DENTSPLY ECLIPSE 9494800 Owner's/Operator's Manual
  1. Manuals
  2. Brands
  3. DENTSPLY Manuals
  4. Recording Equipment
  5. ECLIPSE 9494800
  6. Owner's/operator's manual
DENTSPLY ECLIPSE 9494800 Owner's/Operator's Manual

DENTSPLY ECLIPSE 9494800 Owner's/Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Summary of Contents for DENTSPLY ECLIPSE 9494800

  • Page 2: Symbol Table

    SAFETY: FOR PROFESSIONAL USE ONLY. Please read these operating instructions carefully before installing or operating this equipment. Use indoors only. • Never operate the unit in close proximity to combustible materials or place materials on top of the unit. • The unit must be electrically grounded to a three wire electrical outlet or receptacle.

  • Page 3: Technical Data

    TECHNICAL DATA: ELECTRICAL RATINGS: Model Number Volts Amps Frequency Watts 9494800 120V 50 - 60Hz 1200W 9494801 220-240V 50 - 60Hz 1200W 9494900 100V 50 – 60Hz 1200W DIMENSIONS: Length: 510mm (20.1”) Width: 366mm (14.4”) Height: 385mm (15.15”) WEIGHT: 120V: 25kg (55 lbs) 230V: 25kg (55 lbs) OPERATING TEMPERATURE: 5°C –...

  • Page 4: Installation Instructions

    INSTALLATION INSTRUCTIONS: Shipping damage should be reported to the carrier as soon as detected. The Unit Package contains the following: Owner & Operators Manual (this document) Eclipse Processing Unit w/Power Cord 2 Spare Bulbs Turntable Gloves (1pr.) 10A Fuse (2) - (230V only) 4.0A Fuse (1) UNPACKING: Save the box and other packing material for future use in transporting the unit.

  • Page 7: Select Process

    GENERAL OPERATION: Cont. When the unit is turned on by means of the power switch a diagnostic test is performed to check the operation of key systems in the unit. The screen shown below will be displayed. If a problem exists an error will be displayed. Reference errors in the troubleshooting section of this manual.
  • Page 8 GENERAL OPERATION: Cont. Once a process is selected, push the PROG key or the START/STOP key to confirm the Process Parameter Screen. PROCESS PARAMETER SCREEN This screen shows the name of the process selected, the number of lamps used and its cycle time (excluding the 3 minutes of cooling time).
  • Page 9 GENERAL OPERATION: Cont. COOLING SCREEN Once cooling is completed the display will return to the process menu. The last process used will again be highlighted on the process menu. ABORT PROCESS: When the START/STOP key has been pressed during a process, the following screen is shown to confirm the aborting of the process.
  • Page 10 GENERAL OPERATION: Cont. LOADING CARD PROGRAMS From this screen, insert card with label facing up. Press the PROG key to load data. Program loading. Program loaded, remove card. Display will return to Select Process.

  • Page 11: Maintenance

    WARNING: This equipment contains dangerous voltages. Maintenance and repair work should only be performed by an authorized service technician of DENTSPLY Prosthetics. To keep the equipment in good working order you should follow the guidelines below. Examine the equipment regularly for mechanical damage.
  • Page 14 MAINTENANCE: Cont. FUSE REPLACEMENT (220-240V UNITS ONLY): Mains - located in the rear of the unit inside the inlet socket. 1. Turn the power switch OFF 2. Unplug the unit. 3. Remove fuse drawer from inlet socket (contains 2 fuses) 4.

  • Page 15: Troubleshooting

    Make sure the table handle is pushed completely forward and the lift is in the DOWN position, then push ESC. If the lift is still elevated, turn OFF the unit, open the door and gently push the table down to the stop position. Turn the unit ON. Call DENTSPLY service department if problem persists. OVER TEMPERATURE ERROR 2 The temperature of the unit has exceeded the maximum temperature allowed.

  • Page 16: Power Failure

    The horizontal light beam was not detected to stop lift. Make sure that nothing is obstructing the lift and the lift in the down position. • Call DENTSPLY service department if problem persists. POWER FAILURE AC line power was lost during a process.

  • Page 17: Product Service

    Call DENTSPLY at the phone number below and obtain a service manual for a nominal fee • BEFORE RETURNING THE UNIT: Call DENTSPLY for an PR number. This is used to track and identify your unit. Equipment received without this number • may not be identifiable.
  • Page 19 _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________...

  • Page 20: Warranty

    WARRANTY: Except with respect to those components parts and uses which are hereinafter described, DENTSPLY Prosthetics warrants this furnace to be free from defects in material and workmanship for a period of one year from the date of sale. DENTSPLY Prosthetics’ liability under this warranty is limited solely to repairing or, at DENTSPLY Prosthetics’...

This manual is also suitable for:

Eclipse 9494801Eclipse 9494900

Table of Contents