Related Manuals for TCS ASX1300 -0010 Series
Summary of Contents for TCS ASX1300 -0010 Series
- Page 1 Product information Audio front door station series ASX1300x-0010 for surface-mount...
-
Page 3: Table Of Contents
Table of contents Scope of delivery......................4 introduction ........................4 Notes on this product information ..........................4 Used symbols and warning notices ..........................4 Further used symbols and designations ........................4 Safety instructions ......................5 General safety regulations ............................5 ... -
Page 4: Scope Of Delivery
Scope of delivery compact front door station ASX1300x-0010 slot screwdriver hexagon ballpoint screwdriver with 2.5 mm wrench size special wrench for exchanging nameplates nameplates empty product information Introduction Notes on this product information This product information refers exclusively to qualified electricians. The product information contains important notes on intended use, installation and initial operation. -
Page 5: Safety Instructions
Observe the safety regulations according to DIN VDE 0100, when working on main power connections of 230 V. When installing TCS:BUS systems the general safety regulations for telecommunication sys- tems according to VDE 0800 must be observed. Inter alia: separated cable routing of high and low voltage lines, ... -
Page 6: Product Description
Product description Intended use The ASX1300x-0010 is audio front door station series with compact design, suitable for the usage in the outdoor and indoor area. The series is suitable for surface-mount. For applications, which differ from the intended use or goes beyond it, the manufacturer ac- cepts no liability. -
Page 7: Device Overview
Device overview upper part of the housing attachment hole loudspeaker rear panel cable gland LED nameplate illumination volume control loudspeaker microphone connection terminal (a, b and P) fitting upper part of the housing volume control microphone bell button with labelling Technical data supply voltage +24 V ±... -
Page 8: Mounting And Installation
Mounting and installation Installation CAUTION! Damages on the device Do not seal the device with silicon under any circumstances! Condensed water must be able to escape and evaporate. Installation site For an optimal operation we recommend a mounting height of 1.50 m (Fig. - Page 9 Assembling the rear panel ► Guide the connection cable (3) through the cable gland (1) of the rear panel (Fig. 3). ► Fix the rear panel with 2 screws (2) to the wall. Observe the installation position of the rear panel. The connection terminal must face upwards.
- Page 10 Closing the device ► Plug the connector of the loudspeaker cable (1) into the appropriate socket (Fig. 6). Fig. 6: Connecting the loudspeaker ► Put on the upper part of the housing (2) onto the rear panel (Fig. 7). ► Turn down the upper part of the housing onto the rear panel (3).
-
Page 11: Connecting The Lines
Labelling the bell button Labelling templates as WORD files are available for download at www.tcsag.de . ► Enter the required names into the labelling template. ► Print the nameplates on the special foil by using a laser printer. ► Alternatively label the special foil with a waterproof marker. ►... -
Page 12: Example Circuit
Example circuit Fig. 10: Circuit diagram For further information see TCS system manual. The TCS system manual can be downloaded at www.tcsag.de. -
Page 13: Initial Operation
Initial operation ► Install the devices of the system completely. ► Proof the a-, b- and P-wire against each other on short-circuit. ► Switch on the mains voltage. Settings For setting the volume use the enclosed slot screwdriver. The volumes are set on an average value ex works. A change is not always required. Adjust the loudspeaker volume ►... -
Page 14: Programming The Bell Buttons
► Ensure that the access to the indoor station in the flat is granted. ► Check if the indoor station is connected to the TCS:BUS. ► Switch on the mains voltage. The operating LED at the power supply and control unit is on. -
Page 15: Cleaning
Power supply and control unit: switch off the programming mode of the system Shortly press the The programming mode of the system is The LED is on. RUN/PROG button. switched OFF. a) Do not press the RUN/PROG button longer than 5 seconds. Otherwise you will activate the light switch function of the front door station. The bell button cannot be programmed. -
Page 16: Information On Disposal
Service Please send your questions and inquiries to TCS HOTLINE hotline@tcsag.de Headquarters TCS TürControlSysteme AG, Geschwister-Scholl-Str. 7, 39307 Genthin | Germany FON: Fax +49(0)3933 8799/-10 +49(0)3933 8799-11 www.tcsag.de Subject to technical changes. TCS Hotline Germany FON: +49(0)4194 9881-188 FAX: +49 4194 988-129, time of printing: 07/2016 E-Mail: hotline@tcsag.de...