National Instruments PCI-8430 Manual

Table of Contents

Quick Links

Table of Contents

Summary of Contents for National Instruments PCI-8430

Page 2 Serial Hardware and Software Help July 2007, 370447J-01 This help file contains instructions to help you install and configure the NI serial hardware and software for Windows 2000/XP/Server 2003/Vista, Windows XP x64/Server 2003 x64/Vista 64, and LabVIEW Real-Time. For more information about this help file, refer to the following topics: Using Help Related Documentation Glossary Important Information Technical Support and Professional Services To comment on National Instruments documentation, refer to the National Instruments Web site. © 2002–2007 National Instruments Corporation. All rights reserved.
Page 3 About this Help File This help file contains instructions to help you install and configure the NI serial hardware and software. This help file includes information about the following serial hardware: PCI-8430 (two, four, eight, and 16 port), PCI-8431 (two, four, and eight port), PCI-8432 (two and four port), and PCI-8433 (two and four port) PCI-232 (two, four, eight, and 16 port), PCI-485 (two, four, and eight port), PCI-232 isolated (two and four port), and PCI-485 isolated (two and four port) PXI-8430 (two, four, eight, and 16 port), PXI-8431 (two, four, and eight port), PXI-8432 (two and four port) and PXI-8433 (two and four port) PXI-8420 (two, four, eight, and 16 port), PXI-8421 (two, four, and eight port), PXI-8422 (two and four port), and PXI-8423 (two and four port) USB-232 (one, two, and four port) and USB-485 (one, two, and four port) ENET-232 (two and four port) and ENET-485 (two and four port) ExpressCard-8420 (two port) and ExpressCard-8421 (two port) PCMCIA-232 (one, two, and four port) and PCMCIA-485 (one and two port) This help file assumes that you are already familiar with Windows and LabVIEW Real-Time.
Page 4: Related Documentation
Related Documentation The following documents contain information that you may find helpful as you use this help file: ANSI/EIA-232-D Standard, Interface Between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary Data Interchange EIA/RS-422-A Standard, Electrical Characteristics of Balanced Voltage Digital Interface Circuits EIA-485 Standard, Standard for Electrical Characteristics of Generators and Receivers for Use in Balanced Digital Multipoint Systems Microsoft Platform Software Developer Kit, Microsoft Corporation NI Serial Hardware Guide NI-VISA Help...
Page 5: Using Help
Using Help Conventions Navigating Help Searching Help Printing Help File Topics...
Page 6 Conventions This help file uses the following formatting and typographical conventions: < > Angle brackets that contain numbers separated by an ellipsis represent a range of values associated with a bit or signal name—for example, AO <0..3>. » The » symbol leads you through nested menu items and dialog box options to a final action. The sequence File»Page Setup»Options directs you to pull down the File menu, select the Page Setup item, and select Options from the last dialog box. This icon denotes a note, which alerts you to important information. This icon denotes a caution, which advises you of precautions to take to avoid injury, data loss, or a system crash. bold Bold text denotes items that you must select or click in the software, such as menu items and dialog box options. Bold text also denotes parameter names. dark red Text in this color denotes a caution. ExpressCard ExpressCard serial boards refers to all versions of the serial boards ExpressCard serial boards. green Underlined text in this color denotes a link to a help topic, help file, or Web address. italic Italic text denotes variables, emphasis, cross references, or an introduction to a key concept. Italic text also denotes text that is a placeholder for a word or value that you must supply. Text in this font denotes text or characters that you should monospace enter from the keyboard, sections of code, programming examples, and syntax examples. This font is also used for the proper names of disk drives, paths, directories, programs, subprograms, subroutines, device names, functions, operations, variables, filenames, and...
Page 7 extensions. Bold text in this font denotes the messages and monospace responses that the computer automatically prints to the bold screen. This font also emphasizes lines of code that are different from the other examples. PCI serial PCI serial boards refers to all versions of the PCI serial boards boards. PCMCIA PCMCIA serial boards refers to all versions of the serial boards PCMCIA serial boards. PXI serial PXI serial boards refers to all versions of the PXI serial boards boards. Serial ENET Serial ENET refers to all versions of the ENET serial boards. USB serial USB serial boards refers to all versions of the USB serial boards boards.
Page 8 Navigating Help (Windows Only) To navigate this help file, use the Contents, Index, and Search tabs to the left of this window or use the following toolbar buttons located above the tabs: Hide—Hides the navigation pane from view. Locate—Locates the currently displayed topic in the Contents tab, allowing you to view related topics. Back—Displays the previously viewed topic. Forward—Displays the topic you viewed before clicking the Back button. Options—Displays a list of commands and viewing options for the help file.
Page 9 Searching Help (Windows Only) Use the Search tab to the left of this window to locate content in this help file. If you want to search for words in a certain order, such as "related documentation," add quotation marks around the search words as shown in the example. Searching for terms on the Search tab allows you to quickly locate specific information and information in topics that are not included on the Contents tab.
Page 10 Wildcards You also can search using asterisk (*) or question mark (?) wildcards. Use the asterisk wildcard to return topics that contain a certain string. For example, a search for "prog*" lists topics that contain the words "program," "programmatically," "progress," and so on. Use the question mark wildcard as a substitute for a single character in a search term. For example, "?ext" lists topics that contain the words "next," "text," and so on.
Page 11 Nested Expressions Use nested expressions to combine searches to further refine a search. You can use Boolean expressions and wildcards in a nested expression. For example, "example AND (program OR VI)" lists topics that contain "example program" or "example VI." You cannot nest expressions more than five levels.
Page 12 Boolean Expressions Click the button to add Boolean expressions to a search. The following Boolean operators are available: AND (default)—Returns topics that contain both search terms. You do not need to specify this operator unless you are using nested expressions. OR—Returns topics that contain either the first or second term. NOT—Returns topics that contain the first term without the second term. NEAR—Returns topics that contain both terms within eight words of each other.
Page 13 Search Options Use the following checkboxes on the Search tab to customize a search: Search previous results—Narrows the results from a search that returned too many topics. You must remove the checkmark from this checkbox to search all topics. Match similar words—Broadens a search to return topics that contain words similar to the search terms. For example, a search for "program" lists topics that include the words "programs," "programming," and so on. Search titles only—Searches only in the titles of topics.
Page 14 Printing Help File Topics (Windows Only) Complete the following steps to print an entire book from the Contents tab: 1. Right-click the book. 2. Select Print from the shortcut menu to display the Print Topics dialog box. 3. Select the Print the selected heading and all subtopics option. Note Select Print the selected topic if you want to print the single topic you have selected in the Contents tab. 4. Click the OK button.
Page 15 Printing PDF Documents This help file may contain links to PDF documents. To print PDF documents, click the print button located on the Adobe Acrobat Viewer toolbar.
Page 16 Introduction The following topics explain how to use this help file, list what you need to get started and optional equipment you can order, and briefly describe the NI serial hardware and software. How to Use this Help File What You Need to Get Started Optional Equipment Serial Hardware Overview PCI Kits PXI Kits USB Kits ENET Kits ExpressCard Kits PCMCIA Kits NI-Serial Software Overview Time-Saving Development Tools...
Page 17 How to Use this Help File To use this help file, refer to the following flow chart and the appropriate topics.
Page 18: What You Need To Get Started
What You Need to Get Started Before you install your serial hardware and the NI-Serial software, make sure you have all of the following items: One of the following hardware kits: PCI Kits PCI-8430 (two, four, eight, or 16 port) PCI-8431 (two, four, or eight port) PCI-8432 (two or four port) PCI-8433 (two or four port) PCI-232 (two, four, eight, or 16 port) PCI-485 (two, four, or eight port) PCI-232 isolated (two or four port) PCI-485 isolated (two or four port) PXI Kits PXI-8430 (two, four, eight, or 16 port) PXI-8431 (two, four, or eight port) PXI-8432 (two or four port) PXI-8433 (two or four port) PXI-8420 (two, four, eight, or 16 port) PXI-8421 (two, four, or eight port) PXI-8422 (two or four port) PXI-8423 (two or four port) USB Kits USB-232 (one, two, or four port) USB-485 (one, two, or four port) ENET Kits ENET-232 (two or four port) ENET-485 (two or four port) ExpressCard Kits ExpressCard-8420 (two port) ExpressCard-8421 (two port)
Page 19 PCMCIA Kits PCMCIA-232 (one, two, or four port) PCMCIA-485 (one or two port) The following CD: NI-Serial Software, which is included in your kit...
Page 20: Optional Equipment
Optional Equipment For more information about ordering the following optional equipment, contact National Instruments: DB-9 RS-485 termination connector (PCI-485, PCI-8431, PCI- 8433, ExpressCard-8421, PCMCIA-485, PXI-8421, PXI-8423, PXI- 8431, PXI-8433, USB-485, and ENET-485 only) 10-position modular jack to DB-9 cable (PCI and PXI four-port boards only) 10-position modular jack to DB-25 cable (PCI and PXI four-port boards only) 68-pin to DB-9 adapter cable (PCI and PXI eight-port and PCI/PXI- 8430/16 boards only) RS-232 9-pin to 9-pin null modem cable RS-232 9-pin to 9-pin straight-through cable RS-232 9-pin to 25-pin null modem cable RS-485 9-pin to 9-pin null modem cable Breakout box (PCI-232/16 and PXI-8420/16 boards only) External power supply (ENET and USB-485/4 only) USB cable (USB two and four port only) One of the following Category 5 twisted-pair network cards (ENET only) Straight-through cable for connecting the serial ENET to a network hub Crossover cable for connecting the serial ENET directly to a computer's network interface card (NIC)
Page 21 Serial Hardware Overview PCI Kits PXI Kits USB Kits ENET Kits ExpressCard Kits PCMCIA Kits...
Page 22 PCI Kits The PCI serial hardware gives you a variety of solutions for serial communication. The RS-232 boards (PCI-8430, PCI-8432, and PCI-232) work with the RS-232 protocol. The RS-485 boards (PCI-8431, PCI-8433, and PCI-485) work with the RS-422 and RS-485 protocols. You can use the RS-232 ports for serial communication up to distances of 50 ft. You can connect the RS-485 ports to up to 31 devices using serial cable lengths up to 4,000 ft. Additionally, the PCI serial boards are available in two-port, four-port, eight-port, and 16-port versions. The two-port versions use DB-9 connectors. The four-port versions use 10-position modular jacks to provide all four connections on a single back panel. Optional cable accessories convert the 10-position modular jacks to either DB-9 or DB- 25 connectors with standard pinouts. The eight-port versions use adapter cables to convert the 68-pin connector on the board to eight DB-9 connectors. The PCI-8430/16 uses two adapter cables to convert the two 68-pin connectors on the board to 16 DB-9 connectors. The PCI-232/16 uses a breakout box to convert the 100-pin connector on the board to 16 DB-9 connectors. Throughout this help file, PCI serial boards refers to all versions of the PCI serial boards. The isolated PCI boards are designed for applications in harsh environments. Isolated ports provide reliable communication in situations involving ground loops from different ground levels or high common mode voltage induced on the lines in noisy environments. Nonisolated ports may not provide reliable communication in those situations. The isolation between each communication port and the host PC ensures the safe operation of the PC and the devices connected to other ports on the same board, in case of accidental high voltages or line surges on communication lines. The RS-232 ports are DTE. In the RS-232 specification, Data Terminal Equipment (DTE) and Data Communications Equipment (DCE) refer to the types of equipment on either end of a serial connection. In general, DTE and DCE refer to computer equipment and modems, respectively. For more information about cabling a RS-232 port to other devices, refer to RS-232 DTE vs. DCE. The RS-485 ports support four hardware transceiver control modes for...
Page 23 Control. All PCI serial hardware uses standard 16550-compatible UARTs (Universal Asynchronous Receiver/Transmitters) for complete compatibility with standard PC COM ports. The serial hardware contains FIFO (First-In-First-Out) buffers to reduce susceptibility to interrupt latency for faster transmission rates. Full Plug and Play compatibility allows switchless configuration and installation. For more information about the serial hardware specifications and operating conditions, refer to the NI Serial Hardware Guide. The following table lists the PCI serial board numbers and corresponding board descriptions. PCI Board Names and Descriptions PCI Board Name Description PCI-8430 RS-232 two port RS-232 four port RS-232 eight port RS-232 16 port PCI-8431 RS-485 two port RS-485 four port RS-485 eight port PCI-8432 RS-232 two port isolated RS-232 four port isolated PCI-8433 RS-485 two port isolated RS-485 four port isolated PCI-232 RS-232 two port RS-232 four port RS-232 eight port RS-232 16 port PCI-485 RS-485 two port RS-485 four port RS-485 eight port...
Page 24 PCI-485I RS-485 two port isolated RS-485 four port isolated...
Page 25 PXI Kits The PXI serial hardware gives you a variety of solutions for serial communication. The RS-232 boards (PXI-8430, PXI-8432, PXI-8420, and PXI-8422) work with the RS-232 protocol. The RS-485 boards (PXI-8431, PXI-8433, PXI-8421, and PXI-8423) work with the RS-422 and RS-485 protocols. You can use the RS-232 ports for serial communication up to distances of 50 ft. You can connect the RS-485 ports to up to 31 devices using serial cable lengths up to 4,000 ft. Additionally, the PXI serial boards are available in two-port, four-port, eight-port, and 16-port versions. The two-port versions use DB-9 connectors. The four-port versions use 10-position modular jacks to provide all four connections on a single front panel. Optional cable accessories convert the 10-position modular jacks to either DB-9 or DB- 25 connectors with standard pinouts. The eight-port versions use adapter cables to convert the 68-pin connector on the board to eight DB-9 connectors. The PXI-8430/16 uses two adapter cables to convert the two 68-pin connectors on the board to 16 DB-9 connectors. The PXI-8420/16 uses a breakout box to convert the 100-pin connector on the board to 16 DB-9 connectors. Throughout this help file, PXI serial boards refers to all versions of the PXI serial boards. The isolated PXI boards are designed for applications in harsh environments. Isolated ports provide reliable communication in situations involving ground loops from different ground levels or high common mode voltage induced on the lines in noisy environments. Nonisolated ports may not provide reliable communication in those situations. The isolation between each communication port and the host PC ensures the safe operation of the PC and the devices connected to other ports on the same board, in case of accidental high voltages or line surges on communication lines. The RS-232 ports are DTE. In the RS-232 specification, Data Terminal Equipment (DTE) and Data Communications Equipment (DCE) refer to the types of equipment on either end of a serial connection. In general, DTE and DCE refer to computer equipment and modems, respectively. For more information about cabling a RS-232 port to other devices, refer to RS-232 DTE vs. DCE. The RS-485 ports support four hardware transceiver control modes for...
Page 26 reliable communication with two and four-wire devices. For more information about transceiver control modes, refer to RS-485 Transceiver Control. All PXI serial hardware uses standard 16550-compatible UARTs (Universal Asynchronous Receiver/Transmitters) for complete compatibility with standard PC COM ports. The serial hardware contains FIFO (First-In-First-Out) buffers to reduce susceptibility to interrupt latency for faster transmission rates. Full Plug and Play compatibility allows switchless configuration and installation. For more information about the serial hardware specifications and operating conditions, refer to the NI Serial Hardware Guide. The following table lists the PXI serial board numbers and corresponding board descriptions. PXI Board Names and Descriptions PXI Board Name Description PXI-8430 RS-232 two port RS-232 four port RS-232 eight port RS-232 16 port PXI-8431 RS-485 two port RS-485 four port RS-485 eight port PXI-8432 RS-232 two port isolated RS-232 four port isolated PXI-8433 RS-485 two port isolated RS-485 four port isolated PXI-8420 RS-232 two port RS-232 four port RS-232 eight port RS-232 16 port PXI-8421 RS-485 two port RS-485 four port RS-485 eight port PXI-8422 RS-232 two port isolated RS-232 four port isolated...
Page 27 PXI-8423 RS-485 two port isolated RS-485 four port isolated...
Page 28 USB Kits The USB serial hardware gives you a variety of solutions for serial communication. The USB-232 hardware works with the RS-232 interface standard, and the USB-485 hardware works with the RS-422 and RS-485 interface standards. You can use the RS-232 ports for serial communication up to distances of 50 ft. You can connect the RS-485 ports to up to 31 devices using serial cable lengths up to 4,000 ft. Additionally, the USB serial hardware is available in one-port, two-port, and four-port versions. All versions use DB-9 connectors. Throughout this help file, USB serial hardware refers to all versions of the USB serial hardware. The USB-232 two and four-port hardware supports three hardware transceiver modes supporting both DTE and DCE configurations. For more information about transceiver control modes, refer to USB-232 Transceiver Modes. The RS-485 hardware supports four hardware transceiver control modes for reliable communication with two and four-wire devices. For more information about transceiver control modes, refer to RS-485 Transceiver Control. In addition, the USB-485 hardware supports programmatic control of the bias resistors. For more information, refer to USB-485 Programmatically Controlled Bias Resistors. All USB serial hardware uses standard 16550-compatible UARTs (Universal Asynchronous Receiver/Transmitters) for complete compatibility with standard PC COM ports. The serial hardware contains FIFO (First-In-First-Out) and USB buffers to reduce susceptibility to system latency for faster transmission rates. Full Plug and Play compatibility allows switchless configuration and installation. For more information about the serial hardware specifications and operating conditions, refer to the NI Serial Hardware Guide.
