Advertisement
6. Connect the single LC connector or dual LC connectors of the fiber-optic cable to the
appropriate SFP+ module.
7. (SFP-10G-S-U, SFP-10G-S-D, SFP-10G-S-U-10, and SFP-10G-S-D-10 only) Do the
following:
a. Remove a dust cap from one end of the included SC-to-SC adapter. Save the dust
cap for future use.
b. Connect the adapter to the included patch cord.
c. Remove the dust cap from the other end of the adapter. Save the dust cap for future
use.
d. Connect the adapter to the existing CresFiber
To remove an SFP+ module from an SFP+ cage, do the following:
1. Disconnect the single LC cable connector or dual LC cable connectors from the
SFP+ module.
2. Reinstall the dust cap onto each LC cable connector.
3. (SFP-10G-S-U, SFP-10G-S-D, SFP-10G-S-U-10, and SFP-10G-S-D-10 only) Do the
following:
a. Disconnect the SC-to-SC adapter from the patch cord.
b. Reinstall the dust caps on each end of the adapter and on the SC connectors of the
patch cord.
As of the date of manufacture, the product has been tested and found to comply with specifications for CE marking.
This product is a Recognized Component to applicable UL Standards and requirements by Underwriters
Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the
user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
DO
GUIDE
8G fiber-optic cable.
®
4. Remove the SFP+ module from the SFP+ cage by doing the following:
a. Open the bail latch by pulling it outward and downward.
b. Grasp the SFP+ module, and then carefully remove the module from the SFP+ cage.
5. Close the bail latch.
6. Reinstall the dust cap into the optical bores of the SFP+ module.
DO
Learn More
Visit the website for additional information and the latest firmware updates. To learn
more about this product, use a QR reader application on your mobile device to scan
the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The products are Class 1 laser products. They comply with safety regulations of IEC-60825-1,
FDA 21 CFR 1040 11 and FDA 21 CFR 1040 10.
WARNING: Visible and invisible laser radiation when open. Avoid direct exposure to beam.
NOTE: Plug the included dust cap into the optical transceiver when the fiber-optic cable is unplugged.
The specific patents that cover Crestron products are listed at http://www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.
Crestron, the Crestron logo, and CresFiber are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. UL and the UL logo are either
trademarks or registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used
in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not
responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2016 Crestron Electronics, Inc.
The product warranty can be found at www.crestron.com/warranty.
DOC. 7862A (2046979) 06.16
Specifications subject to change without notice.
Advertisement
