Summary of Contents for Sam SM-2008
- Page 1 SAM ELECTRONIC EQUIPMENT (HK) LIMITED PCB Separator (Moving Type) SM-2008 User’s Manual Address: Room1701,17/F,HenanBuilding, NO.90-92JaffeRoad,Wanchai,HongKong TEL:00852-58042046 FAX：00852-31158812 www.china-sam.com - 1 -...
-
Page 2: Specification
SAM ELECTRONIC EQUIPMENT (HK) LIMITED REV: 01 SM-2008 Machine Dimension 1.Specification Address: Room1701,17/F,HenanBuilding, NO.90-92JaffeRoad,Wanchai,HongKong TEL:00852-58042046 FAX：00852-31158812 www.china-sam.com - 2 -... - Page 3 SAM ELECTRONIC EQUIPMENT (HK) LIMITED ： ： ： ： Applicable PCB length max.360mm PCB Thickness： ： ： ： 〉 〉 〉 〉 0.６ ６ ６ ６ mm(Cutter <0.６ ６ ６ ６ ， ， ， ， >0.3(Cutter Cutting acruracy： ： ： ：...
- Page 4 SAM ELECTRONIC EQUIPMENT (HK) LIMITED Power Supply： ： ： ： 220-230V,50HZ/60HZ Working Temp： ： ： ： 10℃ ℃ ℃ ℃ - - - - 35 35 35 35℃ ℃ ℃ ℃ Humidity Humidity： ： ： ： Humidity Humidity 10%- - - - 85% Weight Weight：...
- Page 5 SAM ELECTRONIC EQUIPMENT (HK) LIMITED 3： ： ： ： Operation and adjustment Instruction 3． ． ． ． 1 Preparation before operating the machine The machine must be securely placed on a bench with suitable height. Clean the cutters with rag to remove the anti-rust oil before use.
- Page 6 SAM ELECTRONIC EQUIPMENT (HK) LIMITED 1. home Length 2. 100mm 200mm Length 300mm Length 5. Speed 400mm Length 7. Emergency 8. Top Cutter 9. Cover Adjustment 10. Dial 11. Adjustment Switch 12. Left-protector 13. Right-protector 14. Bottom Cutter 15. Pre-workholder 16.
- Page 7 SAM ELECTRONIC EQUIPMENT (HK) LIMITED Install foot-switch 1 to No. 8 1.Footswitch 2.Power Supply 3.Motor 4.Top Cutter 5.Bottom Cutter 6.Power wire Connector 7.Safe Precaution 8.Footswitch Connector 3． ． ． ． 4 Power connection 1． ． ． ． Check the power supply for 220V-230V,50Hz-60Hz 2．...
- Page 8 SAM ELECTRONIC EQUIPMENT (HK) LIMITED Check the fuse box and see whether the fuse has been burnt off. Replace a new fuse if necessary. 1． ． ． ． The power socket on the main power supply is used as secondary power supply for the conveyor belt if it is chose as an option.
- Page 9 SAM ELECTRONIC EQUIPMENT (HK) LIMITED 2： ： ： ： Position the foot-switch at a location for easy operation 3． ． ． ． 6． ． ． ． 2： ： ： ： SM-2008 Operating procedures 1： ： ： ： Turn on the power, the light at “0” button starts to blink. Regardless of the top cutter’s position, press “0”...
- Page 10 4． ． ． ． 1： ： ： ： Cutter selection Select cutter according to PCB thickness. There are two types of cutter available in SAM, namely Cutter A and Cutter B. The difference being the cutting angle. Cutter A use for PCB thickness >0.6mm <0.６...