Page 29 ENET Kits The ENET serial hardware gives you a variety of solutions for serial communication. The RS-232 interfaces work with the RS-232 protocols. The RS-485 interfaces work with the RS-422 and RS-485 protocols. You can use the RS-232 ports for serial communication up to distances of 50 ft. You can connect the RS-485 ports to up to 31 devices using serial cable lengths up to 4,000 ft. The RS-232 ports are DTE. In the RS-232 specification, Data Terminal Equipment (DTE) and Data Communications Equipment (DCE) refer to the types of equipment on either end of a serial connection. In general, DTE and DCE refer to computer equipment and modems, respectively. For more information about cabling a RS-232 port to other devices, refer to RS-232 DTE vs. DCE. The RS-485 boards support four hardware transceiver control modes for reliable communication with two and four-wire devices. For more information about transceiver control modes, refer to RS-485 Transceiver Control. All serial ENET interfaces contain FIFO (First-In-First-Out) buffers to reduce susceptibility to interrupt latency for faster transmission rates. Also, serial ENET interfaces contain additional onboard buffers to reduce susceptibility to Ethernet network traffic. With a serial ENET interface, you gain all the features inherent in a networked device: fewer cabling distance restrictions, device sharing, and communication with devices throughout the Internet. In a serial application, you usually are restricted to the distance limitations of the RS-232, RS-422, or RS-485 specifications. Because the serial ENET interface uses Ethernet, you can add an unlimited distance to your application by exploiting the distances available using a networked device. Device sharing with a serial ENET interface happens on a per- port basis. That is, although the serial ENET interface supports network connections from multiple hosts, each serial port is associated with only one host at a time. Dynamic Host Configuration Protocol (DHCP) is available on many networks to configure network parameters automatically. DHCP simplifies the installation and configuration process for the serial ENET. For more information about DHCP, refer to Using DHCP.
Page 30 If your network does not support DHCP, use the NI Ethernet Device Configuration utility as described in Serial ENET Configuration to configure network parameters for the serial ENET interface.
Page 31 ExpressCard Kits The ExpressCard serial hardware gives you a variety of solutions for serial communication. The ExpressCard-8420 interface works with the RS-232 protocol, and the ExpressCard-8421 interface works with the RS- 422 and RS-485 protocols. You can use the RS-232 ports for serial communication up to distances of 50 ft. You can connect the RS-485 ports to up to 31 devices using serial cable lengths up to 4,000 ft. The ExpressCard-8420 and ExpressCard-8421 are available with two ports. All ExpressCard cards include cables for each port that terminates in a standard DB-9 connector. Throughout this help file, ExpressCard serial interfaces refers to all versions of the interfaces. The RS-232 ports are DTE. In the RS-232 specification, Data Terminal Equipment (DTE) and Data Communications Equipment (DCE) refer to the types of equipment on either end of a serial connection. In general, DTE and DCE refer to computer equipment and modems, respectively. For more information about cabling a RS-232 port to other devices, refer to RS-232 DTE vs. DCE. The RS-485 ports support four hardware transceiver control modes for reliable communication with two and four-wire devices. For more information about transceiver control modes, refer to RS-485 Transceiver Control. All ExpressCard serial hardware uses standard 16550-compatible UARTs (Universal Asynchronous Receiver/Transmitters) for complete compatibility with standard PC COM ports. The serial hardware contains FIFO (First-In-First-Out) buffers to reduce susceptibility to interrupt latency for faster transmission rates. Full Plug and Play compatibility allows switchless configuration and installation. For more information about the serial hardware specifications and operating conditions, refer to the NI Serial Hardware Guide. ExpressCard Board Names and Descriptions ExpressCard Description Board Name ExpressCard-8420 RS-232 two port ExpressCard-8421 RS-485 two port...
Page 32 PCMCIA Kits The PCMCIA serial hardware gives you a variety of solutions for serial communication. The PCMCIA-232 interfaces work with the RS-232 protocol, and the PCMCIA-485 interfaces work with the RS-422 and RS- 485 protocols. You can use the RS-232 ports for serial communication up to distances of 50 ft. You can connect the RS-485 ports to up to 31 devices using serial cable lengths up to 4,000 ft. The PCMCIA-232 is available in one-port, two-port, and four-port versions. The PCMCIA-485 is available in one-port or two-port versions. All PCMCIA cards come with cables for each port that terminates in a standard DB-9 connector. Throughout this help file, PCMCIA serial interfaces refers to all versions of the interfaces. The RS-232 ports are DTE. In the RS-232 specification, Data Terminal Equipment (DTE) and Data Communications Equipment (DCE) refer to the types of equipment on either end of a serial connection. In general, DTE and DCE refer to computer equipment and modems, respectively. For more information about cabling a RS-232 port to other devices, refer to RS-232 DTE vs. DCE. The RS-485 ports support four hardware transceiver control modes for reliable communication with two and four-wire devices. For more information about transceiver control modes, refer to RS-485 Transceiver Control. All PCMCIA serial hardware uses standard 16550-compatible UARTs (Universal Asynchronous Receiver/Transmitters) for complete compatibility with standard PC COM ports. The serial hardware contains FIFO (First-In-First-Out) buffers to reduce susceptibility to interrupt latency for faster transmission rates. Full Plug and Play compatibility allows switchless configuration and installation. For more information about the serial hardware specifications and operating conditions, refer to the NI Serial Hardware Guide.
Page 33 NI-Serial Software Overview The supported interfaces and operating systems are shown in the following table. Supported Interfaces and Operating Systems Windows Windows Hardware Windows Windows 2000/XP/ XP x64/ LabVIEW Interface Vista 32 Vista 64 Server Server Real-Time 2003 2003 x64 ENET ExpressCard PCMCIA Windows Vista, Windows 2000/XP/Server 2003, Windows XP x64/Server 2003 x64, and LabVIEW Real-Time allow a maximum of 256 COM ports. If you require additional ports, contact National Instruments. The NI-Serial software includes the following components: Device driver Measurement & Automation Explorer (MAX) Troubleshooting Wizard (Windows only) Configuration utilities Help files Currently, National Instruments PXI controllers do not offer Windows XP x64 support. NI-VISA support only.
Page 34: Time-Saving Development Tools
Time-Saving Development Tools Your kit includes the NI-Serial software. In addition, you can order LabVIEW or LabWindows™/CVI™ software from National Instruments to speed your application development time and make it easier to communicate with your instruments. LabVIEW is an easy-to-use, graphical programming environment you can use to acquire data from thousands of different instruments, including IEEE 488.2 devices, VXI devices, serial devices, PLCs, and plug-in data acquisition boards. After you have acquired raw data, you can convert it into meaningful results using the powerful data analysis routines in LabVIEW. LabVIEW also comes with hundreds of instrument drivers, which dramatically reduce software development time, because you do not have to spend time programming the low-level control of each instrument. LabWindows/CVI is an interactive ANSI C programming environment designed for building virtual instrument applications. LabWindows/CVI delivers a drag-and-drop editor for building user interfaces, a complete ANSI C environment for building your test program logic, and a collection of automated code generation tools, as well as utilities for building automated test systems, monitoring applications, or laboratory experiments. After you install your serial hardware and the NI-Serial software, you can use NI-VISA in LabVIEW and LabWindows/CVI with your serial interface. If you already have one or more of these applications and want to use them with your serial interface, refer to your product documentation for information about serial I/O functions. For ordering information, contact National Instruments. NI-VISA is a standard I/O application programming interface (API) for instrumentation programming. In its full implementation, NI-VISA can control USB, FireWire, VXI/VME, PXI, GPIB, TCP/IP, or serial instruments, making the appropriate driver calls depending on the type of instrument being used. NI-VISA uses the same operations to communicate with instruments regardless of the interface type. For example, the NI-VISA command to write an ASCII string to a message-based instrument is the same whether the instrument is serial, USB, GPIB, or VXI. As a result, NI-VISA gives you...
Page 35 interface independence. This makes it easier to switch bus interfaces and means that users who must program instruments for multiple interfaces need to learn only one API. Another advantage of NI-VISA is that it is an object-oriented API that will easily adapt to new instrumentation interfaces as they evolve, making application migration to the new interfaces easy. VISA is the industry standard for developing instrument drivers. Most current drivers written by National Instruments use NI-VISA and support Windows, Pocket PC, Linux, Mac OS X, and LabVIEW RT, as long as the appropriate system-level drivers are available for that platform.
Page 36 NI-Serial Software Installation Windows To install the NI-Serial software on your Windows system, follow these steps: 1. Log on as Administrator or as a user with administrator privileges. 2. Insert the NI-Serial Software CD. 3. Click Install Software and follow the onscreen instructions. 4. Install your Windows serial hardware.
Page 37 LabVIEW RT To install the NI-Serial software on your LabVIEW RT target, first follow steps 1–3 in the preceding section to install the software onto the Windows host machine. Then complete the following steps: 1. Launch MAX. 2. Expand Remote Systems by clicking the + next to it. 3. Find your remote system in the list and expand it. 4. Right-click Software and select Add/Remove Software. 5. In the Add/Remove Software window, click NI-Serial and select Install. To use VISA Interactive Control and VISA test panels, you must also install NI-VISA Server. 6. Click Next to start the software download. Click Finish when the download is complete. 7. Shut down your RT controller and install your RT serial hardware.
Page 38: Install The Hardware
Install the Hardware PCI Hardware Installation PXI Hardware Installation USB Hardware Installation ENET Hardware Installation ExpressCard Installation PCMCIA Hardware Installation...
Page 39 PCI Hardware Installation Note If you are installing a PCI RS-485 interface, you might need to adjust the value of the bias resistors, depending on your application. Bias resistors are not available on eight-port PCI hardware. For more information, refer to Bias Resistors. Caution Before you remove your board from the package, touch the antistatic plastic package to a metal part of your system chassis to discharge electrostatic energy, which can damage several components on your serial board. Before installing your hardware, follow the NI-Serial Software Installation instructions. To install your PCI serial board, complete the following steps: 1. Turn off your computer. Keep the computer plugged in so that it remains grounded while you install the PCI serial board. 2. Remove the top or side cover of the computer. 3. Find an unused PCI expansion slot in your computer. 4. Remove the corresponding expansion slot cover on the back panel of the computer. 5. Touch a metal part on your chassis to discharge any static electricity. 6. Insert the PCI serial board into the slot with the serial connectors toward the opening on the back panel. Make sure that you insert the board all the way into the slot. The board might seem to click firmly into place, even though it is only part of the way in. The following figure shows how to install the PCI serial board into an expansion slot.
Page 40 1 PC 2 PCI Serial Board 3 PCI Slot PCI Serial Board Installation 7. Screw the PCI serial board mounting bracket to the back panel mounting rail of the computer. 8. Replace the cover. 9. Turn on your computer. 10. The operating system will automatically detect your hardware. The serial hardware installation is complete. Continue to Verify the Installation.
Page 41 PXI Hardware Installation Note If you are installing a PXI RS-485 interface, you might need to adjust the value of the bias resistors, depending on your application. Bias resistors are not available on eight-port PXI hardware. For more information, refer to Bias Resistors. Caution Before you remove your board from the package, touch the antistatic plastic package to a metal part of your system chassis to discharge electrostatic energy, which can damage several components on your serial board. Before installing your hardware, follow the NI-Serial Software Installation instructions. To install your PXI serial board, complete the following steps: 1. Turn off your PXI or CompactPCI chassis. Keep the chassis plugged in so that it remains grounded while you install the PXI serial board. 2. Find an unused PXI or CompactPCI peripheral slot. 3. Remove the corresponding filler panel. 4. Touch a metal part on your chassis to discharge any static electricity. 5. Insert the PXI serial board into the slot. Use the injector/ejector handle to fully inject the device into place. The following figure shows how to install the PXI serial board into a PXI or CompactPCI chassis.
Page 42 1 Injector/Ejector Handle (In Down Position) 2 PXI Serial Board 3 PXI Chassis 4 Injector/Ejector Rail Installing the PXI Serial Board 6. Screw the PXI serial board front panel to the front panel mounting rail of the PXI or CompactPCI chassis. 7. Turn on your PXI or CompactPCI chassis. 8. The operating system will automatically detect your hardware. The serial hardware installation is complete. Continue to Verify the Installation.
Page 43 USB Hardware Installation Note If you are installing a USB-485/2 or USB-485/4, you might need to adjust the value of the bias resistors, depending on your application. For more information, refer to Bias Resistors. Before installing your hardware, follow the NI-Serial Software Installation instructions. To install your USB serial hardware, complete the following steps: 1. If you are installing a USB-485/4, connect the external power supply. 2. Connect the USB cable from the USB hardware to an available USB port on your computer or USB hub. 3. If your computer is not already on, turn it on. 4. Windows will automatically detect your hardware. The serial hardware installation is complete. Continue to Verify the Installation.
Page 44 ENET Hardware Installation Before installing your hardware, follow the NI-Serial Software Installation instructions. To install your serial ENET hardware, complete the following steps: 1. Connect one end of your Ethernet cable to your serial ENET. (The rear panel of the serial ENET is shown below.) Connect the other end of the Ethernet cable to your Ethernet network. 2. Connect one end of the power cord to the power supply. Screw the power connector on the other end of the power supply onto the power jack of the serial ENET. Plug the other end of the power cord into an AC outlet. Caution If you do not use the power supply included in your kit, ensure that you do not operate your serial ENET interface at any voltage other than the one specified on the rear panel. Doing so could damage the unit. 1 Configuration Reset Switch 2 Power Connection 3 Ethernet Connection 4 Serial Ports 1 and 2 5 Serial Ports 3 and 4 (on 4-Port Models Only) Rear Panel of a Four-Port Serial ENET 3. Refer to the Baseplate Identification Label, shown below, and make a note of the serial number, Ethernet address, and default hostname. Recording this information is not necessary for proper installation. However, you will find it convenient when you...
Page 45 configure the serial ENET. Note The Ethernet address is not the IP address. All devices on an Ethernet network are assigned a unique physical address—the Ethernet address—so they can communicate with each other. Serial Number Ethernet Address Default Hostname Serial ENET Baseplate Identification Label 4. Before you power-on your serial ENET interface, contact your network administrator to determine whether you need to configure your network settings manually using the NI Ethernet Device Configuration utility or use the Dynamic Host Configuration Protocol (DHCP) to perform the configuration automatically. Turn on the front-panel power switch. The PWR/RDY LED alternates rapidly between red and yellow while the unit completes its power-on self-tests and attempts to acquire its network parameters. By default, the serial ENET interface attempts its network configuration through DHCP. The time required for assigning the IP address depends on your network and the configuration of your serial ENET interface. Allow up to 90 seconds and observe the state of the PWR/RDY LED to determine the outcome of the self tests. One of the following should occur: A steady yellow PWR/RDY LED indicates the serial ENET interface passed its self tests and acquired its IP address. The unit is now ready to operate. When using DHCP, the...
Page 46 serial ENET Interface typically is ready to operate about 15 seconds after you power it on. Follow the instructions in Adding a Serial ENET Interface to add the serial ports to your computer. If the PWR/RDY LED continues to alternate rapidly between red and yellow, the unit could not use DHCP to configure its network parameters. Follow the instructions in Adding a Serial ENET Interface to configure the unit properly and add the serial ports to your computer. If the PWR/RDY LED is steady red, the serial ENET has an unrecoverable error. Contact National Instruments Technical Support. If the PWR/RDY LED blinks a slow red/yellow pattern, the serial ENET did not pass its self tests. Refer to ENET PWR/RDY LED Signaling to interpret the flash pattern before calling National Instruments Technical Support. Note If at any time you want to return the serial ENET interface to its default configuration state as given on the baseplate identification label, press and hold the CFG RESET switch for three seconds at power-on. This switch is on the rear panel, as shown in the figure above. Refer to Using the CFG RESET Switch for more information.
Page 47 ExpressCard Hardware Installation Before installing your hardware, follow the NI-Serial Software Installation instructions. To install the ExpressCard serial board in your computer, insert the card into a free ExpressCard socket. The card has no jumpers or switches to set, and you do not need to shut down the system before you insert it. Windows will automatically detect your hardware. The serial hardware installation is complete. Continue to Verify the Installation.
Page 48 PCMCIA Hardware Installation Before installing your hardware, follow the NI-Serial Software Installation instructions. To install the PCMCIA serial board in your computer, insert the card into a free PC Card (PCMCIA) socket. The card has no jumpers or switches to set, and you do not need to shut down the system before you insert it. The following figure shows how to insert a PCMCIA serial card and how to connect the cable. 1 PCMCIA Socket 2 PCMCIA Serial Cable Inserting a PCMCIA Serial Card Windows will automatically detect your hardware. The serial hardware installation is complete. Continue to Verify the Installation.
