Enviroheat 200EH1-14 Operation And Installation Manual
Heat pump
Hide thumbs
Also See for 200EH1-14:
- Operation and installation manual (29 pages) ,
- Owner's manual (20 pages) ,
- Owner's manual (20 pages)
Related Manuals for Enviroheat 200EH1-14
Summary of Contents for Enviroheat 200EH1-14
- Page 1 Heat Pump Water Heater Models: 200EH1-14 200EH1-5 250EH1-15 ENVIROHEAT Please read this manual carefully prior to the use of this water heater. The appearance of the water heater given in this manual is for reference only.
-
Page 2: Table Of Contents
ABLE OF ONTENTS IMPORTANT SAFETY INFORMATION .................. 2 INTERPRETATION OF MARKS AND SYMBOLS ..................2 GENERAL SAFETY INSTRUCTION ......................2 INSTRUCTIONS ON TRANSPORTATION AND STORAGE ................3 FUNCTIONING & PRINCIPLE OF OPERATION ..............4 DESCRIPTION OF PARTS AND COMPONENTS ..............5 TECHNICAL PARAMETERS ........................ -
Page 3: Important Safety Information
MPORTANT AFETY NFORMATION Informa n provided with this warning mark relates to ac vi es that are definitely forbidden or dangerous. Failure to adhere to the instruc ons may result in damage to the product or users may risk personal danger or injury. They relate to the safety of users and the product. -
Page 4: Instructions On Transportation And Storage
Improper disposal is hazardous to your health and the environment. You can obtain further information on how to recycle this product from your municipality, your waste management service or the Enviroheat dealer where you purchased the appliance. User Manual HP M3 r3 DN.docx rev 2019/03... -
Page 5: Functioning & Principle Of Operation
& P UNCTION RINCIPLE OF PERATION A low-pressure liquid refrigerant is vaporized in the heat pump's evaporator and passed into the compressor. As the pressure of the refrigerant increases, so does its temperature. The heated refrigerant runs through a condenser coil within the storage tank, transferring heat to the water stored there. -
Page 6: Description Of Parts And Components
ESCRIPTION OF ARTS AND OMPONENTS Model 200EH1-14 200EH1-5 250EH1-15 Tank Tank volume 195L 195L 246L Rated voltage/ frequency 220V~240V/50Hz 220V~240V/50Hz 220V~240V/50Hz Tank rated pressure 0.7MPa 0.7MPa 0.7MPa Magnesium rod Magnesium rod Magnesium rod IPX4 IPX4 IPX4 Performances Type of system Monobloc air source heat pump 3.04... -
Page 7: Overall Dimensions
Safety valve Hot water outlet Inlet for cold water/drain outlet Air outlet Air inlet Model 200EH1-14 629 270 980 1692 200EH1-5 629 270 980 1692 250EH1-15 629 270 1275 1987 User Manual HP M3 r3 DN.docx rev 2019/03 Page 6... -
Page 8: Exploded View
Exploded View Electric heater Electric cover Front cover - down Display panel Front cover - up Control box Top cover Air grille Air channel - up Four-way valve Compressor Air channel - down Tank case Handle Sensor pocket Power cable (3*1.5mm ①... -
Page 9: Installation Introduction
MPORTANT NTRODUCTION or dust. • Install the appliance on a flat, solid surface. The surface can support the machine weight and the condensate water can be drained freely. in an enclosed space. • Where ambient temperatures are likely to drop below 0°C ensure that adequate Keep an adequate distance between the water heater and bedrooms. -
Page 10: Installation Dimensions
nstallation imensions 50mm Air outlet (φ180mm) Air inlet (φ180mm) Display User Manual HP M3 r3 DN.docx rev 2019/03 Page 9... - Page 11 Condensate Condensate Condensate drain hole drain hole drain hole α 0< <1° α>0 α=0 α α User Manual HP M3 r3 DN.docx rev 2019/03 Page 10...
