Table of Contents
Advertisement
Quick Links
Avaya X330W-2USP
WAN Access Router Module
Quick Start Guide
Note:
You should upgrade the P330 switch firmware and
Embedded Web Manager to version 3.12 or higher
before installing the X330W-2USP module.
If you need to upgrade the software, obtain the
latest version of the software from
avaya.com/support/ and download it according to
the instructions in the User's Guide.
Important Safety
Information
Unpack the Module
Insert the Module
Connect to the Ports
Configure the Module
Run the Embedded Web
(optional)
1
2
3
4
5
6
Advertisement
Table of Contents
Related Manuals for Avaya X330W-2USP
Summary of Contents for Avaya X330W-2USP
-
Page 1: Quick Start Guide
Note: You should upgrade the P330 switch firmware and Embedded Web Manager to version 3.12 or higher before installing the X330W-2USP module. If you need to upgrade the software, obtain the latest version of the software from Connect to the Ports avaya.com/support/ and download it according to... -
Page 2: Important Safety Information
Do not touch the top or bottom of the circuit board. If possible, wear a wrist-strap and use an anti-static bag. Caution: The Avaya P330 switch must not be operated with the expansion slot open. The expansion slot should either include a sub-module, or be covered with the supplied blanking... -
Page 3: Unpack The Module
• One X330W-2USP WAN Access Router Module. Connection cables are not supplied. Documentation • Avaya X330W-2USP WAN Access Router Modules Quick Start Guide (this document). • Avaya X330W-2USP WAN Access Router Modules Release Notes. • Avaya X330WAN Documentation and Utilities CD. -
Page 4: Insert The Module
Board (PCB) is aligned with the guide rails. The PCB fits into the guide rails and not the metal base plate. Press in the expansion module firmly until it is completely inserted into the Avaya P330 switch. Gently tighten the two screws on the front panel of the expansion module by turning them clockwise. - Page 5 The serial port on the front panel is labeled “Console” and has an RJ-45 socket. Insert the RJ-45 plug on the console cable into the Console port of the Avaya X330W-2USP module. Insert the other end into the RJ-45 socket in the supplied DB-9 adapter.
-
Page 6: Configure The Module
Configure the Module Before you can set up the X330W-2USP module you must power on and set up the Avaya P330 stack as described in the Avaya P330 User’s Guide. You can configure the X330W-2USP module either via its console port or by opening a session to the module from the P330 switch in which the module is installed using the command. - Page 7 All CLI commands mentioned in this section are described in the Avaya X330WAN User’s Guide. To configure a modem interface: Connect a terminal to the Console port of the X330W-2USP as described in “Connecting the Console Port”. When prompted for a Login Name, enter the default name root and press Enter.
-
Page 8: Configuring Loopback Interfaces
Configuring Loopback Interfaces All CLI commands mentioned in this section are described in the X330WAN User’s Guide. To configure Loopback interfaces: Use the command to enter the Interface interface loopback <loopback number> Loopback mode. For example, typing configures a loopback with a interface loopback 1 Loopback interface number 1. -
Page 9: Configuring The Fabricfastethernet Interface
Configuring the FabricFastEthernet Interface To configure a FabricFastEthernet interface: Use the interface command to enter the FabricFastEthernet <if-number> FabricFastEthernet interface context, where the if-number format is port[:vlan[.ip- interface index]] You do not need to include the ip-interface index if you configure only one IP interface. Use the command to assign an IP address to the interface. -
Page 10: Configuring Usp Interfaces
Configuring USP Interfaces All CLI commands mentioned in this section are described in the X330WAN User’s Guide. To configure USP interfaces: Use the command to enter the context of the serial interface serial <if-number> interface you want to configure. If you require Frame Relay encapsulation, continue with step 6. After the interface is created, its default encapsulation is PPP. - Page 11 Verify that you can communicate with the X330W-2USP using the ping command to the IP address of the X330W-2USP you chose. If there is no response, check the IP address and default gateway of both the X330W-2USP and the station.
- Page 12 X330W-2USP Default Settings The default settings for the X330W-2USP and its ports are determined by its embedded software. These default settings are subject to change. If you wish to change the default parameters, we recommend that you use the CLI. Please refer to the Avaya X330WAN User’s Guide.
-
Page 13: System Requirements
Verify that there is communication between the Master Switch and the X330W-2USP using the ping command to the pmi of the X330W-2USP. If there is no response, check the IP address and default gateway of both the X330W-2USP and the Master Switch. - Page 14 Follow the on-screen instructions. • Or install the plug-in from the Avaya site by clicking on the link on the welcome page. • Or, if the network manager has placed the files on the local site, install the plug-in from there by clicking the link on the welcome page.
-
Page 15: Documentation And Online Help
Documentation and Online Help Refer to the Avaya X330WAN Documentation and Utilities CD for full instructions. -
Page 16: How To Contact Us
To contact Avaya’s technical support: In the United States Dial 1-800-237-0016, press 0, then press 73300. From Outside the United States In the EMEA (Europe, Middle East and Africa) Region. Email: csctechnical@avaya.com Country Local Dial-In Number Country Local Dial-In Number...