Page 49 Measurement & Automation Explorer (MAX) Overview Launching MAX Adding a Serial ENET Interface Verify Installation and Troubleshoot NI-Serial Problems Delete a Serial Interface View NI-Serial Software Version Monitor, Record, and Display NI-VISA API Calls System Report Generation View or Change Serial Port Settings Port Settings Advanced Settings Save Pending Changes Discard Pending Changes Restore Defaults Import/Export a Configuration File NI-Serial Communicator Recover Unused COM Numbers Additional Help and Resources NI-Serial Online Help National Instruments Serial Web Site...
Page 50 MAX Overview You can perform the following serial-related tasks in MAX: Establish basic communication with your serial devices. Launch the NI-Serial Troubleshooting Wizard to verify installation and troubleshoot serial problems. (Windows only.) Launch NI Spy to monitor NI-VISA API calls to serial interfaces. (Windows only.) View information about your serial hardware and NI-Serial software. Reconfigure the serial interface settings. Locate additional help resources for NI-Serial.
Page 51 Launching MAX To start MAX, double-click the MAX icon on the desk or select Start»Programs»National Instruments»Measurement & Automation. On Windows Vista, to make changes to serial port settings, you must launch MAX with administrative privileges. To launch MAX with administrative privileges, right-click the MAX icon on the desktop or the Start menu and select Run as administrator. You must enter an administrative password if you are not an administrator. When you launch MAX, the following window appears: Measurement & Automation Explorer...
Page 52 Adding a Serial ENET Interface LabVIEW RT users do not need to add serial ENET interfaces to their RT controllers. To use a serial ENET interface on your LabVIEW RT system, you simply configure it. Refer to Viewing Network Settings for instructions on viewing and configuring network settings for serial ENET interfaces. To add a serial ENET interface on your Windows system, complete the following steps: 1. Launch MAX. 2. Right-click Devices and Interfaces and select Create New..3. In the Create New... dialog window, select Serial ENET Interface and click Finish. 4. Follow the prompts in the Add Serial ENET Hardware Wizard to add your serial ENET interface. If the PWR/RDY LED continues to alternate rapidly between red and yellow, the unit could not use DHCP to configure its network parameters. You need to use the NI Ethernet Device Configuration utility to configure your serial ENET interface. Refer to Configuring Network Settings for more information. 5. When finished, select Restart Now to finish the serial ENET installation. After the computer has finished restarting, continue to Verify the Installation.
Page 53 Verify Installation and Troubleshoot NI-Serial Problems The NI-Serial Troubleshooting Wizard supports ports only on your local Windows system. It does not test your LabVIEW Real-Time serial ports. To verify the hardware and software installation and troubleshoot NI- Serial problems, follow these steps to run the Troubleshooting Wizard: 1. Launch MAX. 2. Select Help»Troubleshooting»NI-Serial Troubleshooting Wizard. The Troubleshooting Wizard tests your serial interface and displays the results as shown below. NI-Serial Troubleshooting Wizard The Troubleshooting Wizard verifies that your serial driver is installed properly, that the configuration of your hardware does not conflict with anything else in your system, and that the serial driver can communicate with your hardware correctly. To view online help for the Troubleshooting Wizard, click the Help button.
Page 54 Delete a Serial Interface Before you physically remove a serial interface from your Windows system, follow these steps to remove the hardware information: 1. Launch MAX. 2. Expand the Devices and Interfaces directory by clicking the + next to the folder. 3. Right-click on your serial interface and select Delete from the drop-down menu that appears. 4. When prompted, click the Yes button to confirm the removal of your interface. 5. MAX automatically updates the list of installed serial interfaces. You can also select View»Refresh to update the list. On LabVIEW RT, it is not necessary to programmatically delete hardware from the system. Simply power down your RT controller and remove the hardware. When you power on your RT controller again, the ports are automatically removed from the system. You may need to refresh MAX to see the changes.
Page 55 View NI-Serial Software Version To view the NI-Serial software version for Windows, follow these steps: 1. Launch MAX. 2. Expand the Software directory by clicking the + next to the folder. 3. Click NI-Serial. MAX displays the NI-Serial software version number in the right pane. To view the NI-Serial software version installed on a LabVIEW RT controller, follow these steps: 1. Launch MAX. 2. Expand Remote Systems by clicking the + next to it. 3. Find your RT controller in the list and expand it. 4. Expand the Software directory. 5. Click NI-Serial. MAX displays the NI-Serial software version number in the right pane.
Page 56 Monitor, Record, and Display NI-VISA API Calls NI-Spy is available only on Windows. To monitor NI-VISA calls, use NI Spy as follows: 1. Launch MAX. 2. Expand the Devices and Interfaces directory by clicking the + next to the folder. 3. Right-click on your serial interface and select NI Spy from the drop-down menu that appears. 4. On the NI Spy toolbar, click the blue arrow button to start a capture. 5. Start the NI-VISA application you want to monitor. NI Spy records and displays all NI-VISA calls, as shown below. For more information about using NI Spy, select Help»Help Topics in NI Spy.
Page 57 System Report Generation You can use the Report Generation feature in MAX to create a snapshot of the National Instruments hardware and software installed on your system. To create a report, follow these steps: 1. Launch MAX. 2. Click File»Create Report..3. Follow the dialog prompts to select the report type and the system and components you want to include in the report. 4. Select a report filename and location. Click the View report after the wizard exits box to launch the report automatically.
Page 58 View or Change Serial Port Settings To view or change your Windows serial port settings, follow these steps: 1. Launch MAX. 2. Expand the Devices and Interfaces directory by clicking the + next to the folder. 3. Select your serial interface to display hardware information in the right pane. 4. Right-click on the serial port you want to modify and select Goto COM#, where # is the serial COM number assigned to that physical port. This directs you to the appropriate serial port under the Serial & Parallel section of MAX. To view or change your LabVIEW RT port settings, follow these steps: 1. Launch MAX.
Page 59 2. Expand Remote Systems by clicking the + next to the folder. 3. Find your RT controller in the list and expand it. 4. Expand the Devices and Interfaces directory. 5. Expand the Serial entry. 6. Built-in ports and plug-in boards are displayed. To change the settings of a port on a plug-in serial board, select it from the list and expand it to see the ports. 7. Select a port to change its settings. To see chassis and slot information for plug-in serial boards, identify your PXI system. To view or change the port settings, click the Port Settings tab. For more information about these settings, refer to Port Settings.
Page 60 To change the transceiver mode, enable or disable the FIFOs, or enable or disable the bias resistors on the USB-485, click the Advanced tab. For more information about these settings, refer to Advanced Settings. Note Transceiver modes apply to RS-485 and USB-232 (two and four port) interfaces only. For more information about transceiver modes, refer to Using Your Serial Hardware.
Page 61: Port Settings
Port Settings In the Port Settings tab, you can change any setting by clicking the arrow button to the right of a field. When you click the arrow button, a list of valid values for that field appears, and you can select the desired setting from the list. The following figure shows the Port Settings tab.
Page 62: Advanced Settings
Advanced Settings To view or change the advanced settings, click the Advanced tab, shown in the following figure. The available settings may change depending on what serial interface you are configuring. Click Show Help in the upper right corner of the MAX window for information about specific advanced settings.
Page 63 Save Pending Changes To save your changes to this item, click Save.
Page 64 Discard Pending Changes To discard your changes to this item, click Revert. Revert is available only if you have made at least one change to this item. It undoes any changes you have made and restores the item to the most recently saved state.
Page 65: Restore Defaults
Restore Defaults To reset the fields to their default values at any time, click the Defaults button.
Page 66: Import/Export A Configuration File
Import/Export a Configuration File Import/export is available only for your LabVIEW Real-Time serial ports. You can export your port settings to a file and use that file later to import those settings back into a LabVIEW Real-Time system. You can use this method to back up and restore your port settings or deploy them to other systems. To export your port settings to a file, select File»Export. Be sure to pick the correct LabVIEW Real-Time system from which to export. To import settings from a file to your ports, select File»Import. Be sure to pick the correct LabVIEW Real-Time system to which to import. For more information, refer to Measurement & Automation Explorer Help. To access this help, select Help»MAX Help.
Page 67 NI-Serial Communicator The NI-Serial Communicator is a utility that allows you to establish basic communication with your instrument or another serial port. The NI-Serial Communicator is available only for Windows serial ports. Follow these steps to launch the NI-Serial Communicator: 1. Launch MAX. 2. Expand the Devices and Interfaces directory by clicking the + next to the folder. 3. Select your serial interface and expand it to see its ports by clicking the + next to its name. 4. Right-click on the serial port you want to use and select Communicate with Instrument. This launches the NI-Serial Communicator. You can use the General, Flow Control, and Advanced tabs to change the port settings. Use the Test tab to write and read strings through the COM port.
Page 68 Recover Unused COM Numbers When serial hardware is physically removed from a Windows system without first being deleted from the operating system, Windows continues to mark the COM numbers associated with that hardware as "in use." This allows you to reinsert the hardware and have those ports keep their original COM numbers. To free up the COM number assignments that are no longer associated with hardware physically present in the system, follow these steps: 1. Launch MAX. 2. Select Tools»NI-Serial»Recover Unused COM Numbers.
Page 69: Additional Help And Resources
Additional Help and Resources To access additional help and resources for the NI-Serial software and your serial hardware, refer to the following topics. NI-Serial Online Help National Instruments Serial Web Site...
Page 70 NI-Serial Online Help The NI-Serial Help addresses questions you might have about NI-Serial and includes troubleshooting information. Follow these steps to access the NI-Serial online help: 1. Launch MAX. 2. Select Help»Help Topics»NI-Serial.
Page 71 National Instruments Serial Web Site Follow these steps to access the National Instruments Web site for serial: 1. Launch MAX. 2. Select Help»National Instruments on the Web»NI-Serial.
Page 72 Serial ENET Configuration Viewing Network Settings Configuring Network Settings Using the CFG RESET Switch Verifying the Hostname Using DHCP Using Static IP Parameters Updating Firmware...
Page 73: Viewing Network Settings
Viewing Network Settings To view network settings for a serial ENET interface, complete the following steps: 1. Launch MAX. 2. Select Tools»NI-Serial»Ethernet Device Configuration. NI Ethernet Device Configuration Utility 3. The NI Ethernet Device Configuration utility displays a list of devices found on your subnet, sorted by model. You can identify your device by the Ethernet address or the serial number found on the baseplate label. The listed devices can be in one of four possible states, as indicated in the IP address/hostname column: A hostname indicates DHCP has successfully configured the device. A numerical IP address indicates the device has successfully been configured with a static IP address. *Unconfigured* indicates the device is configured to use DHCP, but DHCP failed to attain network parameters. *Busy* indicates the device is configured to use DHCP and currently is attempting to acquire network parameters. 4. The NI Ethernet Device Configuration utility automatically verifies that the hostname for each DHCP-enabled device matches the DNS entry for the assigned IP address. This verification process automatically occurs when you either run the utility or click...
Page 74 Refresh. The utility alerts you as shown below if it detects a problem with the network settings. Hostname Verification Error Detected 5. To view or change the settings for a particular serial ENET interface, select it in the list and click Properties. Refer to Configuring Network Settings for information about configuring your serial ENET network settings.
Page 75: Configuring Network Settings
Configuring Network Settings Your serial ENET interface must be in network configuration mode if you want to change its network settings. Any changes you make while in normal operating mode will not take effect. If the serial ENET interface is configured to use DHCP, and DHCP is unavailable, the unit automatically enters network configuration mode after a 60 second timeout. The unit must be in this mode before you can make changes to the network parameters. You also can enter this mode during normal operation by pressing and holding the CFG RESET switch for three seconds. Refer to Using the CFG RESET Switch for more information about using this switch. While in network configuration mode, the PWR/RDY LED alternates rapidly between red and yellow, and normal operation is halted. Note If you only want to view the network configuration settings without making changes, you do not need to place the unit into network configuration mode. While in normal operation, you can follow the instructions below to examine the properties for any National Instruments Ethernet device on your subnet. However, any changes you attempt to make to the network parameters while in normal operating mode will not take effect. To configure network settings, complete the following steps: 1. When you select Properties... from the NI Ethernet Device Configuration utility, the utility displays the properties for your serial ENET interface, similar to the following example.
Page 76 Properties Window for an Unconfigured Serial ENET Interface The current hostname is displayed. The hostname associates a name with a numerical IP address. Hostname is a required field. The serial ENET interface attempts to use the hostname when registering with DHCP. Many DHCP servers can register the hostname and assigned IP address. You then can reliably use the hostname to communicate with your serial ENET interface even if the numerical IP address changes. However, some DHCP servers do not implement hostname registration. The serial ENET interface requires domain name server (DNS) registration when using DHCP. If your DHCP server does not support DNS registration, you must use static network parameters. Consult your network administrator for more details. For more information about DHCP, refer to Using DHCP. 2. In the Properties window, select either Obtain an IP address automatically (DHCP) or Use the following IP settings. 3. If you select Obtain an IP address automatically (DHCP), you do not need to enter any network parameters unless you want to...
Page 77 change the hostname of the Ethernet device. If you select Use the following IP settings, enter the network parameters you have chosen for the host IP address, subnet mask, gateway IP, and DNS server IP, as in the example shown below. Refer to Using Static IP Parameters for more information. Specifying IP Settings Note The IP settings shown above are shown only as a format example. 4. You can enter an optional comment to help you identify the device. 5. Click OK to configure the device, or Cancel to exit without saving the configuration changes. 6. Click Exit (or Cancel) to close the NI Ethernet Device Configuration utility. The device automatically reboots with the new configuration in effect.
Page 78: Using The Cfg Reset Switch
Using the CFG RESET Switch The Configuration Reset (CFG RESET) switch is a recessed switch beside the Ethernet (ENET) connector on the rear panel. Refer to Rear Panel of a Four-Port Serial ENET Interface for an illustration of its location. This switch performs two functions, depending on whether you press it at power-on or during operation.
Page 79 Using the CFG RESET Switch during Operation While the serial ENET interface is operational, as indicated by a steady yellow PWR/RDY LED, you can use the CFG RESET switch to place the box into network configuration mode. This special mode ensures that network parameters are not changed while in normal operation mode. Because you cannot change the network parameters unless you deliberately place the serial ENET interface into network configuration mode, the parameters are protected while in normal operation. Hosts cannot connect to the serial ENET interface while it is in network configuration mode. Note Pressing the CFG RESET switch has no effect if hosts are currently connected. Close all connections, then press and hold the CFG RESET switch and wait approximately three seconds until the PWR/RDY LED becomes solid red. If you release the switch prior to three seconds, the serial ENET interface continues to operate normally. The PWR/RDY LED goes through the following changes during these three seconds: 1. The LED begins slowly alternating between red and yellow. 2. The alternating pattern increases in tempo. 3. At three seconds, the PWR/RDY LED becomes steady red. This indicates the serial ENET interface is ready to enter network configuration mode. 4. Now release the CFG RESET switch. The PWR/RDY LED alternates rapidly between red and yellow to indicate the serial ENET interface is now in network configuration mode. This mode remains in effect until you switch off the serial ENET interface or you use the NI Ethernet Device Configuration utility to change its network characteristics.
Page 80 Using the CFG RESET Switch at Power-On In the event you forget the network configuration that a particular serial ENET interface is using, you can reset the unit to its default network characteristics. By pressing and holding the CFG RESET switch while you power on the serial ENET interface, the network parameters revert to the default settings as defined on the baseplate label. You must press and hold the switch for approximately three seconds until the PWR/RDY LED becomes solid red. If you release the switch prior to three seconds, no change occurs to the network configuration, and the serial ENET interface continues to boot normally. The PWR/RDY LED goes through the following changes during these three seconds: 1. The LED begins slowly alternating between red and yellow. 2. The alternating pattern increases in tempo. 3. At three seconds, the PWR/RDY LED becomes steady red. This indicates the network configuration will be set to the factory default settings. 4. When you release the CFG RESET switch, the box continues to boot as normal, and the PWR/RDY LED indicates the boot process as described in ENET LED Descriptions.
Page 81: Verifying The Hostname
Verifying the Hostname To correct a problem with the hostname, complete the following steps: 1. Locate the device that has a problem. This is indicated by an (!) on the device icon, as shown in the NI Ethernet Device Configuration utility. 2. Select Properties..A dialog box similar to the following appears. Resolving a Hostname Verification Error 3. The utility gives you four options for resolving the verification error. Select the one that best fits your situation and click OK. Change the device's hostname to match the DNS entry. Use this option if you want to accept the hostname the DHCP server assigns, or if you cannot contact the network administrator to change the DNS entry. Use static network parameters instead of DHCP. Use this option if you cannot use the hostname the DHCP server assigns. Contact your network administrator to obtain a valid IP address, subnet, and gateway. This option disables DHCP on the device. Edit the current hostname. Use this option to change the hostname to a name other than either the configured hostname or the name the DHCP server assigns. Contact your network administrator to obtain a valid name.
Page 82 Keep the existing hostname. Use this option to keep the previously assigned hostname. If you select this option, contact your network administrator to change the DNS entry. 4. Review the network parameter settings in the Properties window. 5. Confirm that the device is in network configuration mode and click OK. The device reboots with the new settings in effect. 6. After the device reboots, click Refresh to verify that the hostname is now valid.
