WinWing Super Libra J1 User Manual

Joystick base for f18 grip+

Advertisement

F18 GRIP+ J1 SUPER LIBRA JOYSTICK BASE
User manual
V 1.1
1
J1-SUPER LIBRA JOYSTICK BASE Product Introduction ............................................ 1
1.1
Function introduction ............................................................................................... 2
1.2
Disassembly steps .................................................................................................. 3
1.3
Median calibration and median offset ..................................................................... 6
1.4
Assembly steps ....................................................................................................... 7
1.5
Damping adjustment ............................................................................................... 9
1.6
AM and Spring settings ........................................................................................... 9
2
F18-JGRIP Product Introduction .................................................................................. 11
2.1
Key map introduce ................................................................................................ 11
2.2
Joystick Grip installation angle introduction .......................................................... 12
2.3
Combinations of products (optional) ..................................................................... 13
3
J1-HOLDER .................................................................................................................. 14
3.1
J1-HOLDER Adjustment instructions .................................................................... 14
4
Other installation methods(Official advice) ................................................................... 16
4.1
Gaming chair installation ....................................................................................... 16

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Super Libra J1 and is the answer not in the manual?

Questions and answers

Summary of Contents for WinWing Super Libra J1

  • Page 1: Table Of Contents

    F18 GRIP+ J1 SUPER LIBRA JOYSTICK BASE User manual V 1.1 J1-SUPER LIBRA JOYSTICK BASE Product Introduction ..........1 Function introduction ....................2 Disassembly steps ....................3 Median calibration and median offset ..............6 Assembly steps ....................... 7 Damping adjustment ....................9 AM and Spring settings ...................
  • Page 2: J1-Super Libra Joystick Base Product Introduction

    1 J1-SUPER LIBRA JOYSTICK BASE Product Introduction Activity range ① F18-JGRIP; ② Z axis kit; ③ Adjustable Extension rod; ④ J1-JOYSTICK BASE;...
  • Page 3: Function Introduction

    Function introduction Roll±20° Pitch±20° Yaw±15° Yaw±15° Roll±20° Pitch±20° 1. Pitch axis rotation angle is ±20°; 2. Roll axis rotation angle is ±20°; 3. Yaw axis rotation angle is ±15°.
  • Page 4: Disassembly Steps

    Disassembly steps 8 PCS 4 PCS...
  • Page 6 1、 Remove 12 screws as shown. 2、 Move the bottom plate and the outer casing to open the bottom plate. 3、 Unplug two connectors. 4、 Remove the shell and bottom plate. 5、 Use the pliers to pull the illustrated screw outward, remove and replace the spring. 6、...
  • Page 7: Median Calibration And Median Offset

    Median calibration and median offset Hold the handle firmly at the target position with your hand, and adjust the clearance between the top wire and the wrench to adjust the gap to no gap (median deviation ±5°).    1.
  • Page 8: Assembly Steps

     Note: The protrusion distance of the two top wires should be bilaterally symmetrical when in the middle position. Assembly steps 6 Pin 4 Pin 4 PCS...
  • Page 9 4 PCS 4 PCS 1. Plug in the lab connectors, 2. The assembly of the bottom plate and the housing requires the use of a wrench to fix the four M3 screws shown in the figure; 3. Install upside need to use the wrench to fix the four M3 screws and four M4 screws.
  • Page 10: Damping Adjustment

    Damping adjustment Roll Pitch   Turn the wrench clockwise downward to increase the damping and vice versa. (Note: Do not loosen excessively) AM and Spring settings Introduction of different feedback on settings. □ □ Configuration introduction table...
  • Page 11 Matching plan J1-BASE 1-BASE J1-BASE J1-BASE +F18-JGRIP +Z Axis +Extension +Z Axis Installation +F18-JGRIP +F18-JGRIP +Extension location +F18-JGRIP □ 5#spring 6#spring (Default) □ 4#spring 5#spring 4#spring A richer operating experience can be achieved by changing the bending arm, spring and spring mounting position.
  • Page 12: F18-Jgrip Product Introduction

    2 F18-JGRIP Product Introduction Key map introduce...
  • Page 13: Joystick Grip Installation Angle Introduction

    Joystick Grip installation angle introduction The extension rod, Z-axis kit and F18-JGRIP can be installed at any angle from 0-360° during the docking process. (Illustration example ±45° two positions installed) Note: Keep the components fixed during the docking process, and only twist the knurled cover to achieve docking.
  • Page 14: Combinations Of Products (Optional)

    Combinations of products (optional) 1、 J1-BASE+Z Axis+Extension+F18-JGRIP 2、 J1-BASE +Extension+F18-JGRIP 3、 J1-BASE+Z Axis +F18-JGRIP 4、 J1-BASE+F18-JGRIP The four matching schemes are all connected with J1-HOLDER. For additional installation, please go to the official website (www.winwing.cn) to download the drawings.
  • Page 15: J1-Holder

    3 J1-HOLDER J1-HOLDER Adjustment instructions The total thickness limits of the table and the block mat is 30mm to 70mm. Install 30mm spacers as required.  The height difference between J1-BASE and the desktop can be changed by adjusting J1- HOLDER (minimum 315mm, maximum 345mm.)
  • Page 16 ADJUST...
  • Page 17: Other Installation Methods(Official Advice)

    4 Other installation methods(Official advice) Gaming chair installation  Those kits are not include in the package. ① 4 of M6 type Flat screw gasket ② 4 of M6 type Elastic screw gasket ③ 4 of M6 30mm-type Allen screws...
  • Page 18 CAUTION: DO NOT USE SCREWS LONGER TOO MUCH TO INSTALL THE BASE ,OR WILL BROKEN PCB INSIDE. Mounting size as shown on picture  If you need drawings, please go to the official website to download (www.winwing.cn)

Table of Contents