Makita CL104D Instruction Manual page 10

3. Overlap the frame of dust stopper with that of the
dust bag.
► Fig.13
4. Place the dust stopper and the dust bag together
into the cleaner cavity in the same direction of
arrow on the dust stopper. Insert them all the way
into the slots in the cleaner cavity.
► Fig.14: 1. Cleaner cavity
5. Place the entire cloth part of the dust bag inside
the tool itself.
► Fig.15: 1. Front cover
6. Close the front cover completely.
► Fig.16: 1. Front cover
Installing the paper pack
1. Unfold the entrance of the paper pack before
setting it on the dust stopper.
► Fig.17
► Fig.18: 1. Upper side of dust stopper 2. Lower side
of dust stopper
Use the dust stopper also when installing paper pack.
Be careful not to take the upper side for the lower side
by mistake because they are different each other.
2. Insert the protrusion of the paper pack into the
groove in the dust stopper as shown in the figure.
► Fig.19: 1. Dust stopper 2. Paper pack 3. Groove
3. There is no distinction between the upper and
lower sides of the paper pack. You may insert its
protrusion of any side into the lower groove of the
dust stopper.
► Fig.20: 1. Lower groove
4. Overlap the frame of dust stopper with that of the
paper pack.
► Fig.21
5. Place the dust stopper and the paper pack
together into the cleaner cavity in the same direc-
tion of arrow on the dust stopper. Insert them all
the way into the slots in the cleaner cavity.
► Fig.22: 1. Cleaner cavity
6. Place the entire container part of the paper pack
inside the tool itself.
► Fig.23: 1. Front cover
7. Close the front cover completely.
CAUTION:
• Install the dust stopper with the dust bag or
paper pack properly. Tool operation without
proper installation of them, or using broken
or ripped one, it may allow dust to get into the
motor. This may result in motor failure.
• Do not fold the cardboard at its opening when
installing the paper pack.
• Never throw away the dust stopper because it
needs to be used repeatedly whenever either
the dust bag or the paper pack is used.
• The paper pack for the cleaner is an important
component for maintaining the tool perfor-
mance. If you use the other genuine paper pack,
it may cause smokes or ignition.
OPERATION
► Fig.24
To connect attachments, such as nozzle, twist and
insert them to ensure secure connection during use. To
disconnect attachments, twist and remove them.
Cleaning (Suction)
Nozzle
► Fig.25: 1. Nozzle
Attach the nozzle to clean off tables, desks, furniture,
etc. Nozzle slips on easily.
Nozzle + Extension wand (Straight pipe)
► Fig.26: 1. Nozzle 2. Extension wand
The extension wand fits in between the nozzle and the
cleaner itself. This arrangement is convenient for clean-
ing a floor while standing erect.
Corner nozzle
► Fig.27: 1. Corner nozzle
Fit on the corner nozzle for cleaning corners and crev-
ices of a car or furniture.
Corner nozzle +Extension wand
(Straight pipe)
► Fig.28: 1. Corner nozzle 2. Extension wand
In tight quarters where the cleaner itself cannot
squeeze in, or in high places hard to reach, use this
arrangement.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off
before attempting to perform inspection or
maintenance.
After use
► Fig.29
When storing or charging the cleaner, lock the nozzle
head, and hang it from a hook available in the market.
CAUTION:
• Putting the cleaner against the wall without a
hook may cause the cleaner to fall down and be
damaged.
► Fig.30
Cleaning
► Fig.31
From time to time wipe off the outside (cleaner body) of
the cleaner using a cloth dampened in soapy water.
Clean out also the suction opening, dust bag/paper
pack mounting area and the dust stopper.
10 ENGLISH