Page 83: Using Dhcp
Using DHCP The Dynamic Host Configuration Protocol (DHCP) is designed for large networks in which networking devices are transient and network parameters cannot be statically assigned and thus tied to specific devices. DHCP eases the addition of networking devices onto a network by having a server assign necessary network parameters, including the IP address, netmask, and router information, to a newly attached network device. Optionally, if the device provides a hostname with the configuration request, DHCP may attempt to configure your network to recognize the device with the requested hostname. DHCP requires a Domain Name Server (DNS) to associate the numerical IP address assigned with the requested hostname. Within the past few years, an Internet community standard has emerged to provide a standardized way for these services to provide dynamic domain name services. Using this standard, after DHCP assigns the numerical IP address, it can communicate with DNS to register the newly assigned IP address with the requested hostname. However, the complexity of DHCP and dynamic name registration typically requires active management by a corporate MIS department, or equivalent, because of several risks for failure. One possible failure can occur if the pool of available addresses contains no more unassigned IP addresses. This problem is evident if DHCP fails to work and the PWR/RDY LED continues to flicker for longer than 90 seconds at power on. In this situation, you need to obtain a static IP address from your network administrator and configure the device yourself using the NI Ethernet Device Configuration utility. Notice that if DHCP fails to assign you an address, the current subnet might not have an address available for you to use. In this case, you may need to move your product to another subnet where there is an available IP address. Failure also happens if communication between DHCP and DNS does not occur. In this situation, DHCP assigns an address to the device, but you cannot communicate to it using the hostname you assigned. Your network administrator may need to insert the hostname manually into the DNS table. Alternately, you can use the NI Ethernet Device Configuration utility to determine the hostname associated with your assigned IP address, and change the hostname to match the DNS entry. Refer to Verifying the Hostname for more information.
Page 84 Because there are many other possible reasons for failure, contact your network administrator if you are having problems getting DHCP to work. When you can use DHCP and DNS successfully, you can use the hostname form of the IP address to communicate with your product— even if the numerical IP address changes with successive reboots. If you are setting up a small network for your instrumentation system, National Instruments recommends using static IP addresses, because they are easier to implement and maintain. In this system, you can safely use the numerical form of the IP address to communicate with your product because the address is unlikely to change. Small networks are less likely to have domain name services available that would resolve the hostname into a numerical IP address.
Page 85 Using Static IP Parameters If DHCP is not available, you must provide the serial ENET interface with several important network parameters. These parameters are listed below. IP address—The unique, computer-readable address of a device on your network. An IP address typically is represented as four decimal numbers separated by periods (for example, 130.164.54.20). Refer to Choosing a Static IP Address. Subnet mask—A code that helps the network device determine whether another device is on the same network or a different network. Gateway IP—The IP address of a device that acts as a gateway, which is a connection between two networks. If your network does not have a gateway, set this parameter to 0.0.0.0. DNS Server—The IP address of a network device that stores hostnames and translates them into IP addresses. If your network does not have a DNS server, set this parameter to 0.0.0.0.
Page 86 Choosing a Static IP Address For a Network Administered by a Network Administrator If you are adding the serial ENET interface to an existing Ethernet network, you must choose IP addresses carefully. Contact your network administrator to obtain an appropriate static IP address for your serial ENET interface. Also, have the network administrator assign the proper subnet mask, gateway, and DNS server addresses. For a Network without a Network Administrator If you are assembling your own small Ethernet network, you can choose your own IP addresses. The subnet mask determines the IP address format. You should use the same subnet mask as the computer you are using to configure your serial ENET interface. If your subnet mask is 255.255.255.0, the first three numbers in every IP address on the network must be the same. If your subnet mask is 255.255.0.0, only the first two numbers in the IP addresses on the network must match. For either subnet mask, numbers between 1 and 254 are valid choices for the last number of the IP address. Numbers between 0 and 255 are valid for the third number of the IP address, but this number must be the same as other devices on your network if your subnet mask is 255.255.255.0. If you are setting up your own network, you probably do not have a gateway or DNS server, so you should set these values to 0.0.0.0.
Page 87: Updating Firmware
Updating Firmware The NI-Serial software contains a firmware update utility you can use to access new features that may be added to the serial ENET interface in the future. It may be necessary to update the firmware to take advantage of these new features. You need to know either the IP address or hostname of your serial ENET interface before you run the NI Ethernet Device Firmware Update utility. If you do not remember this information, you can obtain it by Viewing Network Settings. Note The NI Ethernet Device Firmware Update utility cannot update the firmware while any network connections are active. Close any open connections before you attempt a firmware update. Hosts cannot connect to the serial ENET interface while it is updating the firmware. Complete the following steps to run the NI Ethernet Device Firmware Update utility. 1. Launch MAX. 2. Expand the Devices and Interfaces directory by clicking on the + next to the folder. 3. Right-click any serial ENET interface and select Update Firmware. NI Ethernet Device Firmware Update Utility...
Page 88 4. Enter the IP address or the hostname of the serial ENET interface in the IP address or hostname edit box. An example of an IP address is 137.65.220.40. An example of a hostname is nienetB9B76A. 5. Enter the full path of the binary file where the firmware is located in the EEPROM binary image filename edit box. You also can click Browse... to locate the file. 6. Click Update to update the firmware. The NI Ethernet Device Firmware Update utility communicates with the specified serial ENET interface to verify the box has no open network connections and determine the current version of the firmware in the unit. A dialog box reports that the update utility is searching for the Ethernet device. 7. The utility prompts you to confirm the change you are about to perform. Click OK to continue. As the update utility transfers the firmware image to your serial ENET interface, the Update Progress status bar fills, and the Current status box describes each step in the process. The Current status box reports whether the firmware update completed successfully or failed. The serial ENET interface automatically reboots with the new firmware in effect. Caution Do not power-off the serial ENET interface or disconnect the power supply while running the NI Ethernet Device Firmware Update utility. Doing so will damage the unit. 8. Click Exit to close the NI Ethernet Device Firmware Update utility.
Page 89 Using Your Serial Hardware The following topics describe how to use the advanced features of your NI serial hardware and list some general programming requirements. General Programming Requirements Baud Rates Performance on LabVIEW Real-Time Advanced Features FIFO Buffers Retrieving the Serial Interface Type RS-485 Transceiver Control Setting the RS-485 Transceiver Control Mode in Windows Setting the RS-485 Transceiver Control Mode in LabVIEW RT Bias Resistors USB-485 Programmatically Controlled Bias Resistors Setting the USB-485 Programmatically Controlled Bias Resistor Mode Retrieving the RS-232 Transceiver State with DeviceIoControl USB-232 Transceiver Control Setting the RS-232 Transceiver Mode with DeviceIoControl Setting Ring Indicate and Data Carrier Detect (DCD) with DeviceIoControl Status LEDs USB LED Descriptions ENET LED Descriptions ENET PWR/RDY LED Signaling...
Page 90 General Programming Requirements The NI-Serial software for Windows is fully integrated into the standard Windows communications software. NI serial ports are used like any other Windows communications (COM) port. Windows has standard communication functions for use within Windows applications. When you develop your application, remember that you must use the standard Windows serial communication functions or any API that uses the standard Windows serial communication functions such as NI-VISA. For more information about NI-VISA, see ni.com/VISA. For information about Microsoft Windows serial communication functions, refer to the Platform Software Development Kit. If you have LabVIEW, LabWindows/CVI, or VISA and want to use it with your serial hardware, refer to your LabVIEW, LabWindows/CVI, or VISA documentation for information about serial I/O functions.
Page 91: Baud Rates
Baud Rates The maximum baud rates supported are listed in the table below. Maximum Baud Rate Hardware Platform RS-232 RS-485 PCI-843x 1000 kbit/s 3000 kbit/s PCI-232/485 115.2 kbit/s 460.8 kbit/s PXI-843x 1000 kbit/s 3000 kbit/s PXI-842x 115.2 kbit/s 460.8 kbit/s 230.4 kbit/s 460.8 kbit/s ENET 230.4 kbit/s 460.8 kbit/s ExpressCard 230.4 kbit/s 460.8 kbit/s PCMCIA 921.6 kbit/s 921.6 kbit/s All NI serial hardware supports standard baud rates. In addition, the PCI/PXI-843x family of hardware supports any baud rate between 2 bit/s and the maximum supported baud rate for that interface. National Instruments considers the following baud rates to be standard. NI serial hardware supports these rates up to the maximum rate specified. Your device may also support additional baud rates not listed below: 14400 19200 38400 1200 57600 2400 115200 4800 230400...
Page 92 The two-wire auto control mode for the RS-485 transceiver has a maximum baud rate of 2000 kbit/s. The PCMCIA-232/4 has a maximum baud rate of 115.2 kbit/s.
Page 93 Performance on LabVIEW Real-Time NI-Serial users on LabVIEW Real-Time have control over whether secondary interrupt handling is enabled. When secondary interrupt handling is enabled, I/O is processed at a priority lower than time-critical. Using secondary interrupt handling reduces jitter for time-critical loops and makes serial hardware interrupts more deterministic. However, it may also reduce I/O performance and can increase the possibility of overflowing the RX FIFO buffer. Secondary interrupt handling is a setting at the system-wide level and is enabled by default. To enable or disable this feature, complete the following steps: 1. Copy to your host the niserial.dbs file in the /ni-rt/system directory on the RT target. 2. In the niserial.dbs file, find the entry SecondaryInterrupts and modify it accordingly: To enable secondary interrupt handling, set SecondaryInterrupts to 1. To disable secondary interrupt handling, set SecondaryInterrupts to 0. 3. Download the updated niserial.dbs file to the target, overwriting the existing file in the /ni-rt/system directory. 4. Reboot your RT target.
Page 94: Advanced Features
Advanced Features In addition to supporting standard 16550-compatible UART functionality, some NI serial hardware supports additional advanced features: Adjustable FIFO levels RS-485 transceiver control RS-485 socketed bias resistors RS-485 programmatically controlled bias resistors RS-232 transceiver state RS-232 DTE/DCE transceiver control To determine which features your product supports, refer to the following table. Serial Hardware Features RS-485 RS-485 Adjustable RS-485 Socketed Programmatically Hardware FIFO Interface Transceiver Bias Controlled Bias Settings Type Control Resistors Resistors PCI/PXI- 8430, PCI/PXI-8432 PCI-232, PXI-8420, PXI-8422 PCI/PXI-8431 eight port, PCI-485 eight port, PXI- 8421 eight port All other PCI/PXI-...
Page 95 8421, and PXI-8423 USB-232 one port USB-232 two and four port USB-485 one port USB-485 two and four port ENET-232 ENET-485 ExpressCard- 8420 ExpressCard- 8421 PCMCIA-232 PCMCIA-485...
Page 96: Fifo Buffers
FIFO Buffers FIFO buffers are present on the 16550-compatible UARTs—one for the transmitter and one for the receiver. The Receive Buffer control sets the number of characters received in the FIFO before the PC is interrupted to read the data. The Transmit Buffer control sets the maximum number of bytes written to the FIFO in a block when the PC is interrupted to write the data. The built-in ports on PXI RT controllers and the PCI, PXI, and PCMCIA plug-in serial boards have configurable FIFO settings. Use the Advanced tab in MAX to configure your FIFO settings. When you configure FIFO settings, consider the following points: You can select larger FIFO buffer sizes to reduce the number of interrupts your PC receives and thereby minimize system overhead. If transfer rates are high, you can lower the Receive Buffer value to prevent overrun errors due to interrupt latency. If your data transfer sizes are small, and your Receive Buffer value is above your data sizes, your system is less efficient. For maximum efficiency, set your Receive Buffer value such that your data transfer size is a multiple of that value.
Page 97 Retrieving the Serial Interface Type (RS-232 or RS-485) There are two ways to retrieve the serial interface type (RS-232 or RS- 485): Read the NI-VISA wire mode attribute. The NI-Serial software uses programmatic control codes and the DeviceIoControl Windows function to retrieve the serial interface type. To retrieve the serial interface type using the DeviceIoControl Windows function, complete the following steps: 1. Add the following lines to your source code: #include <winioctl.h> #include <NiSerial.h> Note The header file NiSerial.h is included on your NI- Serial software CD. You also can find it in the NI-Serial folder where you installed your National Instruments software (typically, C:\Program Files\National Instruments\NI- Serial). 2. The SERIAL_INTERFACE attribute can have the following values: RS485_INTERFACE RS232_INTERFACE 3. To retrieve the serial interface type, use NISERIAL_GET_INTERFACE_TYPE and DeviceIoControl with the following code: SERIAL_INTERFACE l_SerialInterface; DWORD l_ByteCount; DeviceIoControl ( PortHandle, NISERIAL_GET_INTERFACE_TYPE, (LPVOID) NULL,...
Page 98 0, (LPVOID) &l_SerialInterface, sizeof (l_SerialInterface), (LPDWORD) &l_ByteCount, NULL );...
Page 99: Transceiver Control
RS-485 Transceiver Control The RS-485 hardware supports four modes of hardware transceiver control. You can use hardware transceiver control to enable and disable your transmitters and receivers so that they function on different bus topologies. The following table lists the status of the transmitters and receivers under each transceiver control mode. RS-485 Transceiver Control Modes Mode Transmitter Receiver Four-wire mode Always enabled Always enabled Two-wire mode: DTR Enabled when DTR Always enabled controlled with echo asserted Two-wire mode: DTR Enabled when DTR Enabled when DTR controlled asserted unasserted Two-wire mode: Auto Enabled when Enabled when not Control transmitting data transmitting data...
Page 100 Four-Wire Mode Use the four-wire mode for most full-duplex systems. In this mode, the transmitter and receiver are always enabled. This mode is the default.
Page 101 Two-Wire Mode: DTR Controlled with Echo You can use this mode in half-duplex systems where you need to control the transmitter programmatically. In the DTR-with-echo mode, the transmitter is tri-stated when the DTR signal of the UART (Universal Asynchronous Receiver/Transmitter) is unasserted. To transmit, your application first must enable the transmitter by asserting DTR. After the data is fully transmitted, your application unasserts DTR to disable the transmitter. Because the receiver is always enabled in this mode, you receive packets not only from other devices, but also your transmitter. Thus, your receiver echoes all data you transmit.
Page 102 Two-Wire Mode: DTR Controlled This mode is similar to the two-wire, DTR-with-echo mode. Although this mode uses the same method as the DTR-with-echo mode to control the transmitter, the hardware automatically disables the receiver whenever the transmitter is enabled. Thus, you do not receive the packets sent from your transmitter.
Page 103 Two-Wire Mode: Auto Control In this mode, the serial hardware transparently enables the transmitter and receiver in a two-wire system. Use this mode to remove the burden of transceiver control from your application. The hardware automatically enables the transmitter for each byte to be transmitted. Also, the hardware disables the receiver whenever the transmitter is enabled, so you do not receive the packets sent from your transmitter. Note When you are communicating with a two-wire device, National Instruments recommends that you use the two-wire Auto Control mode. Because this mode handles the transmitter/receiver enabling for a two-wire connection in your hardware, it reduces the software overhead required to perform this operation in your application program. For more information about serial communication in two or four- wire modes, refer to Serial Communication Issues.
Page 104 Setting the RS-485 Transceiver Control Mode in Windows Setting the Default Mode of Operation To set the default mode of operation: Use the Advanced tab in Measurement & Automation Explorer (MAX).
Page 105 Modifying the RS-485 Transceiver Mode Programmatically To modify the RS-485 transceiver mode programmatically: Change the NI-VISA wire mode attribute. The NI-Serial software uses programmatic control codes and the DeviceIoControl Windows function for programming the RS-485 transceiver control mode. Setting the RS-485 Transceiver Control Mode on PCI, PXI, USB, ExpressCard, and PCMCIA Hardware To set and retrieve the RS-485 transceiver control mode using the DeviceIoControl Windows function on PCI, PXI, USB, ExpressCard, and PCMCIA RS-485 hardware, complete the following steps: 1. Add the following lines to your source code: #include <winioctl.h> #include <NiSerial.h> Note You can find the header file NiSerial.h in the NI- Serial folder where you installed your National Instruments software (typically, C:\Program Files\National Instruments\NI-Serial). It is also included on your NI-Serial software CD. 2. The TRANSCEIVER_MODE attribute can have the following values: RS485_MODE_4WIRE RS485_MODE_2W_ECHO RS485_MODE_2W_DTR RS485_MODE_2W_AUTO 3. To set the RS-485 transceiver control mode, use NISERIAL_SET_RS485_MODE and DeviceIoControl. For...
Page 106 example, to set to two-wire Auto Control mode, use the following code: TRANSCEIVER_MODE l_TransceiverMode = RS485_MODE_2W_AUTO; DWORD l_ByteCount; DeviceIoControl ( PortHandle, NISERIAL_SET_RS485_MODE, (LPVOID) &l_TransceiverMode, sizeof (l_TransceiverMode), (LPVOID) NULL, 0, (LPDWORD) &l_ByteCount, NULL ); 4. To retrieve the current RS-485 transceiver control mode, you can use NISERIAL_GET_RS485_MODE and DeviceIoControl with the following code: TRANSCEIVER_MODE l_TransceiverMode; DWORD l_ByteCount; DeviceIoControl ( PortHandle, NISERIAL_GET_RS485_MODE, (LPVOID) NULL, 0, (LPVOID) &l_TransceiverMode, sizeof (l_TransceiverMode), (LPDWORD) &l_ByteCount, NULL ); Setting the RS-485 Transceiver Control Mode on ENET Hardware To set and retrieve the RS-485 transceiver control mode using the...