-
Page 12: Local Standards
Local Standards The following standards and regulations must be taken into account when planning the installation of the Enviroheat water heater system. • AS/NZS 3500.4.2 Na onal plumbing and drainage code hot water supply systems – acceptable solu • HB 263-2004 heated water systems plumbing industry commission. -
Page 13: Supplementary Heat Sources
Supplementary heat sources If a supplementary heat source is connected to the storage tank, the maximum energy input cannot be more than 10 kW, including the electrical element. Where greater input is required, a pressure and temperature relief valve with a higher kW rating is to be fitted to the storage tank. -
Page 14: Plumbing Connections
LUMBING ONNECTIONS Piping Materials Southern Cross Water Heating Pty Ltd. recommends the use of copper pipe, certified to AS1432 Class C, for use in the inlet and outlet lines to the heat pump water system. unless the pipe manufacturer has rated it for temperatures up to 99°C and a minimum water pressure of 600kPa at these temperatures. -
Page 15: Important Safety Information
All water heaters have the ability to produce hot water very quickly. To reduce the the hot water supply pipe work. This valve should be checked every 6 months to Check that the pressure & temperature relief valve drain pipe is not located where it can cause damage if hot water is discharged. -
Page 16: Electrical Connections
LECTRICAL ONNECTIONS temperature cut-out. These devices should not be tampered with or removed. Do not operate this water heater without the electrical thermostat and over temperature cut-out in the circuit. Water heaters shall be equipped with a dedicated power line and a residual current not exceeding 30 mA;... -
Page 17: Commissioning Check List
Commissioning Check List √ The location where the base of the water heater is located is sufficiently compact to avoid subsidence when the system is filled with water. √ Enough room has been allowed for service and maintenance of the water heater. √... -
Page 18: Operation And Functions
PERATION AND UNCTIONS Display The working load of the compressor will be large if the temperature is high in summer. In order to meet the hot water requirements of users and to lengthen service life of the water tank is too low. User Manual HP M3 r3 DN.docx rev 2019/03 Page 17... -
Page 19: Description Of Symbols
Symbol Power ON/OFF switch Timer adjust Auto mode guaranteed comfort; • Set prior to using the heat pump; • If the compressor operates more than the default 8 hours, start the auxiliary power; ECO (off-peak) mode • In this mode, priority is given to using heat pump; 2 –... -
Page 20: Installer Settings
• When menu is open, press to change Factory Adjustment Parameters range Off-peak signal type type of signals,Only allow professional installers to operate. NO , NC - NO corresponds to Normally Open Signal. - NC corresponds to Normally Close Signal. Off-peak logic type - In two ways using heat pump,should set in the installer 01 , 02... -
Page 21: Troubleshooting
Water discharge through the pressure valve All Enviroheat heat pump water heaters have two pressure valves located within the The pressure & temperature valve, located on the storage tank, may also release a small expansion discharge. -
Page 22: Faults And Protection Indication
Digital Reset Compressor over-current Electricity leakage alarm power supply if any line fault occurs The actual water temperature is Over temperature alarm ≥ 85℃ Tank temperature If a short circuit or circuit break sensor fault occurs to the sensor Ambient temperature If a short circuit or circuit break solved, switch on sensor fault... -
Page 23: Maintenance
This will prevent damage to the storage tank in the event of a vacuum or excessive pressure forming at the storage tank. The Enviroheat heat pump hot water system should be drained and flushed every five years during a major service of the unit. -
Page 24: Anode Replacement
Anode replacement The high quality vitreous enamel lined low carbon steel tanks have a sacrificial anode for long tank life. This anode should be inspected every few years and be replaced when it has worn out. As a minimum it is recommended that the anode be changed every 5 years. - Page 25 Product was purchased. All warranty claims must be reported to Enviroheat no later than 14 days from the date the fault is reported to the Enviroheat Dealer. All terms of this warranty are effective from the date of installation of the Product and the attending service person reserves the right to verify this date by requesting a copy of the certificate of...
- Page 26 supplied by the installer. Where the appliance has not been sited in accordance with is assessed as dangerous, service will be refused. Any work required to gain reasonable access to the appliance will be chargeable to of cupboards, doors, walls, or the use of special equipment to move components to floor level.
-
Page 27: Warranty Exclusions
Installer supplied valves and fittings Note 1: If your system is replaced during the warranty period, any State or Federeal government incentives and STC rebates that arise as a result of the installation of the new system shall be assigned to Enviroheat. Warranty Terms... - Page 28 OH&S Disclaimer water systems or the Product. Enviroheat is a supplier of systems only. assembles or services must comply with all OH&S requirements relevant to the type of work being conducted including, but not limited to, plumbing work, work on heights exceeding 2.5m and electrical work.
Need help?
Do you have a question about the 200EH1-14 and is the answer not in the manual?
Questions and answers