Download Print this page

RHINO 2409 Assembly Manual

Loader
Hide thumbs Also See for 2409:

Advertisement

Quick Links

MODEL
MF431
Mounting brackets can be installed using tools ordinarily
available. Shut off tractor engine and engage tractor
brakes during installation.
After loader is installed, check to be sure front tires clear
loader and mounting brackets in all possible positions.
NOTE: Leave all attaching hardware loose until mount-
ing brackets are completely assembled to facilitate as-
sembly and proper alignment. Tighten all hardware to
torque specifications in loader operators manual.
INSTALLING MOUNTING BRACKETS (Figure 1)
1. Remove bolts securing tractor front weight bracket to
tractor front casting. Refasten weight bracket with
front mounting bracket (1) mounted over front weight
bracket using 5/8 x 2" cap screws (15) and 5/8" lock
washers (18).
2. Install left midmounting bracket (4) to tractor trans-
mission casting using 3/4" spacer (5), 5/8" flat
washer (19), 5/8" lock washer (18) and 5/8 x 2-1/2"
cap screw (8) in upper rear hole and 5/8" flat washer
(19), 5/8" lock washer (18) and 5/8 x 1-1/2" cap screw
(9) in upper front hole. Fasten lower holes in left
midmounting bracket using .69" spacers (6), 5/8 lock
washers (18) and 5/8 x 2-1/4" cap screws (16).
F-3978
ASSEMBLY MANUAL
Keep With Operator's Manual
MOUNT KIT
2409 LOADER
MASSEY FERGUSON TRACTORS
2WD
X
1 of 4
4WD
LESS CAB
X
3. Install right midmounting bracket (3) to tractor cast-
ing using 3/4" spacer (5), 5/8" flat washer (19), 5/8"
lock washer (18) and 5/8 x 2-3/4" cap screw (14) in
upper rear hole and 5/8" flat washer (19), 5/8" lock
washer (18) and 5/8 x 1-3/4" cap screw (17) in upper
front hole. Fasten lower holes in right midmounting
bracket using 2.69" spacers (7), 5/8" lock washers
(18) and 5/8 x 4-1/4" cap screws (21).
4. Remove inspection cover plate on underside of
clutch housing.
5. Fasten cross tie (2) to right and left mid mounting
brackets (3 & 4) using 5/8 x 2" cap screws (15) and
5/8" lock nuts (20).
6. Fasten cross tie to bottom of tractor using 5/8" flat
washers (19), 5/8" lock washers (18) and 5/8 x 1-3/4"
cap screws (17).
2-7414
WITH CAB
7-2-2004

Advertisement

loading

Summary of Contents for RHINO 2409

  • Page 1 ASSEMBLY MANUAL 2-7414 Keep With Operator's Manual MOUNT KIT 2409 LOADER MASSEY FERGUSON TRACTORS MODEL LESS CAB WITH CAB MF431 Mounting brackets can be installed using tools ordinarily 3. Install right midmounting bracket (3) to tractor cast- available. Shut off tractor engine and engage tractor ing using 3/4”...
  • Page 2 2-7414 PARTS LIST - MOUNTING KIT ITEM PART NO. DESCRIPTION QTY. 52371 BRACKET, Front Mounting 51864 CROSS TIE 51861 BRACKET, Midmounting, Right 51868 BRACKET, Midmounting, Left 42787-1 SPACER TUBE .75" 42787-7 SPACER TUBE .69" 42787-6 SPACER TUBE 2.69” 41838-64 SCREW, Cap, 5/8-11 x 2-1/2 41838-29 SCREW, Cap, 5/8-11 x 1-1/2 41838-7...
  • Page 3 2-7414 Figure 1 Mount Kit Assembly F-3978 3 of 4 7-2-2004...
  • Page 4 2-7414 INSTALLING LOADER TO MOUNTING INSTALLING BUCKET BRACKETS (Continued) Refer to instruction sheet for instructions on installing bucket. 4. Reposition overhead hoist by looping nylon strap around yoke near loader side frames at balance INSTALLING BUCKET LEVEL INDICATOR point of loader. 1.