Page 107 DeviceIoControl Windows function on ENET RS-485 hardware, complete the following steps: 1. Add the following lines to your source code: #include <winioctl.h> #define SERIAL_TM_4WIRE 0x80 #define SERIAL_TM_2W_ECHO 0 x81 #define SERIAL_TM_2W_DTR 0x81 #define SERIAL_TM_2W_AUTO 0 x83 #define IOCTL_SERIAL_SET_TRANSCEIVER_MODE CTL_CODE(FILE_DEVICE_SERIAL_PORT,37,METHOD_BUFFERED,F 2. To set the RS-485 transceiver control mode, use IOCTL_SERIAL_SET_TRANSCEIVER_MODE and DeviceIoControl. For example, to set to two-wire Auto Control mode, use the following code: ULONG bytecount; TRANSCEIVER_MODE transceiver_mode = SERIAL_TM_2W_AUTO; DeviceIoControl( comhandle, IOCTL_SERIAL_SET_TRANSCEIVER_MODE, (PVOID) &transceiver_mode, sizeof(transceiver_mode), (PVOID) NULL, 0, &bytecount, NULL...
Page 108 Setting the RS-485 Transceiver Control Mode in LabVIEW Real-Time Setting the Default Mode of Operation To set the default mode of operation: For PXI: Use the Advanced tab in Measurement & Automation Explorer (MAX) to define the default transceiver control mode. For FieldPoint devices supporting multiple transceiver control modes, follow these steps: Note Without modification, the default mode is set to four- wire. 1. Using an FTP client, download the /ni-rt/system/niserial.dbs file from the LabVIEW Real-Time target. 2. Locate the entry in the niserial.dbs file that says SerialPortName = "COMx", where COMx corresponds to the port you want to modify. 3. In the next line, add the following entry to the niserial.dbs file: TransceiverMode = <Transceiver Mode> where <Transceiver Mode> is: <Transceiver Description Mode> Four-wire mode Two-wire mode: DTR controlled with echo Two-wire mode: DTR controlled...
Page 109 Two-wire mode: Auto Control 4. Copy the file back to its original location on the LabVIEW Real-Time target, replacing the original file. Reboot your LabVIEW Real-Time target for your changes to take effect. For example, to configure COM4 to use two-wire Auto Control mode, the following would appear in the niserial.dbs file: SerialPortName = "COM4" TransceiverMode = 131...
Page 110 Modifying the Transceiver Control Mode Programmatically To modify the transceiver control mode programmatically: In LabVIEW Real-Time, you must use the VISA wire mode attribute to change the RS-485 transceiver control mode programmatically.
Page 111: Bias Resistors
Bias Resistors An RS-485 transmission line enters an indeterminate state if no nodes are transmitting on it. This indeterminate state can cause the receivers to receive invalid data bits from noise picked up on the cable. To prevent a line from receiving these data bits, the transmission line can be forced into a known state by installing two bias resistors at one node on the transmission line. Doing so creates a voltage divider that forces the voltage between the differential pair to be greater than 200 mV, the threshold voltage for the receiver. The following figure shows a transmission line using bias resistors. Transmission Line Using Bias Resistors On the PCI RS-485 two and four-port serial cards, PXI RS-485 two and four-port serial cards, and ENET RS-485 two and four-port serial cards, there are four user-configurable bias resistors in front of each connector. These resistors are socketed and pre-loaded with 620 resistors. They are connected to the receive signals of each port to maintain a known state when the bus is idle. The connections are made as follows: RXD+ and CTS– are pulled up to +5 V RXD– and CTS+ are pulled down to GND Rather than using two 620 resistors at one node, you can increase the value of the resistors and put them at every node. For instance, if there are eight nodes in a system, you can use 4.7 k resistors at each node to effectively achieve the same result. If your application needs termination, an optional external RS-485 DB-9 terminator that provides 120 is available.
Page 112 USB-485 Programmatically Controlled Bias Resistors On the USB-485 hardware, there are programmatically controlled onboard bias resistors. In addition, the USB-485 two and four-port hardware has user-configurable socketed bias resistors. By default, the USB-485 hardware uses the programmatically controlled bias resistors, which are connected to the receive signals of each port to maintain a known state when the bus is idle. The connections are made as follows: RXD+ and CTS– are pulled up to +3.3 V RXD– and CTS+ are pulled down to GND The follwing figure shows a USB transmission line using bias resistors. USB-485 Transmission Line Using Bias Resistors The values of the programmatically controlled bias resistors have been calculated such that there is a voltage of at least 200 mV between the differential pair. Rather than using the programmatically controlled bias resistors, you can load custom values of resistors into the sockets in front of each connector or use external bias resistors. If these resistors are installed, make sure the programmatically controlled bias resistors are disabled. Note Using custom bias resistors on the USB-485 two port may violate the USB suspend current specification. Note The series 25 resistors in the figure above are for short- circuit protection and do not impact serial communication.
Page 113 Setting the USB-485 Programmatically Controlled Bias Resistor Mode The USB-485 hardware can programmatically control the onboard (nonsocketed) bias resistors. By default, these resistors are enabled during normal device operation and disabled during USB suspend. There are two ways to control these resistors: Use the Advanced tab in MAX. If the Enable Dynamic Bias Resistors box is checked, the resistors are enabled automatically whenever a serial port is open during normal operation. If the box is not checked, the resistors are disabled. Your software can enable or disable the bias resistors programmatically by making DeviceIoControl calls to the serial driver.
Page 114 Setting the RS-485 Programmatically Controlled Bias Resistors with DeviceIoControl The NI-Serial software uses programmatic control codes and the DeviceIoControl Windows function for programming the RS-485 bias resistor mode. To set and retrieve the RS-485 bias resistor mode, complete the following steps: 1. Add the following lines to your source code: #include <winioctl.h> #include <NiSerial.h> Note The header file NiSerial.h is included on your NI- Serial software CD. You also can find it in the NI-Serial folder where you installed your National Instruments software (typically, C:\Program Files\National Instruments\NI- Serial). 2. The SERIAL_RS485_BIAS attribute can have the following values: RS485_BIAS_OFF RS485_BIAS_ON 3. To set the RS-485 bias resistor mode, use NISERIAL_SET_RS485_BIAS and DeviceIoControl. For example, to enable programmatically controlled RS-485 bias resistors, use the following code: SERIAL_RS485_BIAS l_SerialRs485Bias = RS485_BIAS_ON; DWORD l_ByteCount; DeviceIoControl ( PortHandle, NISERIAL_SET_RS485_BIAS, (LPVOID) &l_SerialRs485Bias, sizeof (l_SerialRs485Bias), (LPVOID) NULL, 0,...
Page 115 (LPDWORD) &l_ByteCount, NULL ); 4. To retrieve the current RS-485 bias resistor mode, you can use NISERIAL_GET_RS485_BIAS and DeviceIoControl with the following code: SERIAL_RS485_BIAS l_SerialRs485Bias; DWORD l_ByteCount; DeviceIoControl ( PortHandle, NISERIAL_GET_RS485_BIAS, (LPVOID) NULL, 0, (LPVOID) &l_SerialRs485Bias, sizeof (l_SerialRs485Bias), (LPDWORD) &l_ByteCount, NULL );...
Page 116 Retrieving the RS-232 Transceiver State The NI-Serial software returns which mode the RS-232 transceivers are currently operating in, and whether the serial connection is valid. Note Transceiver mode refers to the programmed mode. Transceiver state refers to the physical state of the transceivers (actual operating mode and whether valid or invalid). There are two ways to retrieve the RS-232 transceiver state and tranceiver mode: Read the NI-VISA wire mode attribute to retrieve the transceiver state and the NI-VISA IsPortConnected attribute to retrieve the transceiver mode. The NI-Serial software uses programmatic control codes and the DeviceIoControl Windows function to retrieve the RS-232 transceiver state and transceiver mode. To retrieve the RS-232 transceiver state using the DeviceIoControl Windows function, complete the following steps: 1. Add the following lines to your source code: #include <winioctl.h> #include <NiSerial.h> Note The header file NiSerial.h is included on your NI- Serial software CD. You also can find it in the NI-Serial folder where you installed your National Instruments software (typically, C:\Program Files\National Instruments\NI- Serial). 2. The RS-232 transceiver state attribute is contained within a struct of type SERIAL_RS232_STATE. The struct members and possible values are shown below: Member Values Name PortMode RS232_MODE_DTE RS232_MODE_DCE RS232_MODE_AUTO...
Page 117 Connection SERIAL_CONNECTION_INVALID SERIAL_CONNECTION_VALID 3. To retrieve the current RS-232 transceiver state, use NISERIAL_GET_RS232_STATE and DeviceIoControl with the following code: SERIAL_RS232_STATE l_SerialRs232State; DWORD l_ByteCount; DeviceIoControl ( PortHandle, NISERIAL_GET_RS232_STATE, (LPVOID) NULL, 0, (LPVOID) &l_SerialRs232State, sizeof (l_SerialRs232State), (LPDWORD) &l_ByteCount, NULL );...
Page 118 USB-232 Transceiver Control The USB-232 two and four-port hardware supports both DTE and DCE transceiver modes. By default, the RS-232 transceiver mode is forced to DTE, but you can adjust this in two ways: Use the Advanced tab in MAX. To set the transceiver mode to be used whenever a port is opened, select the desired mode from the transceiver mode pull-down menu. Change the transceiver mode programmatically by making a DeviceIoControl function call to the serial driver. The following table describes the RS-232 modes. RS-232 Modes RS-232 Description Mode Force The transceiver is forced into DTE mode (Default) Force The transceiver is forced into DCE mode Auto The transceiver automatically switches between DTE and DCE modes about four times a second until a valid RS-232 signal is detected Note When using Auto232, if you connect two serial ports set to Auto232, or if valid RS-232 signals are present in both modes, the final mode may be either DTE or DCE. Note A valid RS-232 signal is defined as at least one valid RS-232 voltage detected on any receiver pin (RXD, CTS, DSR, RI, or DCD). The USB-232 hardware also allows you to set and retrieve the state of the of the Ring Indicate (RI) and Data Carrier Detect (DCD) lines along with the Transceiver Mode. Setting the RS-232 Transceiver Mode with DeviceIoControl Setting Ring Indicate (RI) and Data Carrier Detect (DCD) with DeviceIoControl...
Page 119 Setting the RS-232 Transceiver Mode with DeviceIoControl There are two ways to set and retrieve the RS-232 transceiver state: Set and read the NI-VISA wire mode attribute. The NI-Serial software uses programmatic control codes and the DeviceIoControl Windows function to retrieve the RS-232 transceiver state. To set and retrieve the RS-232 transceiver state using the DeviceIoControl Windows function, complete the following steps: 1. Add the following lines to your source code: #include <winioctl.h> #include <NiSerial.h> Note The header file NiSerial.h is included on your NI- Serial software CD. You also can find it in the NI-Serial folder where you installed your National Instruments software (typically, C:\Program Files\National Instruments\NI- Serial). 2. The TRANSCEIVER_MODE attribute can have the following values: RS232_MODE_DTE RS232_MODE_DCE RS232_MODE_AUTO 3. To set the RS-232 transceiver, use NISERIAL_SET_RS232_MODE and DeviceIoControl. For example, to set to Force DCE mode, use the following code: TRANSCEIVER_MODE l_TransceiverMode = RS232_MODE_DCE; DWORD l_ByteCount; DeviceIoControl (...
Page 120 PortHandle, NISERIAL_SET_RS232_MODE, (LPVOID) &l_TransceiverMode, sizeof (l_TransceiverMode), (LPVOID) NULL, 0, (LPDWORD) &l_ByteCount, NULL ); 4. To retrieve the current RS-232 transceiver mode, you can use NISERIAL_GET_RS232_MODE and DeviceIoControl with the following code: TRANSCEIVER_MODE l_TransceiverMode; DWORD l_ByteCount; DeviceIoControl ( PortHandle, NISERIAL_GET_RS232_MODE, (LPVOID) NULL, 0, (LPVOID) &l_TransceiverMode, sizeof (l_TransceiverMode), (LPDWORD) &l_ByteCount, NULL );...
Page 121 Setting Ring Indicate (RI) and Data Carrier Detect (DCD) with DeviceIoControl There are two ways to set and retrieve these RS-232 signals: Set and read the NI-VISA Line RI State and Line DCD State attributes. The NI-Serial software uses programmatic control codes and the DeviceIoControl Windows function to retrieve these RS-232 signals. To retrieve these RS-232 signals using the DeviceIoControl Windows function, complete the following steps: 1. Add the following lines to your source code: #include <winioctl.h> #include <NiSerial.h> Note The header file NiSerial.h is included on your NI- Serial software CD. You also can find it in the NI-Serial folder where you installed your National Instruments software (typically, C:\Program Files\National Instruments\NI- Serial). 2. The SERIAL_RI_OUT attribute can have the following values: SERIAL_RI_ON SERIAL_RI_OFF 3. To set the RS-232 signal RI when the transceiver is in DCE mode, use the following code: DWORD l_ByteCount; DeviceIoControl ( PortHandle, NISERIAL_SET_RI, (LPVOID) NULL, 0,...
Page 122 (LPVOID) NULL, 0, (LPDWORD) &l_ByteCount, NULL ); 4. To clear the RS-232 signal RI when the transceiver is in DCE mode, use the following code: DWORD l_ByteCount; DeviceIoControl ( PortHandle, NISERIAL_CLR_RI, (LPVOID) NULL, 0, (LPVOID) NULL, 0, (LPDWORD) &l_ByteCount, NULL ); 5. To retrieve the current state of the RS-232 signal RI when the transceiver is in DCE mode, use the following code: SERIAL_RI_OUT l_SerialRiOut; DWORD l_ByteCount; DeviceIoControl ( PortHandle, NISERIAL_GET_RI, (LPVOID) NULL, 0, (LPVOID) &l_SerialRiOut, sizeof (l_SerialRiOut), (LPDWORD) &l_ByteCount, NULL ); 6. The SERIAL_DCD_OUT attribute can have the following values:...
Page 123 SERIAL_DCD_ON SERIAL_DCD_OFF 7. To set the RS-232 signal DCD when the transceiver is in DCE mode, use the following code: DWORD l_ByteCount; DeviceIoControl ( PortHandle, NISERIAL_SET_DCD, (LPVOID) NULL, 0, (LPVOID) NULL, 0, (LPDWORD) &l_ByteCount, NULL ); 8. To clear the RS-232 signal DCD when the transceiver is in DCE mode, use the following code: DWORD l_ByteCount; DeviceIoControl ( PortHandle, NISERIAL_CLR_DCD, (LPVOID) NULL, 0, (LPVOID) NULL, 0, (LPDWORD) &l_ByteCount, NULL ); 9. To retrieve the current state of the RS-232 signal DCD when the transceiver is in DCE mode, use the following code:...
Page 124 SERIAL_DCD_OUT l_SerialDcdOut; DWORD l_ByteCount; DeviceIoControl ( PortHandle, NISERIAL_GET_DCD, (LPVOID) NULL, 0, (LPVOID) &l_SerialDcdOut, sizeof (l_SerialDcdOut), (LPDWORD) &l_ByteCount, NULL );...
Page 125: Status Leds
Status LEDs The ENET serial and USB serial two and four-port hardware uses bicolor light-emitting diodes (LEDs) to indicate device and port status. USB LED Descriptions ENET LED Descriptions ENET PWR/RDY LED Signaling...
Page 126 USB LED Descriptions The USB serial two and four-port hardware uses bicolor LEDs to indicate device and port status. The following table describes these LEDs; the following figure shows their location. Description Ready Dim Red—Powered, but not connected to USB (USB-485/4 only) Red—Powered and connected to USB, but not fully configured Yellow—Device is ready (normal operation) Blinking Red or Red-Yellow—Device error. Contact NI. Port x Solid Red—Port is open, but no valid signals detected (USB-232 only) Solid Green—Port is open Blinking Yellow—Port is transmitting Blinking Green—Port is receiving Alternated Blinking Green/Yellow—Port is transmitting and receiving Blinking Red—Port error (framing error, FIFO overrun, or parity error) 1 READY LED...
Page 127 2 PORT LEDs USB-Serial Hardware LEDs...
Page 128 ENET LED Descriptions The ENET serial hardware uses bicolor LEDs to indicate device and port status. The following table describes these LEDs; the following figure shows their location. Description PWR/RDY Flashes rapidly at start-up while performing self tests and when acquiring network parameters. A steady yellow state indicates the box is ready for operation. Slow flashing pattern indicates an error occurred. LINK 10/100 Indicates the serial ENET interface detected a twisted pair (10Base-T or 100Base-TX) link. The color indicates the connection speed. If yellow, the speed is 10 Mbits/s. If green, the speed is 100 Mbits/s. Indicates the serial ENET interface is transmitting to the Ethernet network. Indicates the serial ENET interface is receiving Ethernet network traffic. PORT x Indicates which serial ports are open. Power/Ready LED Ethernet LEDs Serial Port LEDs Power Switch Four-Port Serial ENET Hardware LEDs...
