Page 4
Eurozone and beyond with a continuous and uninterrupted solution to value and authenticate multi-denomination bundles and separate notes into fit and unfit in one pass. At speeds of up to 1000 notes per minute Nvision offers a convenient and easy cash handling process for customers located anywhere in the world.
This user guide explains the usage and features of all the current configurations of the Nvision. Therefore not all of the features are available on all models. The following annotations will be used for features which are only available on specific models.
Improper work on the electrical components can lead to life threatening injuries from electric shocks! Unprofessional handling or incorrect connections can result in the Nvision no longer being safe for operation. • Electrical work shall be performed only by qualified personnel.
Avoid applying pressure to the detector head, this may damage the head resulting in loss of performance or an inability to function. Contact your local Talaris distributor for further information on how to carry out required operational cleaning. Page 10 of 74 TP05613010 Rev.
Switch on the machine’s on / off switch. The machine will power up and complete a self test routine while the Nvision logo is being displayed. This will take about 20 seconds. At this time the lights on each stacker pocket will flash from red to green.
CURRENCY READY FOR NEW BATCH BACK CANCEL Nvision is capable of supporting multiple currencies depending on the model purchased. If you wish to select an alternative currency, you will have to hold the Currency key down for about 2 seconds.
Function Keys Scroll Keys Total When a currency is selected on Nvision, the machine automatically switches on the counterfeit detection aids relevant to that currency. Turn off BRF to use this process. If you do not wish to authenticate the notes, then you can switch off the authentication by pressing the CDA key.
Re-feed the UNFIT and suspect notes If you have not re-fed the notes within 5 from stacker 2. seconds this display will appear. Press NO to continue the SPLIT. The Nvision will re-show display number 3. € 0 € 0 €...
Start/Stop Note Process Selection Function Keys System Total Clear Detector Batch Nvision can be programmed with personal settings for 5 different users (1 supervisor and 4 operators). USER SETUP OPERATOR 1. CHANGE USER ENTER PASSWORD : _ CLOSE ENTER CLEAR...
These setting include the preferred process, batch sizes, system configuration and detector settings. To save a user settings, configure the Nvision as required, then enter the User Settings function and press Save (F4) A quick way to restore the counter to the users default setting is to enter the user settings option and select LOAD (F2).
Page 57
All Baud rate, parity settings etc. are set internally for that selected printer. For the machine to print, it would need to be connected to a Star TSP-743D printer with a Talaris printer cable which was connected to comm port 2 on the back of the machine.
Function Selection (System) (continued) 5.3.2 Function Selection (System-Version Information) The Version Information can be utilized by the supervisor to help identify the firmware version on each of the main electronic boards of the Nvision. >1. ALL SYSTEM 2. MACHINE MODEL 2.
Smart Batch. The machine will then batch to the size specified for that denomination. NOTE: The Nvision will always batch to the smallest batch size set, therefore the normal batch size should always be equal to or greater then any Smart Batch limit.
Batch” on page 48.) and (see ”5.3.1.14 Printer Port” on page 49.), connect the printer cable to the RS232-2 port on the rear left hand side of the Nvision. Next connect the other end of the printer cable to the Star TSP-743D GRY printer.
Page 70
Printing Totals & BRF Statistics Model: Nvision Nvision Printing Totals & BRF Statistics (continued) BRF statistics can be viewed on the display screen of the machine but can also be printed, if the printer has been attached. (see ”5.3.1.14 Printer Port”...
When connecting the Remote Display to the machine. Please make sure the Nvision is switched off first from the main supply. The Remote display has it’s own power supply as shown in (figure 2).
If the count value exceeds the 8 digits available on the display, two overflow dashes will be shown on both the remote and the Nvision displays. The dashes ‘ - - ’ will be shown on the left hand side of the display followed by the lower 6 digits of the count or on the right side preceded by the upper digits.
Page 84
This document is for general guidance only. Talaris Limited is pleased to give detailed specifications of its products in this document. As the Company's products and services are continually being developed it is important for customers to check that the information contained herein includes the latest particulars. Although every precaution has been taken in preparation of this document, the publisher assumes no responsibility for errors or omissions.