Timer Recording - Philips VR1010/75 User Manual

3
Select Tape Speed
Press ALT/SPEED.
ONE TIME PROGRAM
PROGRAM
CHANNEL+/–
• Each time you press
START +/–
STOP +/–
the button, the tape
REC SPEED LP
DATE +/–
speed alternates bet-
DAILY: 8
ween "SP", "LP", or
CONFIRM: OK
"SLP".
SP, LP : For PAL signal
SP, SLP : For NTSC signal
• To change the stop time, press STOP +/–
(number 2 or 5 button).
4
Confirm Programme
Press OK/STATUS or TIMER.
"PROGRAM WAS COMPLETED"
appears on the TV screen.
After 5 seconds, the above message
disappears, and the normal TV picture
resumes. The (timer) indicator
lights up on the display.
• If "PROGRAM NOT COMPLETED"
appears, try again from step 1.
• If " PROGRAM OVERLAPPED"
appears, the timer recording you just
programmed overlaps another timer
recording. The Program Review screen
will appear with a magenta line blinking.
To change any item on the overlapping
programs, see page 20.
If you want to store other
programmes, repeat steps 1 to 4
5
Finish the Settings
Press POWER to turn off the VCR.
The VCR must be turned off for a timer
recording to take place. If you forget to
turn off the VCR, "PLEASE TURN
OFF VCR FOR TIMER
RECORDING" flashes on your TV
screen two minutes before a timer
recording starts. To remove the
message, press the CLEAR button.
If you want to record the same
programme daily, press DAILY
(Number button 8) at step 3 (Press the
button again to cancel).
The VCR will record a TV programme
every day (Monday through Friday) at
the same time and length. (Daily
Recording)
vr1010/75
If you want to record the same
programme weekly, press WEEKLY
(Number button 9) at step 3 (Press the
1
button again to cancel).
12
08 : 00 PM
The VCR will record a TV programme
10 : 00 PM
once a week at the same day, time, and
14/07/00
FRIDAY
WEEKLY: 9 length. (Weekly Recording)
END: TIMER
If you want to cancel the currently
set programme, press CLEAR.
Note:
• Even if a power failure occurs, the VCR
keeps your timer programs. However, the
clock time and other menu settings are
lost if it lasts for more than 10 minutes.
As a result, when the power is supplied
again to this VCR after the power failure,
set the clock time and turn off the VCR.
Each timer program you have made will
start unless its start time already passes.
— 25 —
25

Timer Recording

To record while you're away, follow step
1 — 9 below. For each programme you
set, the VCR will turn on, start recording,
and turn off automatically. You can store
up to 8 programmes.
Make sure....
• The clock is set to the correct time
before setting timer recording.
• A cassette is inserted in the VCR and
the record tab of the cassette must
not be removed.
• The remote control operation mode
is set correctly for operating your
target component.
– Press VCR to operate the VCR.
– Press TV to operate the TV.
FOR EACH STEP BELOW, YOU
NEED TO FINISH WITHIN 60
SECONDS; OTHERWISE,
PROGRAMMING WILL HAVE TO
BE RESTARTED FROM STEP 1.
1
Select Timer Mode
1 Press VCR.
2 Press TIMER.
G-CODE/SHOWVIEW
QUICK PROGRAMMING
The Timer
PROGRAM REVIEW
Recording menu
SELECT:
appears.
END: TIMER
2
Select Programme mode
5
1 Press PLAY
or
∞
ONE TIME PROGRAM
STOP to select
PROGRAM
CHANNEL+/–
"QUICK PROG-
START +/–
STOP +/–
RAMMING" then REC SPEED SP
DATE +/–
press OK/STAT-
DAILY: 8
CONFIRM: OK
US.
The Quick Programming menu
appears.
• If you have already made 8
programmes, "ALL PROGRAMS IN
USE" appears and goes back to the
Timer Recording menu. If this
happens, delete unwanted programmes.
( P.20)
3
Select Channel
5 ∞
Press CH
or to
ONE TIME PROGRAM
PROGRAM
enter the TV channel.
CHANNEL+/– 12
5
START +/–
• Holding down CH
∞ STOP +/–
REC SPEED SP
or rapidly scans
DATE +/–
through the channels.
DAILY: 8
CONFIRM: OK
• To record from exter-
5
nal line input, press CH or
"A/V REAR" or "A/V FRONT" appears.
00.6.29, 4:54 PM
CONFIRM: OK
1
– –
– –:– – AM
– –:– – AM
– –/– –/– –
WEEKLY: 9
END: TIMER
1
– –:– – AM
– –:– – AM
– –/– –/– –
WEEKLY: 9
END: TIMER
∞
until