Page 129 ENET PWR/RDY LED Signaling This topic describes how to interpret the PWR/RDY LED error codes. The PWR/RDY LED has several purposes on the serial ENETs. When you first power on the unit, the PWR/RDY LED alternates rapidly between red and yellow while it completes its power-on self-tests and acquires network parameters. When the tests complete successfully and the IP address is assigned from either nonvolatile memory or the network, the PWR/RDY LED remains steady yellow, indicating that the unit is ready to operate. The PWR/RDY LED also alternates rapidly between red and yellow while the device is in network configuration mode. At other times, the PWR/RDY LED blinks slowly in a recognizable pattern to alert you of internal errors. Use the following steps to interpret and record the pattern that the PWR/RDY LED flashes, and then contact National Instruments. Note By recording the PWR/RDY LED error messages before calling National Instruments, you can save yourself time, and customer support can answer your questions more accurately and efficiently. Do not switch off power to your serial ENET before recording the flashing PWR/RDY LED pattern. PWR/RDY LED signaling can report up to 81 different errors. The errors are numbered from 11 to 99 and are reported through sequences of PWR/RDY LED flashes. Note There is no zero in any error message. This means that error message numbers 0–10, 20, 30, 40, 50, 60, 70, 80, and 90 are not possible.
Page 130 Step 1. Count the Long Flashes A three-second interval, during which the PWR/RDY LED is yellow, separates each repetition of the sequence. The sequence begins with a series of long one-second flashes—that is, one second red, one second yellow. These long flashes represent the digit in the tens column. There can be one to nine long flashes, which represent digits 1 through 9. For example, one long flash represents the digit 1 in the tens column, and nine long flashes represent the digit 9 in the tens column.
Page 131 Step 2. Count the Short Flashes The long flashes are followed by shorter flashes; each short flash lasts about one-fifth of a second—that is, one-fifth of a second red, one-fifth of a second yellow. These short flashes represent the digit in the ones column. Again, there can be one to nine flashes, which represent the digits 1 through 9. For example, one short flash represents the digit 1 in the ones column, and nine short flashes represent the digit 9 in the ones column. Using this method, the PWR/RDY LED flashes the following sequence to represent error message 11: <three seconds yellow> <one long red flash> <one short red flash> <three seconds yellow>... The PWR/RDY LED flashes the following sequence to represent error message 31: <three seconds yellow> <three long red flashes> <one short red flash> <three seconds yellow>...
Page 132 Step 3. Record Your Error Message Number When you have computed your error message number, write it down and also note the ON/OFF state of the LINK, TX, and RX LEDs. Have this information available when calling National Instruments.
Page 133: Connector Descriptions
Connector Descriptions The following topics describe serial hardware connectors. Connecting Cables Connecting Two-Wire Devices DB-9 Connector Modular Jack Connector DB-25 Connector 68-Pin Connector 100-Pin Connector...
Page 134: Connecting Cables
Connecting Cables For the PCMCIA and ExpressCard hardware, two-port PCI and PXI serial hardware, and all USB and ENET hardware, you can use the standard DB-9 connector found on most serial cables. To use the DB-9 connector with the four-port PCI and PXI serial hardware, you need the 10-position modular jack to DB-9 cable, which is available from National Instruments. You can also use a DB-25 connector with the four-port serial boards by ordering the 10-position modular jack to DB-25 converter cable from National Instruments. The eight-port serial boards include a pig tail cable adapter, providing eight standard DB-9 connectors. The 16-port boards include a breakout box, providing 16 standard DB-9 connectors. Note To achieve the specified isolation voltage for four-port isolated PCI or PXI serial boards, use only the 10-position modular jack to DB-9 cable included in your four-port isolated PCI or PXI serial board kit. For more information about cable connectors, see the connector description topics.
Page 135 Connecting Two-Wire Devices The NI RS-485 hardware is designed to work with either two or four-wire devices. If you are using a two-wire device, refer to the device documentation for specific wiring instructions. In general, half-duplex networks use a single twisted pair of wires for communication in both directions, so you must connect both the transmitter and the receiver at each end of the same pair of wires. For example, to connect an RS-485 data acquisition device to a port on your board using half-duplex communication, you need a single twisted pair of wires. At the board, connect the TXD+ and RXD+ signals (pins 8 and 4 on a DB-9 connector, pins 5 and 20 on a DB-25 connector) together and to one wire. Connect the other end of this wire to both the TXD+ and RXD+ signals on the data acquisition device. Use the same method to connect the TXD– and RXD– signals (pins 9 and 5 on a DB-9 connector, pins 22 and 7 on a DB-25 connector) to the second wire. For information about setting the transceiver mode for two-wire communication, refer to RS-485 Transceiver Control. For more information about duplex architectures, refer to Serial Port Information.
Page 136 DB-9 Connector The following figure and table give the pin locations and descriptions of the DB-9 connector, the 10-position modular jack to DB-9 cable, the cable adapter for the eight-port board, and the DB-9 connectors to the 16-port breakout box. DB-9 Connector Pin Locations DB-9 Pin Descriptions 232 Signal DB-9 Pin 485 Signal DCD* CTS+ (HSI+) RTS+ (HSO+) DTR* RXD+ RXD– DSR* CTS– (HSI–) RTS– (HSO–) TXD+ TXD– * These signals are "No Connect" on the isolated 232 boards or ports 9– 16 of the PCI-232/16 legacy board.
Page 137 Modular Jack Connector The following figure and table give the pin locations and descriptions of the 10-position modular jack. 10-Position Modular Jack Pin Locations 10-Position Modular Jack Pin Descriptions 10-Position 232 Signal 485 Signal Modular Jack Pin DCD* CTS+ (HSI+) RTS+ (HSO+) DTR* RXD+ RXD– DSR* CTS– (HSI–) RTS– (HSO–) TXD+ TXD– No Connect No Connect * These signals are "No Connect" on the isolated 232 ports.
Page 138 DB-25 Connector The following figure and table give the pin locations and descriptions of the DB-25 connector, which is on the optional 10-position modular jack to DB-25 cable. DB-25 Connector Pin Locations DB-25 Pin Descriptions DB-25 Pin 232 Signal 485 Signal RTS+ (HSO+) CTS+ (HSI+) RTS– (HSO–) TXD+ DSR* CTS– (HSI–) RXD– DCD* DTR* RXD+ TXD– Pins not listed in this table are No Connect. * These signals are "No Connect" on the isolated 232 ports. The following figure shows how to connect the cables when you install a four-port PXI serial board.
Page 139 Connecting the Cables to a Four-Port PXI Serial Board...
Page 140: Pin Connector
68-Pin Connector The following figure and table give the pin locations and descriptions of the 68-pin connector. 68-Pin Connector Pin Locations 68-Pin Connector Pin Descriptions 68-Pin Connector Port 485 D-Sub 9 232 D-Sub 9 1 2 3 4 5 6 7 8 Signal Connector Signal Connector 66 57 49 40 32 23 15 6 RXD– 5 68 59 51 42 34 25 17 8 CTS+ 2 65 56 48 39 31 22 14 5 RTS+ 3 64 55 47 38 30 21 13 4 RXD+ 4 60 60 43 43 26 26 9 9 GND...
Page 141 67 58 50 41 33 24 16 7 TXD– 9...
Page 142 100-Pin Connector The following figure and table give the pin locations and descriptions of the 100-pin connector. 100-Pin Connector Pin Locations 100-Pin Connector Pin Descriptions 100-Pin Connector Port 232 D‑Sub 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Signal Connector 2 46 6 42 10 38 14 34 — — — — — — — — DCD* 1 3 47 7 43 11 39 15 35 18 32 20 30 22 28 24 26 RXD 4 48 8 44 12 40 16 36 19 33 21 31 23 29 25 27 TXD...
Page 143 55 99 59 95 63 91 67 87 — — — — — — — — * These signals are not supported on ports 9–16 of the PCI-232/16 and PXI-8420/16 serial boards.
Page 144: Serial Port Information
Serial Port Information The following topics describe the RS-232, RS-422, and RS-485 standards and explain some of the issues involved with these types of serial communication. RS-232 RS-422 RS-485 Serial Communication Issues Duplex Architectures Full Duplex Half Duplex RS-485 Termination Bias Resistors RS-232 DTE versus DCE The following table lists the features of the RS-232, RS-422, and RS-485 standards. RS-232, RS-422, and RS-485 Features Feature RS-232 RS-422 RS-485 Type of transmission lines Single ended Differential Differential Maximum number of drivers Maximum number of receivers 1 Maximum cable length 50 ft 4,000 ft 4,000 ft Maximum data rate 20 kbytes/s 10 Mbytes/s 10 Mbytes/s Maximum CMV ± 25 V ±7 V +12 to –7 V Driver output 5 to 25 V 2 to 6 V...
Page 145 RS-232 As specified in the ANSI/EIA-232-D Standard, Interface Between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary Data Interchange, RS-232 standardizes serial communication between computers and between computer terminals and modems. Many applications use the RS-232 standard to interface peripherals to personal computers. RS-232 uses transmission lines in which the state of each signal is represented by referencing the voltage level of a single line to ground. RS-232 was designed for serial communication up to distances of 50 ft and with data rates up to 20 kbytes/s. However, because of improvements in line drivers and cabling, it is possible to increase the actual performance of the bus past the limitations on speed and distance recommended in the specification.
Page 146 RS-422 As specified in the EIA/RS-422-A Standard, Electrical Characteristics of Balanced Voltage Digital Interface Circuits, RS-422 defines a serial interface much like RS-232. However, RS-422 uses balanced (or differential) transmission lines. Balanced transmission lines use two transmission lines for each signal. The state of each signal is represented, not by a voltage level on one line referenced to ground as in RS-232, but rather by the relative voltage of the two lines to each other. For example, the TX signal is carried on two wires, wire A and wire B. A logical 1 is represented by the voltage on line A being greater than the voltage on line B. A logical 0 is represented by the voltage on line A being less than the voltage on line B. Differential voltage transmission creates a signal that is more immune to noise as well as voltage loss due to transmission line effects. Thus, you can use RS-422 for longer distances (up to 4,000 ft) and greater transmission speeds (up to 10 Mbytes/s) than RS-232.
Page 147 RS-485 As specified in the EIA-485 Standard, Standard for Electrical Characteristics of Generators and Receivers for Use in Balanced Digital Multipoint Systems, RS-485 expands on the RS-422 standard by increasing the number of devices you can use from 10 to 32 and by working with half-duplex bus architectures. Unlike the RS-422 standard, RS-485 addresses the issue of using multiple transmitters on the same line. RS-485 defines the electrical characteristics necessary to ensure adequate signal voltages under maximum load, as well as short-circuit protection. RS-485 can also withstand multiple drivers driving conflicting signals at the same time.
Page 148 Serial Communication Issues The following topics explain some serial communication issues, including duplex architectures, termination methods, bias resistors, and types of connecting equipment. Duplex Architectures Full Duplex Half Duplex RS-485 Termination Bias Resistors RS-232 DTE versus DCE...
Page 149 Duplex Architectures Duplex refers to the means of bandwidth usage in a serial system. The two common means of bi-directional serial communication are full duplex and half duplex. Half-duplex communication involves a transmitter and a receiver connected to each end of the same wire or pair of wires. Because the same transmission line both sends and receives data, devices cannot send data in both directions at the same time. First, one device transmits over the wire(s) to the receiver of the second device. When the first device finishes transmitting, both devices switch the connections from their transmitter to their receiver, or vice versa. The device that was receiving data can then transmit over the line. In full-duplex communication, the devices use a separate wire (or pair of wires) for simultaneous transmission in each direction. Thus, the devices do not switch between transmitting and receiving. In a differential serial bus (such as RS-422 or RS-485), a half-duplex system transmits and receives over the same twisted pair of wires. Thus, half-duplex communication is often referred to as two-wire communication. Likewise, full-duplex communication is often referred to as four-wire communication, because the full-duplex system uses a separate pair of wires for communication in each direction.
Page 150: Full Duplex
Full Duplex A typical full-duplex multidrop bus architecture involves a master-slave protocol. Only one device, the master, can control access to the bus. All other devices are slaves. Slave devices must wait for the master to give them access to the bus. In a typical full-duplex system, one transmission line connects the bus master transmitter to all of the slave receivers. A second transmission line connects all of the slave transmitters to the bus master receiver. Because each transmission line has two separate wires, a full-duplex system is often referred to as a four-wire system. The master uses four-wire mode, and the slaves use two-wire mode. The following figure shows a typical full-duplex system. Typical Full-Duplex System...
Page 151: Half Duplex
Half Duplex A typical half-duplex multidrop bus architecture also involves a master- slave protocol. However, in a half-duplex system, all transmitters and receivers are connected to the same transmission line. A half-duplex system is often referred to as a two-wire system. The following figure shows a typical half-duplex system. Typical Half-Duplex System...
Page 152 RS-485 Termination Because each differential pair of wires is a transmission line, you must properly terminate the line to prevent reflections. A common method of terminating a two-wire multidrop RS-485 network is to install terminating resistors at each end of the multidrop network. If you daisy-chained multiple instruments together, you need a terminating resistor at only the first and last instruments. The terminating resistor should match the characteristic impedance of the transmission line (typically 100 to 120 ). You can order an optional DB-9 RS-485 termination connector that contains embedded terminating resistors for easy termination from National Instruments. For ordering information, contact National Instruments. The following figure shows a multidrop network using terminating resistors. Multidrop Network Using Terminating Resistors The following figure shows a full-duplex network using terminating resistors. Full-Duplex Network Using Terminating Resistors...
Page 153 Bias Resistors An RS-485 transmission line enters an indeterminate state if no nodes are transmitting on it. This indeterminate state can cause the receivers to receive invalid data bits from noise picked up on the cable. To prevent a line from receiving these data bits, the transmission line can be forced into a known state by installing two bias resistors at one node on the transmission line. Doing so creates a voltage divider that forces the voltage between the differential pair to be greater than 200 mV, the threshold voltage for the receiver. For more information about RS-485 bias resistors, refer to Using Your Serial Hardware.
Page 154 RS-232 DTE versus DCE In the RS-232 specification, DTE (Data Terminal Equipment) and DCE (Data Communications Equipment) refer to the types of equipment on either end of a serial connection. In general, DTE and DCE refer to computer equipment and modems, respectively. Because the RS-232 specification mainly involves connecting a DTE directly to a DCE and vice versa, the pinouts are defined so that cabling is simple. That is, a cable connected a computer to a modem by wiring pin 1 to pin 1, pin 2 to pin 2, and so on. This method is known as straight-through cabling. The following figure shows straight-through cabling in a DTE-to-DCE interface. Straight-Through Cabling in a DTE-to-DCE Interface Straight-through cabling is still the standard method to connect a modem to your PC. However, because many applications use serial communication to connect two or more DTEs without modems, the cabling becomes more complicated. If two DTEs are wired together using a straight-through cable, one transmitter is connected to the other transmitter, and one receiver is connected to the other receiver. In this setup, no transmissions can occur. Thus, these applications must use a cabling scheme that connects the transmitter on one device to the receiver on the other device and vice versa. This method is known as null-modem cabling, because it replaces the two modems that traditional RS-232 applications would require between the two DTEs. To communicate from one DTE serial port to another, use a null-modem cable. The following figure shows null-modem cabling in a DTE-to-DTE interface. Null-Modem Cabling in a DTE-to-DTE Interface PCI, PXI, USB (one port only), ENET, ExpressCard, and PCMCIA RS-...
Page 155 232 ports are DTE serial ports. USB-232 (two and four port only) can be configured to DTE or DCE. Refer to USB-232 Transceiver Control for more information.
Page 156: Uninstalling The Hardware And Software
Uninstalling the Hardware and Software The following topics describe how to uninstall your serial hardware and the NI-Serial software. Delete a Serial Interface Uninstall Software from Your LabVIEW RT Target Uninstall the Windows Software...
Page 157 Delete a Serial Interface Before you physically remove a serial interface from your Windows system, follow these steps to remove the hardware information: 1. Launch MAX. 2. Expand the Devices and Interfaces directory by clicking the + next to the folder. 3. Right-click on your serial interface and select Delete from the drop-down menu that appears. 4. When prompted, click the Yes button to confirm the removal of your interface. 5. MAX automatically updates the list of installed serial interfaces. You can also select View»Refresh to update the list. On LabVIEW RT, it is not necessary to programmatically delete hardware from the system. Simply power down your RT controller and remove the hardware. When you power on your RT controller again, the ports are automatically removed from the system. You may need to refresh MAX to see the changes.
