Table of Contents
Advertisement
EN 18
5.
TPM7.1E LA
Table 5-1 SAM mode overview
Main Menu
Sub-menu 1
System Information
Op Hour
Main SW ID
ERR
OP1
OP2
Clear
Press [OK] to clean the Error
Codes immediately
RGB Align
Warm
Normal
Cool
Store
NVM editor
Address
Value
Store
Upload to USB
Copy Channel List to USB
Copy NVM to USB
Copy Readable Info to USB
Copy Edid to USB
Download from USB Copy Channel List from USB
Copy NVM from USB
Copy Readable Info from USB
Copy Edid from USB
Initialize NVM
Press [OK] to Initialize NVM
immediately
EDID Write Enable
Press [OK] to enable EDID
writable immediately
Service Data
Type Number
Production Number
12NC SSB
12NC PSU
12NC Display
Clear OAD Version
Press [OK] to clean OAD
Version immediately
How to Navigate
•
In the SAM menu, select menu items with the UP/DOWN
keys on the remote control transmitter. The selected item
will be indicated. When not all menu items fit on the screen,
use the UP/DOWN keys to display the next/previous menu
items.
•
With the "LEFT/RIGHT" keys, it is possible to:
–
(De) activate the selected menu item.
–
(De) activate the selected sub menu.
–
Change the value of the selected menu item.
•
When you press the MENU button twice while in top level
SAM, the set will switch to the normal user menu (with the
SAM mode still active in the background). To return to the
SAM menu press the MENU button.
•
The "INFO [i+]" key from the user remote will toggle the
OSD "on/off" with "SAM" OSD remaining always "on".
•
Press the following key sequence on the remote control
transmitter: ì062596î directly followed by the MENU button
to switch to SDM (do not allow the display to time out
between entries while keying the sequence). Remarks:
new RC will not have I+ button, but function still remain.
How to Store SAM Settings
To store the settings changed in SAM mode (except the
RGB ALIGN settings), leave the top level SAM menu by using
the POWER button on the remote control transmitter or the
2011-Aug-19
Service Modes, Error Codes, and Fault Finding
Sub-menu 2
e.g. "TPM71E 1.084C"
e.g. "000 000 000 000 000"
e.g. "012 007 208 002 184 032 007 030" Used to read-out the option bytes. See paragraph
e.g. "056 023 000 106 064 000 000 122"
R Gain
G Gain
B Gain
R Gain
G Gain
B Gain
R Gain
G Gain
B Gain
Press [OK] use key pad edit type
number immediately
Press [OK] use key pad edit production
number immediately
Press [OK] use key pad edit SSB
immediately
Press [OK] use key pad edit PSU
immediately
Press [OK] use key pad edit display
immediately
5.2.4
Description
This represents the life timer. The timer counts normal operation hours, but does not count
Stand-by hours.
See paragraph Software Identification, Version, and Cluster for the SW name definition.
Shows all errors detected since the last time the buffer was erased. Five errors possible.
section for a detailed description. Ten codes are possible.
Erases the contents of the error buffer. Select this menu item and press the MENU RIGHT
key on the remote control. The content of the error buffer is cleared.
To align the White Tone. See
paragraph
6.3 Software Alignments
in the Alignments section for a detailed description
Store the RGB value
Select and fill the NVM address
Select and fill the NVM value
Store the value in the address
To upload several settings from the TV to an USB stick
To download several settings from the USB stick to the TV
To initialize a (corrupted) NVM. Be careful, this will erase all settings.
Enable EDID writable
Use Key pad to edit several service data
Clean OAD Version
television set. The mentioned exceptions must be stored
separately via the STORE button.
How to Exit SAM
Use one of the following methods:
•
Switch the set to STANDBY by pressing the mains button
on the remote control transmitter or the television set.
•
Via a standard RC-transmitter, key in "00" sequence.
Note: When the TV is switched "off" by a power interrupt while
in SAM, the TV will show up in "normal operation mode" as
soon as the power is supplied again. The error buffer will not be
cleared.
Customer Service Mode (CSM)
Purpose
The Customer Service Mode shows error codes and
information on the TV's operation settings.The call centre can
instruct the customer (by telephone) to enter CSM in order to
identify the status of the set.This helps the call centre to
diagnose problems and failures in the TV set before making a
service call.
The CSM is a read-only mode; therefore, modifications are not
possible in this mode.
Specifications
•
Ignore "Service unfriendly modes".
6.4 Option Settings
in the Alignments
Hide quick links:
Advertisement
Table of Contents
