Advertisement
•
Push the tank into place carefully. If it knocks against the
walls or is incorrectly inserted, the appliance may not
function. (The tank full light flashes.) Remove the tank
then replace carefully in position.
3.2
Continuous external draining
If the appliance is to be operated for long periods but you are
unable to empty the tank regularly, you are recommended to use
continuous draining. Proceed as follows:
1. Remove the rubber bung from the outlet tube (Fig. 4).
2. Fasten the rubber hose to the spout (fig. 5).
3. Make sure the hose is no higher than the spout (fig.
6), otherwise the water will flow into the tank of the
appliance. Make sure there are no kinks in the hose.
Please note:
•
Keep the rubber bung. You will need it to plug the hose or
close the outlet tube if you revert to draining into the tank.
4. MODE SELECTION
1. Plug the appliance into a mains socket:
C6
C4
2. Touch the ON/STAND-BY button
to turn the appliance on: the appliance will operate in the
previously-set mode and the deflector (A2) opens in a
preset position.
To turn the appliance off, touch the ON/STAND-BY button again.
Please note:
If
(C7) appears on the display, it is necessary to empty or
correctly position the tank (A7) (see paragraph "3.1 Draining
into the tank").
•
Place the dehumidifier at least than 30 cm from the
laundry to be dried. NEVER place the dehumidifier under
the laundry to be dried.
•
Before unplugging from the mains, wait for the fan to stop.
The fan remains in operation for about two minutes after
the appliance is turned off to allow the heating element to
cool down.
•
When started up, or when power is restored, the appliance
operates in the mode selected before it shut down.
Important: Before unplugging from the mains, wait for
the fan to stop. The fan remains in operation for about
two minutes after the appliance is turned off to allow
the heating element to cool down.
4.1 Dehumidifying mode
Touch the MODE button (B2) to select modes, the deflector
opens and the appliance comes in AUTO mode (fig. 7).
The display will show:
•
AUTO: To maintain a comfortable level of humidity. The
unit controls room humidity in 45~50% RH. Fan speed is
automatically controlled (high or low).
C3
C7
C2
C3
C2
C1
C2
C1
C1
C5
C5
C5
C7
C3
(B1) for 2/3 seconds
C2
C1
B4
C5
B5
B3
B2
C7
C3
B6
C2
B1
C7
C3
C1
C2
C5
C1
(Auto will light on by default at the first run).
DRY
: Super dry mode to dry laundry. Use this
programme to dry garments rapidly and or during the
winter.
B4
•
MIN
: for silent operation. The unit automatically
dehumidifies in low fan speed and low noise.
•
MAX
B5
high fan and controls room humidity in 35~40% RH.
•
ECO: Eco mode to dry laundry (high fan, low heater).
C6
Use this programme during the summer. The appliance
B3
operates automatically with low energy consumption.
Please note:
•
The humidity display shows relative humidity status
B2
of room air. Due to condition of machine position, air
circulation and sensor accuracy, the values are for reference
only that may have variations around ±10%RH.
B6
4.2 Ioniser mode
1. Before using this function, make sure the appliance is on.
C7
Touch the ioniser button (B4). The
(Fig.8) and the appliance emits negative ions from the air
B1
C3
outlet grille (A9).
2. Touch the ioniser button again to interrupt negative ion
C2
emission. (The symbol on display goes off).
A large quantity of negative ions are produced, quantitatively
similar to those present in environments such as forests or
C7
waterfalls.
C1
4.3 Delayed shutdown timer
C3
1. Before using this function, make sure the appliance is on.
C7
2. Each time the Timer button (B5) is touched, the number of
C6
C2
hours the appliance operates changes and the
C5
C3
displayed (Fig.10):
1 h - 2 h - 3 h ..... 12 h - continuous (no showing).
C2
C1
When the timer is set, the remaining hours will show. Even if
the tank full icon is flashing and the unit stops, the counting
C6
C4
continues. After emptying and repositioning the tank, the
C1
appliance continues to operate for the time left (may just a few
C5
time left, in this case, you may want to reset the timer.)
4.4 LCD dimmer
•
Touch the LCD dimmer button (B3) to show the current
C5
setting (Fig. 9) and touch again to set the backlight, on the
display appears:
H (full light) - L5 - L4 - L3 - L2 - L1 - L0 (no backlight) (C3).
After setting (or without touching the key for 5 seconds), the
icon (C9) will be displayed showing if the dimmer setting
is among L0 and L5 (and disappears when the setting is H), and
the display will show the timer if it has been set.
11
: to dehumidify rapidly. The unit runs
C4
C6
C4
C6
C4
icon (C4) comes on
C6
C4
B4
B5
B3
B4
B5
B3
B5
B3
B2
B3
B2
B6
B2
B6
B1
B6
B1
B1
B4
B5
C4
B3
B2
B6
will be
B1
B4
B5
B3
B2
B6
Advertisement