Page 158 Uninstall Software from Your LabVIEW RT Target To uninstall the NI-Serial software from your LabVIEW RT target, complete the following steps: 1. Launch MAX. 2. Expand Remote Systems by clicking the + next to it. 3. Find your remote system in the list and expand it. 4. Right-click Software and select Add/Remove Software. 5. In the Add/Remove Software window, click NI-Serial and select Uninstall the Feature. 6. Click Next to start the software download. Click Finish when the download is complete.
Page 159 Uninstall the Windows Software Before you uninstall the NI-Serial software, you must remove the hardware information from your system, as described in Delete a Serial Interface. To uninstall the NI-Serial software, complete the following steps: 1. Select Start»Control Panel. 2. On Windows 2000/XP/Server 2003, double-click the Add/Remove Programs icon. On Windows Vista, double-click the Programs and Features icon. 3. Select National Instruments Software in the list and click the Change/Remove button on Windows 2000/XP/Server 2003 or the Uninstall/Change button on Windows Vista. 4. Select the software components you want to remove and click the Remove button. The uninstallation program removes all folders, utilites, and registry entries associated with the NI-Serial software. 5. Shut down Windows, power off your computer, and physically remove the serial interfaces from your system. The uninstallation program removes only items that the setup wizard installed. If you added anything to a directory that the setup wizard created, the uninstallation program does not delete that directory. You must remove any remaining components yourself. To reinstall the hardware and software, refer to Install the Hardware and NI-Serial Software Installation.
Page 160: Troubleshooting And Frequently Asked Questions
Troubleshooting and Frequently Asked Questions The following topics describe how to troubleshoot problems and answer some common questions. Verify Installation and Troubleshoot NI-Serial Problems Frequently Asked Questions...
Page 161 Verify Installation and Troubleshoot NI-Serial Problems The NI-Serial Troubleshooting Wizard supports ports only on your local Windows system. It does not test your LabVIEW Real-Time serial ports. To verify the hardware and software installation and troubleshoot NI- Serial problems, follow these steps to run the Troubleshooting Wizard: 1. Launch MAX. 2. Select Help»Troubleshooting»NI-Serial Troubleshooting Wizard. The Troubleshooting Wizard tests your serial interface and displays the results as shown below. NI-Serial Troubleshooting Wizard The Troubleshooting Wizard verifies that your serial driver is installed properly, that the configuration of your hardware does not conflict with anything else in your system, and that the serial driver can communicate with your hardware correctly. To view online help for the Troubleshooting Wizard, click the Help button.
Page 162: Frequently Asked Questions
Frequently Asked Questions How do I force Windows to detect my PCI, PXI, or PCMCIA hardware? How do I force Windows to detect my USB hardware? How do I force Windows to detect my ExpressCard hardware? How can I determine which type of serial hardware I have installed? Why does my PCI/PXI serial card display the wrong serial number? How can I determine which version of the NI-Serial software I have installed? How do I troubleshoot problems? How can I determine whether my hardware and software are installed properly? How can I repair my NI-Serial software? How can I determine which port is associated with COMx? How can I change the COM numbers of my National Instruments serial ports? Why can't I make changes to my settings in MAX on Windows Vista? Why does my hardware keep reappearing after I delete it on Windows Vista? How many serial ports can I have on my machine? How many interrupts are required for my serial interface? How do I resolve serial USB power conflicts? What is the difference between USB 2.0 and USB 1.1 and can I use the USB serial hardware in USB 2.0 networks? Why isn't the Auto232 transceiver mode on my USB-232 working? Why am I seeing poor performance on Windows XP when I use multiple USB serial interfaces? Why did my USB serial ports enumerate backward? How do I access my serial ENET interface using the hostname? How do I communicate with serial ENET interfaces located on other subnets?
Page 163 Why does the NI Ethernet Device Configuration utility list my serial ENET interface as *BUSY* when I know my network uses DHCP? Why doesn't my serial ENET interface show up in the NI Ethernet Device Configuration utility? Why did my application work with a plug-in interface but times out with a serial ENET interface? What is the relationship between bits per second, throughput, and bus utilization? What happens to data sent to a closed serial port? Why do loopback tests of large data transfers sometimes have problems? Does the serial hardware have built-in support for protocols such as SDLC and ModBus? How do I use 9 data bit framing? Can I use NI serial hardware with a non-Windows platform? Can I use USB serial hardware, Ethernet serial hardware, and plug-in serial hardware in the same computer at the same time?
Page 164 How do I force Windows to detect my PCI, PXI, or PCMCIA hardware? If your serial hardware does not show up in the device manager, Windows did not detect your hardware. To solve this problem, complete the following steps: 1. Select Start»Control Panel and double-click the System icon. 2. Select the Hardware tab and click the Device Manager button. 3. Double-click the Multifunction Adapters icon. 4. From the Multifunction adapters list, right-click the National Instruments interface that was not detected, as shown in the following figure. (This example shows a PCI interface.) Selecting an Interface to Uninstall 5. Choose the Uninstall option. 6. In the Confirm Device Removal dialog box, click the OK button to remove the hardware information.
Page 165 7. Click the Scan for Hardware Changes icon at the top of the Device Manager window. 8. Windows should automatically detect your hardware.
Page 166 How do I force Windows to detect my USB hardware? If your USB hardware does not show up in the device manager, Windows did not detect your hardware. To solve this problem, complete the following steps: 1. Select Start»Control Panel and double-click the System icon. 2. Select the Hardware tab and click the Device Manager button. The Device Manager window should appear as shown below. 3. Double-click the Ports (COM & LPT) icon. Verify that all USB serial communication ports are displayed without exclamation marks (!). If any USB serial port has an exclamation mark, right- click the port and select Uninstall. 4. Double-click the Universal Serial Bus Controllers icon. Verify that no USB Composite Devices have exclamation marks (!). If any USB Composite Device has an exclamation mark, right-click the port and select Uninstall. 5. Click the Scan for Hardware Changes icon at the top of the Device Manager window. 6. Windows should automatically detect your hardware. 7. If any of your serial ports are still not visible, disconnect and reconnect the USB serial hardware to a different USB port and return to step 2.
Page 168 How do I force Windows to detect my ExpressCard hardware? If your serial hardware does not show up in the device manager, Windows did not detect your hardware. To solve this problem, complete the following steps: 1. Select Start»Control Panel and double-click the System icon. 2. Select the Hardware tab and click the Device Manager button. The Device Manager window should appear as shown below. 3. Double-click the Ports (COM & LPT) icon. Verify that all ExpressCard serial communication ports are displayed without exclamation marks (!). If any ExpressCard serial port has an exclamation mark, right-click the port and select Uninstall. 4. Double-click the Universal Serial Bus Controllers icon. Verify that no USB Composite Devices have exclamation marks (!). If any USB Composite Device has an exclamation mark, right-click the port and select Uninstall. 5. Click the Scan for Hardware Changes icon at the top of the Device Manager window. 6. Windows should automatically detect your hardware.
Page 170 How can I determine which type of serial hardware I have installed? To view the serial hardware installed on your Windows system, complete the following steps: 1. Launch MAX. 2. Under My System, expand the Devices and Interfaces directory by clicking on the + next to the folder. MAX lists your installed serial hardware under Devices and Interfaces, as shown in the following figure. To view the serial hardware installed on your LabVIEW Real-Time controller, complete the following steps: 1. Launch MAX. 2. Expand Remote Systems by clicking the + next to the folder. 3. Find your RT controller in the list and expand it. 4. Expand the Devices and Interfaces directory. 5. Expand the Serial entry. MAX lists your installed serial hardware under Serial, as shown in the following figure.
Page 172 Why does my PCI/PXI serial card display the wrong serial number? If you swap one PCI/PXI serial card for another of the exact same type, the serial number shown in the device manager and MAX may not change. This happens because Windows cannot distinguish the old hardware from the new. To fix this problem, delete the interface from the system and either scan for new hardware in the device manager or restart your computer. This forces Windows to reinstall your hardware, and the correct serial number should be displayed.
Page 173 How can I determine which version of the NI- Serial software I have installed? You can use MAX to view your NI-Serial software version.
Page 174 How do I troubleshoot problems? Use the NI-Serial Troubleshooting Wizard. This wizard verifies that your serial hardware and the NI-Serial software are installed correctly and working properly.
Page 175 How can I determine whether my hardware and software are installed properly? Use the NI-Serial Troubleshooting Wizard. This wizard verifies that your serial hardware and the NI-Serial software are installed correctly and working properly.
Page 176 How can I repair my NI-Serial software? To repair the NI-Serial software, complete the following steps: 1. Select Start»Control Panel. 2. On Windows 2000/XP/Server 2003, double-click the Add/Remove Programs icon. On Windows Vista, double-click the Programs and Features icon. 3. Select National Instruments Software in the list and click the Change/Remove button on Windows 2000/XP/Server 2003 or the Uninstall/Change button on Windows Vista. 4. Select the software components you want to repair and click the Repair button. The repair checks all utilities and registry entries associated with the NI-Serial software and repairs or replaces files as necessary. 5. Restart the computer to complete the repair process. 6. Use the NI-Serial Troubleshooting Wizard to verify that your software has been repaired and is working properly.
Page 177 How can I determine which port is associated with COMx? To determine which physical port is associated with COMx, complete the following steps: 1. Launch MAX. 2. Expand the Devices and Interfaces directory by clicking on the + next to the folder. MAX lists your installed serial hardware under Devices and Interfaces. 3. Click your serial interface in the device tree. The right window displays information on what COM number is associated with each physical port on your serial interface.
Page 178 How can I change the COM numbers of my National Instruments serial ports? Select a new COM number from the COM Port Number control of the Advanced MAX tab and click Save.
Page 179 Why can't I make changes to my settings in MAX on Windows Vista? To make changes in MAX on Windows Vista, follow these steps to launch MAX with administrative privileges: 1. If MAX is open, close it. 2. Find the MAX icon on the desktop or by going to Start»Programs»National Instruments»Measurement & Automation. 3. Right-click on the MAX icon and select Run as administrator. You must enter an administrative password if you are not an administrator. You should now be able to modify and save settings in MAX.
Page 180 Why does my hardware keep reappearing after I delete it on Windows Vista? Microsoft has changed the hardware removal behavior on Windows Vista. When you delete a piece of hardware, Windows Vista automatically rescans for new hardware. If you delete more than one piece of hardware at the same time, the first piece is added back to the system when you delete the second piece. To prevent this behavior, you must remove each piece of hardware after you delete it from MAX or the device manager.
Page 181 How many serial ports can I have on my machine? You can have up to 256 serial ports.
Page 182 How many interrupts are required for my serial interface? If you have a shared IRQ board or an isolated board, you need one interrupt per board. Serial ENET and serial USB interfaces do not require interrupts.
Page 183 How do I resolve serial USB power conflicts? The USB-232, USB-232/2, USB-232/4, USB-485, and USB-485/2 are high- power bus-powered devices that require more than 100 mA during normal operation. Thus, they must be plugged into an externally powered hub that can deliver up to 500 mA per USB port. If the USB network does not have enough power to support the USB serial hardware, and a system dialog box informs you that there is not enough power for the device, reconnect the hardware to an externally powered hub. The USB-485/4 is a self-powered device that requires external power. If the device is plugged into a USB port, and the device does not have power, it will not enumerate and the ports will not show in the Device Manager. To ensure proper port enumeration, always make sure the USB-485/4 has external power before connecting it to the USB network.
Page 184 What is the difference between USB 2.0 and USB 1.1, and can I use the USB serial hardware in USB 2.0 networks? The USB 2.0 specification replaces the USB 1.1 specification and adds a high-speed mode of operation (480 Mbit/s) to the previously existing full- speed (12 Mbit/s) and low-speed (1.5 Mbit/s) modes of operation. Because USB 2.0 expands on the features of USB 1.1 while preserving backward device compatibility, you can use most full-speed and low- speed devices with either USB 2.0 high-speed networks or USB 1.1 full- speed networks. USB-232/485 devices are USB 2.0 full-speed compliant, so you can use them in either high-speed (USB 2.0 hubs) or full-speed (USB 1.1 hubs) networks.
Page 185 Why isn't the Auto232 transceiver mode on my USB-232 working? The Auto232 mode of operation allows you to connect to either a RS-232 DTE or DCE device using either a null-modem or straight-through cable. The USB-232 port will automatically switch approximately every 250 ms between DTE and DCE operating modes until at least one RS-232 receiver line (RX, CTS, DSR, RI, or DCD) has a valid voltage. Auto232 is available on the USB-232/2 and USB-232/4, and is not available on the USB-232 (single port). Not all devices and applications can take advantage of this feature: Some devices can generate valid voltages on receive lines for both modes, even though the device itself is only DTE or DCE. Thus, these devices may not operate correctly when using Auto232 mode. Some applications immediately start communicating after a COM port is open, thus not allowing enough time for the proper operating mode to be selected. Some cabling schemes short RI, DCD, and DSR together. While this does not present a problem in DTE mode, these signals are driven when in DCE mode. Thus, by shorting the signals together, the outputs will be double (or triple) driven which may cause signal noise or other artifacts. Use a straight-through cable instead. If problems with Auto232 can not be resolved, set the USB-232 to the correct mode (DTE or DCE) for your device and application. By default, the USB-232 ports are set to DTE mode.
Page 186 Why am I seeing poor performance on Windows XP when I use multiple USB serial interfaces? Windows XP system performance may be reduced when multiple USB- 232 and USB-485 devices are installed. This can cause slow screen updating (mouse and window movements) and reduced task switching performance. This problem is addressed in Windows XP Service Pack 1. To obtain Windows XP Service Pack 1, use Windows Update, or contact Microsoft at www.microsoft.com.
Page 187 Why did my USB serial ports enumerate backward? If you use a dual-boot system (Windows XP and Windows 2000), the COM ports may enumerate out of order after switching operating systems. This is because the device firmware is downloaded when the device is first powered. Because the firmware images for operation under Windows 2000 and Windows XP are different, and the USB bus power may not be cycled during a reboot, it is possible to run the incorrect firmware for the current operating system. You can fix this by disconnecting and reconnecting the USB-232 or USB-485 from the USB port or hub (and disconnecting power on the USB-485/4) to force the appropriate firmware to be downloaded.
Page 188 How do I access my serial ENET interface using the hostname? If you want to use the same hostname that the device is configured with and you know its IP address, skip to the next step. Otherwise, run the NI Ethernet Device Configuration utility. (You must use a computer on the same subnet as the device.) Refer to Viewing Network Settings for more information about the NI Ethernet Device Configuration utility. Verify the device is present on the network by pinging the IP address of your device. Ping is a network utility that sends a packet to a device/host on the network, then waits for it to be echoed back, which indicates an active device/host. Find the directory where ping is installed and type in the following command: ping IPaddress where IPaddress is the IP address assigned to your serial device server. When your device responds to the ping requests, repeat this procedure, but this time using the hostname: ping hostname If your device fails to respond when using the hostname, the DNS entry for the device is incorrect. If the network parameters were statically (manually) assigned, the hostname must be manually entered in your network's Domain Name Server (DNS) table before you can use the hostname to communicate with your device. Have your network administrator enter this information. You also can manually check that the device's hostname has been entered in the DNS table by using NSLookup. This network utility queries the DNS for entries in the DNS table. You can use NSLookup to determine the hostname associated with any particular IP address listed in theDNS table. Find the directory where NSLookup is installed and type in the following command: nslookup IPaddress where IPaddress is the IP address you want to look up. Alternately, to determine the IP address associated with a particular hostname, type in the following command instead:...
Page 189 nslookup hostname If you still cannot communicate with your device, contact National Instruments.
Page 190 How do I communicate with serial ENET interfaces located on other subnets? Verify that the device is present on the network by pinging the IP address of your device. Find the directory where ping is installed and type in the following command: ping IPaddress where IPaddress is the IP address assigned to your serial device server. Confirm that the gateway settings of the device are set properly. To do this, run the NI Ethernet Device Configuration utility on a computer on the same subnet as the device. Confirm that the gateway settings of the host machine are set properly. To view your network settings, find the directory where ipconfig is installed and run it. If you need more information, you can run ipconfig with the /all option by typing ipconfig /all. This shows all settings for your machine. Be sure to use the settings for the Ethernet adapter you are using to communicate with the serial device server.
Page 191 Why does the NI Ethernet Device Configuration utility list my serial ENET interface as *BUSY* when I know my network uses DHCP? For up to one minute, the serial device server attempts to retrieve network parameters from a DHCP server. During this time, *BUSY* appears in the utility display. If this status does not change, there are several reasons why DHCP may fail to respond. One of the most likely reasons is that your subnet has no more available addresses to assign using DHCP. Consult your network administrator to determine the specific reason for the problem.
Page 192 Why doesn't my serial ENET interface show up in the NI Ethernet Device Configuration utility? Allow at least 90 seconds for the serial device server to complete its power-on self tests before launching device configuration or clicking Refresh. Communication between the NI Ethernet Device Configuration utility and the serial device server is not guaranteed. Though unlikely, it is possible that the communication gets lost in the network. Click Refresh more than once before concluding that the device is not discovered. Verify that the serial device server shares the same subnet as the computer running the NI Ethernet Device Configuration utility. The NI Ethernet Device Configuration utility cannot communicate with devices through gateways on the network and will not discover devices on another subnet.
