Related Manuals for Weidmuller Power Monitor 51A
Summary of Contents for Weidmuller Power Monitor 51A
- Page 1 Power Monitor / Power Monitor 51A Quick guide to set up a connection with the Power Monitor devices through the Weidmüller Serial/Ethernet Converter...
-
Page 3: Revision History
Revision history Version Date Change 11/2013 First edition 03/2015 Page 5, software Power Monitor Manager updated from version 1.10 to version 1.20 Contact address Weidmüller Interface GmbH & Co. KG PO Box 3030 32720 Detmold Klingenbergstraße 16 32758 Detmold Germany Phone +49 (0) 5231 14-0 +49 (0) 5231 14-2083... -
Page 4: Table Of Contents
Table of contents Table of contents Revision history ..........................3 Contact address ..........................3 Table of contents ....................... 4 Introduction ......................5 Copyright and trademark ......................... 5 Types / article numbers ........................5 Requirements ............................ 5 Configuring Serial/Ethernet Converter ..............6 Configuring Power Monitor ................ -
Page 5: Introduction
– RS485 input article numbers supply) Power Monitor 1423550000 Power Monitor 51A 1470260000 Ethernet connection • Connect the Serial/Ethernet Converter to your local ethernet or directly to your computing device via an RJ45 cable. Requirements • Make sure you are in the same IP range as the Please set up the Serial/Ethernet Converter as Serial/Ethernet Converter. -
Page 6: Configuring Serial/Ethernet Converter
Configuring Serial/Ethernet Converter Configuring Serial/Ethernet Converter Start S/E-Converter Administrator. STEP 1 Click on [Search]. If you have connected the Serial/Ethernet Converter properly to your STEP 2 network the software will find the device. Mark the device in the table. STEP 3 Click on [Configure]. - Page 7 Configuring Serial/Ethernet Converter Click on [Network) to see the network configuration. Click the [Modify] check box to modify STEP 5 the configuration if needed. 1502950000/01/03.15...
- Page 8 Configuring Serial/Ethernet Converter Click on the [Serial] tab. STEP 6 Click the [Modify] check box. STEP 7 Mark the device in the table. STEP 8 Click on the [Settings] button. STEP 9 1502950000/01/03.15...
- Page 9 Configuring Serial/Ethernet Converter Set the parameters as follows: STEP 10 • Baud Rate: 19200 • Parity: • Data Bits: • Stop Bits: • Flow Control: None • FIFO: Enable • Interface: RS-485, 2 wire NOTICE All values must be equal to the values in the Power Monitor. Confirm by clicking on [OK].
- Page 10 Configuring Serial/Ethernet Converter Click the [Operating Mode] tab. STEP 12 Click the [Modify] check box. STEP 13 Mark the first row in the table. STEP 14 Click on [Settings] and set [Operating Mode] to “Real COM Mode”. STEP 15 Confirm by clicking on [OK]. STEP 16 1502950000/01/03.15...
- Page 11 Configuring Serial/Ethernet Converter Click on [COM Mapping]. STEP 17 Click on [Add], check the box and confirm by clicking on [OK]. STEP 18 1502950000/01/03.15...
- Page 12 Configuring Serial/Ethernet Converter 1502950000/01/03.15...
- Page 13 Configuring Serial/Ethernet Converter Click on the upper row in the main window. STEP 19 Click on [Configure]. STEP 20 Select a COM Port. STEP 21 1502950000/01/03.15...
- Page 14 Configuring Serial/Ethernet Converter Click on the [Serial Parameters] tab. STEP 22 Set the parameters to the same values as in step 10 and on the Power Monitor, i.e. STEP 23 • Baud Rate: 19200 • Parity: • Data Bits: • Stop Bits: •...
-
Page 15: Configuring Power Monitor
Configuring Power Monitor Configuring Power Monitor Firstly, please change the protocol from MEWTOCOL to MODBUS in the Power Monitor and set communica- tion parameters as follows: • Baud Rate: 19200 • Parity: • Data Bits: • Stop Bits: Start the Weidmüller Power Monitor Manager. STEP 26 Under [Settings] select [Communication setup]. - Page 16 Configuring Power Monitor Set [Network] to “RS232C“. STEP 28 Set [Communication port] to the same port as described in step 22. STEP 29 Set the other parameters to the same values as in step 10 and on the Power Monitor: STEP 30 •...
- Page 17 Configuring Power Monitor NOTICE All values must be equal to the values in the Power Monitor. Confirm by clicking on [OK]. STEP 31 1502950000/01/03.15...
- Page 18 Configuring Power Monitor Click on [Display]. STEP 32 Now there must be a connection between the Power Monitor and the computer (see status on the bottom left “Communication success”). 1502950000/01/03.15...
- Page 20 Weidmüller Interface GmbH & Co. KG PO Box 3030 32720 Detmold Klingenbergstraße 16 32758 Detmold Germany Phone +49 (0) 5231 14-0 +49 (0) 5231 14-2083 E-mail info@weidmueller.com Order number: Internet www.weidmueller.com 1502950000/01/03.15...