Graco 239-766 Instructions Manual
  1. Manuals
  2. Brands
  3. Graco Manuals
  4. Paint Sprayer
  5. 239-766
  6. Instructions manual
Graco 239-766 Instructions Manual

Graco 239-766 Instructions Manual

Fdr pressure control conversion kit for gm 5000 convertible airless paint sprayers
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTIONS-PARTS LIST
This manual contains important
warnings and information.
READ AND KEEP FOR REFERENCE.
INSTRUCTIONS
239–766 FDR Pressure Control
Conversion Kit
For GM 5000 Convertible
Airless Paint Sprayers
GM 5000 Convertible Model: 231–316
21 MPa (210 bar, 3000 psi) Maximum Working Pressure
.
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
COPYRIGHT 1997, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
308–786
First choice when
quality counts.
7433A
Rev. A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 239-766 and is the answer not in the manual?

Questions and answers

Related Manuals for Graco 239-766

Summary of Contents for Graco 239-766

  • Page 1 For GM 5000 Convertible Airless Paint Sprayers GM 5000 Convertible Model: 231–316 21 MPa (210 bar, 3000 psi) Maximum Working Pressure 7433A GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 COPYRIGHT 1997, GRACO INC. Graco Inc. is registered to I.S. EN ISO 9001...

  • Page 2: Pressure Relief Procedure

    NOTE: For information on converting your sprayer 6. Open any fluid drain valves in system. Leave drain to one that safely pumps fluids containing haloge- valve open until ready to dispense again. nated hydrocarbons, contact Graco Product Ser- vice, at 1–800–328–0211. 7. Disconnect spark plug cable.
  • Page 3 Pressure Control Disassembly DISASSEMBLY WARNING FLUID INJECTION HAZARD To reduce the risk of serious injury, follow the Pressure Relief Procedure warning whenever you are instructed to relieve pressure. 44,45 1. Relieve pressure. 02700 2. See Fig. 1. Disconnect hoses (63) from pressure Fig.

  • Page 4: Installation

    Freeze Damage Resistant (FDR) Pressure Control Installation INSTALLATION 6. Slowly tighten screws (54), screw (205), and locknut (204) making sure not to distort filter 1. See Fig. 4. Use conversion kit parts to assemble connection to pressure control. pressure control bracket (207) to pressure control 7.

  • Page 5: Pressure Control

    SEALANT, pipe, sst (not shown) (used 239–518 PRESSURE CONTROL with pressure drain valve (60) (See page 6 for Parts List) 110–838 LOCKNUT, w/nylon insert (5/16”) 290–375 LABEL, identification (GRACO) 112–818 SCREW, cap, hex hd, lg flange 290–437 LABEL, identification (GM5000) 156–849 NIPPLE, pipe, 3/8(m)
  • Page 6 FDR Pressure Control Parts List 05799B 239–518 FDR Pressure Control Part No. Description Part No. Description 239–518 PRESSURE CONTROL 108–358 SEAL (See page 5, item 209 for assembly) 112–373 KNOB 185–565 LABEL 239–519 ENGINE CONTROL BOARD 237–674 CONDUCTOR 107–251 SCREW, panhead, 10–24 x 1 in. 109–078 CONNECTOR 112–610...
  • Page 7 FDR Pressure Control Wiring Diagram BLACK To engine 03496 To clutch field Note: See FDR Pressure Control Parts List for Part Nos.

  • Page 8: Limitation Of Liability

    Graco distributor to the original purchaser for use. With the exception of any special extended or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.

Table of Contents