Page 193 Why did my application work with a plug-in interface but times out with a serial ENET interface? Because the serial device server is a network device, it is dependent on network conditions for timely communications. An unpredictable delay is associated with using the remote serial ports. Applications may require longer serial timeouts to compensate for this delay. However, different applications handle serial timeouts differently, and each must be adjusted individually to account for your network conditions.
Page 194 What is the relationship between bits per second, throughput, and bus utilization? The term bits per second (bps) refers to the bit rate of data transfer, with 1/bps being the length of time required to transmit one bit. Throughput is the actual data transfer measured by amount of data transmitted time required to transmit Bus utilization is the percentage of time that the serial bus is actively transmitting data. Because a wide range of factors such as flow control, processor latency, and device architecture can affect serial performance, bus utilization often is not 100 percent. In addition, there is overhead associated with serial communication in the form of start bits, stop bits, and parity bits. This overhead reduces the throughput by 20–30 percent. Thus, the actual data throughput can be considerably less than the bits per second setting.
Page 195 What happens to data sent to a closed serial port? Because serial communication ports are active only when the port is open (for example, by using CreateFile), data may be received and made available only when the port is open. Assume that any data received by a closed com port may be lost or corrupted.
Page 196 Why do loopback tests of large data transfers sometimes have problems? In a typical loopback test, an external wrap plug is used to loop back transmit signals to receive signals. In this configuration, data transmitted is read back on the same serial port to test port communication. Loopback programs often perform this data transfer using a single write followed by a single read, and thus rely on driver software and serial hardware buffering to hold the data between the two function calls. However, these buffers are of finite size, and thus any data transfer that exceeds the buffer size either times out, blocks (due to flow control), or drops data. This behavior is a result of the test design and does not represent a hardware or driver error. Buffer sizes vary between operating systems and hardware, but typically range from 4–8 KB in size.
Page 197 Does the serial hardware have built-in support for protocols such as SDLC and ModBus? Because the serial hardware uses UARTs for communication, protocols such as SDLC and ModBus are not supported in hardware. However, these protocols (or their derivatives) can be supported by software applications that handle the protocol translation.
Page 198 How do I use 9 data bit framing? While NI-Serial software and hardware directly supports only 5, 6, 7, and 8 data bits, it may be possible to use the parity function to create a ninth data bit, depending on your application. To create and control a ninth data bit, enable parity and set parity mark or parity space for a ninth bit of either a 1 or 0, respectively. However, you must do this every time the ninth bit changes state, and thus it may not work for high-throughput applications.
Page 199 Can I use NI serial hardware with a non- Windows platform? Refer to the following table for operating system support for NI serial hardware. NI-Serial Hardware Operating System Support Windows Windows LabVIEW Windows Windows 2000/XP/ XP x64/ Linux Solaris Vista 32 Vista 64 Server Server 2003 2003 x64 PCI-843x PCI-232/485 PXI-843x PXI-842x ENET ExpressCard PCMCIA X NI-VISA Support Native OS Support...
Page 200 Can I use USB serial hardware, Ethernet serial hardware, ExpressCard serial hardware, and plug-in serial hardware in the same computer at the same time? As long as your operating system supports all your NI serial hardware, you can mix different types of serial interfaces in your computer. All NI serial hardware and software is designed and tested for interoperability.
Page 201 Glossary Prefixes Symbols A B C D E F G H I K L M P R S T U V...
Page 202 Prefixes Symbol Prefix Value pico nano 10 µ micro 10 milli kilo mega 10 giga tera...
Page 203 Symbols ° degrees ohms % percent...
Page 204 amperes ANSI American National Standards Institute...
Page 205 bits bytes baud bits per second bps bits per second...
Page 206 Celsius COM Computer Output Microform; used in reference to a communication port CTS clear to send...
Page 207 DB-xx subminiature D connector, where xx is the number of pins data carrier detect data communications equipment or data circuit-terminating equipment dynamic link library direct memory access data set ready data terminal equipment data terminal ready—the overscore denotes that the signal is active low duplex the means of bandwidth usage in a serial system...
Page 208 Electronic Industries Association electromagnetic interference ENET Ethernet...
Page 209 FCC Federal Communications Commission FIFO First-In-First-Out feet...
Page 210 G ground...
Page 211 HSI handshake input HSO handshake output Hertz...
Page 212 input/output IEEE Institute of Electrical and Electronic Engineers inches IRQ interrupt request Industry Standard Architecture...
Page 213 Kbaud kilobits per second...
Page 214 LED light-emitting diode...
Page 215 meters MB megabyte...
Page 216 PC personal computer PCI Peripheral Components Interconnect...
Page 217 RAM random-access memory ring indicator RTS request to send receive RXD receive data—the overscore denotes that the signal is active low...
Page 218 seconds SCSI Small Computer Systems Interface...
Page 219 transmit transmit data—the overscore denotes that the signal is active TXRDY transmit ready—the overscore denotes that the signal is active...
Page 220 UART Universal Asynchronous Receiver/Transmitter...
Page 221 volts VDC volts direct current VXI VME eXtensions for Instrumentation...
Page 222 Important Information Warranty Copyright Trademarks Patents Warning Regarding Use of NI Products Compliance...
Page 223: Warranty
Warranty The serial hardware is warranted against defects in materials and workmanship for a period of one year from the date of shipment, as evidenced by receipts or other documentation. National Instruments will, at its option, repair or replace equipment that proves to be defective during the warranty period. This warranty includes parts and labor. The media on which you receive National Instruments software are warranted not to fail to execute programming instructions, due to defects in materials and workmanship, for a period of 90 days from date of shipment, as evidenced by receipts or other documentation. National Instruments will, at its option, repair or replace software media that do not execute programming instructions if National Instruments receives notice of such defects during the warranty period. National Instruments does not warrant that the operation of the software shall be uninterrupted or error free. A Return Material Authorization (RMA) number must be obtained from the factory and clearly marked on the outside of the package before any equipment will be accepted for warranty work. National Instruments will pay the shipping costs of returning to the owner parts which are covered by warranty. National Instruments believes that the information in this document is accurate. The document has been carefully reviewed for technical accuracy. In the event that technical or typographical errors exist, National Instruments reserves the right to make changes to subsequent editions of this document without prior notice to holders of this edition. The reader should consult National Instruments if errors are suspected. In no event shall National Instruments be liable for any damages arising out of or related to this document or the information contained in it. EXCEPT AS SPECIFIED HEREIN, NATIONAL INSTRUMENTS MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. CUSTOMER'S RIGHT TO RECOVER DAMAGES CAUSED BY FAULT OR NEGLIGENCE ON THE PART OF NATIONAL INSTRUMENTS SHALL BE LIMITED TO THE AMOUNT THERETOFORE PAID BY THE CUSTOMER. NATIONAL INSTRUMENTS WILL NOT BE LIABLE FOR DAMAGES RESULTING...
Page 224 FROM LOSS OF DATA, PROFITS, USE OF PRODUCTS, OR INCIDENTAL OR CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE POSSIBILITY THEREOF. This limitation of the liability of National Instruments will apply regardless of the form of action, whether in contract or tort, including negligence. Any action against National Instruments must be brought within one year after the cause of action accrues. National Instruments shall not be liable for any delay in performance due to causes beyond its reasonable control. The warranty provided herein does not cover damages, defects, malfunctions, or service failures caused by owner's failure to follow the National Instruments installation, operation, or maintenance instructions; owner's modification of the product; owner's abuse, misuse, or negligent acts; and power failure or surges, fire, flood, accident, actions of third parties, or other events outside reasonable control.
Page 225 Copyright Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or mechanical, including photocopying, recording, storing in an information retrieval system, or translating, in whole or in part, without the prior written consent of National Instruments Corporation. National Instruments respects the intellectual property of others, and we ask our users to do the same. NI software is protected by copyright and other intellectual property laws. Where NI software may be used to reproduce software or other materials belonging to others, you may use NI software only to reproduce materials that you may reproduce in accordance with the terms of any applicable license or other legal restriction.
Page 226 Trademarks National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the Terms of Use section on ni.com/legal for more information about National Instruments trademarks. FireWire® is the registered trademark of Apple Computer, Inc. Handle Graphics®, MATLAB®, Real-Time Workshop®, Simulink®, Stateflow®, and xPC TargetBox® are registered trademarks, and TargetBox™ and Target Language Compiler™ are trademarks of The MathWorks, Inc. Tektronix® and Tek are registered trademarks of Tektronix, Inc. Other product and company names mentioned herein are trademarks or trade names of their respective companies. Members of the National Instruments Alliance Partner Program are business entities independent from National Instruments and have no agency, partnership, or joint-venture relationship with National Instruments.
Page 227 Patents For patents covering National Instruments products, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your CD, or ni.com/patents.
Page 228: Warning Regarding Use Of National Instruments Products
WARNING REGARDING USE OF NATIONAL INSTRUMENTS PRODUCTS (1) NATIONAL INSTRUMENTS PRODUCTS ARE NOT DESIGNED WITH COMPONENTS AND TESTING FOR A LEVEL OF RELIABILITY SUITABLE FOR USE IN OR IN CONNECTION WITH SURGICAL IMPLANTS OR AS CRITICAL COMPONENTS IN ANY LIFE SUPPORT SYSTEMS WHOSE FAILURE TO PERFORM CAN REASONABLY BE EXPECTED TO CAUSE SIGNIFICANT INJURY TO A HUMAN. (2) IN ANY APPLICATION, INCLUDING THE ABOVE, RELIABILITY OF OPERATION OF THE SOFTWARE PRODUCTS CAN BE IMPAIRED BY ADVERSE FACTORS, INCLUDING BUT NOT LIMITED TO FLUCTUATIONS IN ELECTRICAL POWER SUPPLY, COMPUTER HARDWARE MALFUNCTIONS, COMPUTER OPERATING SYSTEM SOFTWARE FITNESS, FITNESS OF COMPILERS AND DEVELOPMENT SOFTWARE USED TO DEVELOP AN APPLICATION, INSTALLATION ERRORS, SOFTWARE AND HARDWARE COMPATIBILITY PROBLEMS, MALFUNCTIONS OR FAILURES OF ELECTRONIC MONITORING OR CONTROL DEVICES, TRANSIENT FAILURES OF ELECTRONIC SYSTEMS (HARDWARE AND/OR SOFTWARE), UNANTICIPATED USES OR MISUSES, OR ERRORS ON THE PART OF THE USER OR APPLICATIONS DESIGNER (ADVERSE FACTORS SUCH AS THESE ARE HEREAFTER COLLECTIVELY TERMED "SYSTEM FAILURES"). ANY APPLICATION WHERE A SYSTEM FAILURE WOULD CREATE A RISK OF HARM TO PROPERTY OR PERSONS (INCLUDING THE RISK OF BODILY INJURY AND DEATH) SHOULD NOT BE RELIANT SOLELY UPON ONE FORM OF ELECTRONIC SYSTEM DUE TO THE RISK OF SYSTEM FAILURE. TO AVOID DAMAGE, INJURY, OR DEATH, THE USER OR APPLICATION DESIGNER MUST TAKE REASONABLY PRUDENT STEPS TO PROTECT AGAINST SYSTEM FAILURES, INCLUDING BUT NOT LIMITED TO BACK-UP OR SHUT DOWN MECHANISMS. BECAUSE EACH END-USER SYSTEM IS CUSTOMIZED AND DIFFERS FROM NATIONAL INSTRUMENTS' TESTING PLATFORMS AND BECAUSE A USER OR APPLICATION DESIGNER MAY USE NATIONAL INSTRUMENTS PRODUCTS IN COMBINATION WITH OTHER PRODUCTS IN A MANNER NOT EVALUATED OR CONTEMPLATED BY NATIONAL INSTRUMENTS, THE USER OR...
Page 229 APPLICATION DESIGNER IS ULTIMATELY RESPONSIBLE FOR VERIFYING AND VALIDATING THE SUITABILITY OF NATIONAL INSTRUMENTS PRODUCTS WHENEVER NATIONAL INSTRUMENTS PRODUCTS ARE INCORPORATED IN A SYSTEM OR APPLICATION, INCLUDING, WITHOUT LIMITATION, THE APPROPRIATE DESIGN, PROCESS AND SAFETY LEVEL OF SUCH SYSTEM OR APPLICATION.
Page 230 Compliance with FCC/Canada Radio Frequency Interference Regulations Determining FCC Class The Federal Communications Commission (FCC) has rules to protect wireless communications from interference. The FCC places digital electronics into two classes. These classes are known as Class A (for use in industrial-commercial locations only) or Class B (for use in residential or commercial locations). All National Instruments (NI) products are FCC Class A products. Depending on where it is operated, this Class A product could be subject to restrictions in the FCC rules. (In Canada, the Department of Communications (DOC), of Industry Canada, regulates wireless interference in much the same way.) Digital electronics emit weak signals during normal operation that can affect radio, television, or other wireless products. All Class A products display a simple warning statement of one paragraph in length regarding interference and undesired operation. The FCC rules have restrictions regarding the locations where FCC Class A products can be operated. Consult the FCC Web site at www.fcc.gov for more information.
Page 231 FCC/DOC Warnings This equipment generates and uses radio frequency energy and, if not installed and used in strict accordance with the instructions in this manual and the CE marking Declaration of Conformity*, may cause interference to radio and television reception. Classification requirements are the same for the Federal Communications Commission (FCC) and the Canadian Department of Communications (DOC). Changes or modifications not expressly approved by NI could void the user's authority to operate the equipment under the FCC Rules.
Page 232 Class A Federal Communications Commission This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user is required to correct the interference at their own expense. Canadian Department of Communications This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Page 233 Compliance with EU Directives Users in the European Union (EU) should refer to the Declaration of Conformity (DoC) for information* pertaining to the CE marking. Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory compliance information. To obtain the DoC for this product, visit ni.com/hardref.nsf, search by model number or product line, and click the appropriate link in the Certification column. * The CE marking Declaration of Conformity contains important supplementary information and instructions for the user or installer.
Page 234: Technical Support And Professional Services
Technical Support and Professional Services Visit the following sections of the National Instruments Web site at ni.com for technical support and professional services: Support—Online technical support resources at ni.com/support include the following: Self-Help Resources—For answers and solutions, visit the award-winning National Instruments Web site for software drivers and updates, a searchable KnowledgeBase, product manuals, step-by-step troubleshooting wizards, thousands of example programs, tutorials, application notes, instrument drivers, and so on. Free Technical Support—All registered users receive free Basic Service, which includes access to hundreds of Applications Engineers worldwide in the NI Developer Exchange at ni.com/exchange. National Instruments Applications Engineers make sure every question receives an answer. For information about other technical support options in your area, visit ni.com/services or contact your local office at ni.com/contact. Training and Certification—Visit ni.com/training for self-paced training, eLearning virtual classrooms, interactive CDs, and Certification program information. You also can register for instructor-led, hands-on courses at locations around the world. System Integration—If you have time constraints, limited in-house technical resources, or other project challenges, National Instruments Alliance Partner members can help. To learn more, call your local NI office or visit ni.com/alliance. Declaration of Conformity (DoC)—A DoC is our claim of compliance with the Council of the European Communities using the manufacturer's declaration of conformity. This system affords the user protection for electronic compatibility (EMC) and product safety. You can obtain the DoC for your product by visiting ni.com/certification. Calibration Certificate—If your product supports calibration, you can obtain the calibration certificate for your product at...
Page 235 ni.com/calibration. If you searched ni.com and could not find the answers you need, contact your local office or NI corporate headquarters. You also can visit the Worldwide Offices section of ni.com/niglobal to access the branch office Web sites, which provide up-to-date contact information, support phone numbers, email addresses, and current events.
Page 236: Branch Offices
Branch Offices Office Telephone Number Australia 1800 300 800 Austria 43 662 457990-0 Belgium 32 (0) 2 757 0020 Brazil 55 11 3262 3599 Canada 800 433 3488 China 86 21 5050 9800 Czech Republic 420 224 235 774 Denmark 45 45 76 26 00 Finland 385 (0) 9 725 72511 France 33 (0) 1 57 66 24 24 Germany 49 89 7413130 India 91 80 41190000 Israel 972 0 3 6393737 Italy 39 02 413091 Japan 81 3 5472 2970 Korea 82 02 3451 3400 Lebanon 961 (0) 1 33 28 28 Malaysia 1800 887710 Mexico 01 800 010 0793 Netherlands 31 (0) 348 433 466...
Page 237 South Africa 27 0 11 805 8197 Spain 34 91 640 0085 Sweden 46 (0) 8 587 895 00 Switzerland 41 56 2005151 Taiwan 886 02 2377 2222 Thailand 662 278 6777 Turkey 90 212 279 3031 United Kingdom 44 (0) 1635 523545 United States (Corporate) 512 683 0100...

This manual is also suitable for:

Pci-8431 Pci-232 Pci-485 Pxi-8430 Pxi-8431 Pxi-8433 ... Show all

National Instruments PCI-8430 Manual

Quick Links

Related Manuals for National Instruments PCI-8430

Summary of Contents for National Instruments PCI-8430

This manual is also suitable for:

Table of Contents